Manual Cobra Electronics CM/200/3

20 pages 1.22 mb
Download

Go to site of 20

Summary
  • Cobra Electronics CM/200/3 - page 1

    TM Cobra Magnetic Drilling Machine Models CM/200/1 & CM/200/3 OPERATOR’S MANUAL Rotabroach, Imperial works, Sheffield Road, Tinsley, Sheffield S9 2YL. England. Tel: (++44) 0114 221 2500 Fax: (++44) 0114 221 2560 Email: info @rotabraoch.co.uk Web: www.rotabroach.co.uk A MEMBER OF THE OSL GROUP OF COMPANIES This machine (Serial No ) is CE appro ...

  • Cobra Electronics CM/200/3 - page 2

    RLL233 Issue 4 Aug 2007 1 CONTENTS OF THE MANUAL. Page [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] Specification of machine. General procedures and safety measures. Operating instructions. Extension cable selection. Mounting of cutters. Cutters and pilots. Remedies for hole making problems. Wiring diagram. Exploded view and compone ...

  • Cobra Electronics CM/200/3 - page 3

    RLL233 Issue 4 Aug 2007 2 [1] ROTABROACH MAGNETIC DRILLING MACHINE MODELS CM/200/1/ & CM/200/3 Maximum hole cutting capacity in .2/.3C steel = 65mm dia. x 50mm deep Arbor bore = 19.05mm (3/4") dia. Motor Unit Voltages 110v 230v normal full load 14 A 1400 W 6 A 1400 W Electro Magnet 0.6A 69W 0.3A 69W Size 180mm long 90mm wide Tractive Force ...

  • Cobra Electronics CM/200/3 - page 4

    RLL233 Issue 4 Aug 2007 3 READ BEFORE USING THE MACHINE [2] SAFETY PROCEDURES • When using electrical tools, basic safety precautions should always be followed to reduce the risk of electric shock, fire, and personal injury. • Do NOT use in wet or damp conditions. Failure to do so may result in personal injury. • Do NOT use in the presence of ...

  • Cobra Electronics CM/200/3 - page 5

    RLL233 Issue 4 Aug 2007 4 • On completion of the cut, a slug will be ejected. DO NOT operate the machine if the ejected slug may cause injury. [3] OPERATING INSTRUCTIONS • Keep the inside of the cutter clear of swarf. It restricts the operating depth of the cutter. • Ensure that the coolant bottle contains sufficient cutting oil to complete t ...

  • Cobra Electronics CM/200/3 - page 6

    RLL233 Issue 4 Aug 2007 5 SPEED SELECTION The machine is equipped with two speed ranges, High, and Low, and a stepless variation of each range. The speed range is changed by the rotary change switch located on the gearbox side. Do not change gear while the motor is in motion. The stepless variation is adjusted by rotating the disk located on top of ...

  • Cobra Electronics CM/200/3 - page 7

    RLL233 Issue 4 Aug 2007 6 [6] CUTTERS AND PILOTS Diameter. Pilot type. 12 RA3057 13 -18 RA359 19 - 52 RA3047 12 RA3013 13 -17 RA3030 18 - 65 RA356 18 - 36 RA3047 12 SRA3057 13 - 52 SRA25 12 SRA3013 13 - 65 SRA50 18 - 36 SRA25 SCRWC SRC, SRCV SRCL, SRCVL CRWC RCL, RCVL Cutter & Pilot relationship. Cutter designation. RC, RCV ...

  • Cobra Electronics CM/200/3 - page 8

    RLL233 Issue 4 Aug 2007 7 [7] REMEDIES FOR HOLE MAKING PROBLEMS Problem Cause Remedy 1) Magnetic base won't hold effectively Material being cut may be too thin for efficient holding of magnet Swarf or dirt under magnet Irregularity on magnet face or work-piece Insufficient current going to magnet during drilling cycle Attach an additional piec ...

  • Cobra Electronics CM/200/3 - page 9

    RLL233 Issue 4 Aug 2007 8 Problem Cause Remedy 3) Excessive drilling pressure required Incorrectly re-sharpened, worn or chipped cutter Coming down on swarf lying on surface of work-piece Gibs out of adjustment or lack of lubrication Swarf accumulated (packed) inside cutter Incorrect speed selection. Re-sharpen or replace Clean work-piece. Take car ...

  • Cobra Electronics CM/200/3 - page 10

    RLL233 Issue 4 Aug 2007 9 [8] WIRING DIAGRAM ...

  • Cobra Electronics CM/200/3 - page 11

    RLL233 Issue 4 Aug 2007 [9] EXPLODED VIEW OF COMPLETE MACHINE ...

  • Cobra Electronics CM/200/3 - page 12

    RLL233 Issue 4 Aug 2007 Page 11 Item Component Part No. Item Component Part No. Item Component Part No. 1 Guard assembly RD25501 6.6 Internal washer RD4069 9.6 Chain bush RD4521 1.1 Guard RD35522 6.7 Washer RD4070 9.7 Countersunk set screw RD4018 1.2 Pan head screw RD4077 6.8 Saddle clamp RD4071 9.8 Chain RD3558 1.3 Guard bracket RD3246 6.9 Pan hea ...

  • Cobra Electronics CM/200/3 - page 13

    RLL233 Issue 4 Aug 2007 Page 12 [10] EXPLODED VIEW OF GEARBOX AND MOTOR UNITS ...

  • Cobra Electronics CM/200/3 - page 14

    RLL233 Issue 4 Aug 2007 Page 13 Part list of motor & gearbox(Cobra) Item Component Part No. Item Component Part No. Item Component Part No. 1 Motor assembly (110v) RD25521 3.7 Speed controller assembly (110v) RD23330 7.7 Disk spring RD45506 1 Motor assembly (230v) RD25523 3.7 Speed controller assembly (230v) RD23343 7.8 Lock nut RD45503 2 Armat ...

  • Cobra Electronics CM/200/3 - page 15

    RLL233 Issue 4 Aug 2007 Page 14 [11] PIPE ADAPTOR KIT RD2311 FITTING INSTRUCTIONS • Dependent upon the size of the pipe to be cut (see illustrations) attach adjustable angle plates RD3328 with cap screws RD4325 and washers RD4205 (4 off each) to the magnet sides. Do not tighten. • Locate the machine on the centreline pipe taking care that the m ...

  • Cobra Electronics CM/200/3 - page 16

    RLL233 Issue 4 Aug 2007 15 [12] WIRING OF MAINS PLUG The wires of the mains lead are coloured in accordance with the following code: GREEN and YELLOW EARTH BLUE NEUTRAL BROWN LIVE As the colours of the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug - CONNECT AS FOLLOWS; • The wire ...

  • Cobra Electronics CM/200/3 - page 17

    RLL233 Issue 4 Aug 2007 16 13] CUTTING SPEEDS. Material Surface speed (M/min) Aluminium 60-90 Cast iron Soft 30-50 Hard alloy 15-21 Malleable 15-30 Steel Mild (460 N/mm_) 24-30 (460-770 N/mm_) 15-27 (770-1070 N/mm_) 9-15 1070-1230 N/mm_) 6-9 Stainless steel Ferritic 15-18 Austenitic 12-15 Martensitic 9-15 Typical cutting speeds (RPM) for various ma ...

  • Cobra Electronics CM/200/3 - page 18

    RLL233 Issue 4 Aug 2007 17 Cutter diameter and speed relationship High gear. Low gear. Selector No RPM Cutter Dia. Selector No RPM Cutter Dia. 1 300 32 1 150 62 2 360 26 2 180 52 3 430 22 3 215 46 4 500 19 4 250 38 5 600 16 5 300 32 6 650 14 6 330 30 This data is presented for guidance only, and should be adjusted to suit site and material conditio ...

  • Cobra Electronics CM/200/3 - page 19

    RLL233 Issue 4 Aug 2007 18 [14] REPLACEMENT OF MOTOR SUPPLY CABLE. TO REMOVE OLD CABLE AND CHAIN Ensure that the machine is disconnected from any source of power. Failure to do so may result in personal injury. • Remove screws #73 and withdraw the control unit from the housing. • Disconnect the nine-pin cable connector from the control panel ? ...

  • Cobra Electronics CM/200/3 - page 20

    RLL233 Issue 4 Aug 2007 19 The replacement is a complete factory produced assembly, and RD272 (230v) is illustrated below. TO REMOVE OLD CABLE FROM MACHINE • The machine MUST be disconnected from any source of power supply before attempting to conduct any maintenance work. Failure to do so may result in personal injury. • Remove control unit by ...

Manufacturer Cobra Electronics Category Drill

Documents that we receive from a manufacturer of a Cobra Electronics CM/200/3 can be divided into several groups. They are, among others:
- Cobra Electronics technical drawings
- CM/200/3 manuals
- Cobra Electronics product data sheets
- information booklets
- or energy labels Cobra Electronics CM/200/3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cobra Electronics CM/200/3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cobra Electronics CM/200/3, service manual, brief instructions and user manuals Cobra Electronics CM/200/3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cobra Electronics CM/200/3.

A complete manual for the device Cobra Electronics CM/200/3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cobra Electronics CM/200/3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cobra Electronics CM/200/3.

A complete Cobra Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cobra Electronics CM/200/3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cobra Electronics CM/200/3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cobra Electronics CM/200/3, that we can find in the current document
3. Tips how to use the basic functions of the device Cobra Electronics CM/200/3 - which should help us in our first steps of using Cobra Electronics CM/200/3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cobra Electronics CM/200/3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cobra Electronics CM/200/3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cobra Electronics CM/200/3?

Use the form below

If you did not solve your problem by using a manual Cobra Electronics CM/200/3, ask a question using the form below. If a user had a similar problem with Cobra Electronics CM/200/3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)