-
Graco 12 VDC - page 1
311304H Instructions - Parts List GTP10 Pump For pumping gasoline, diesel fu el, and kerosene. Do not use to pump other fluids including water. Models 260000 through 260017, 260019, 260024, 260580, and 260581 10 gpm (38 lpm), 12 VDC (C SA C/US listed motor) Models 260020 an d 260021, 10 gpm (38 lpm), 24 VDC Models 260022 and 260023, 12 gpm (45 lpm) ...
-
Graco 12 VDC - page 2
Models 2 311304H Models Part No. Hose Nozzle 12 VDC, 10 gpm (38 lpm), 12.5 amps 260000 260069 - 12 ft (3.66 m) grounded 260079 - manual, leaded/die sel 260001 260069 - 12 ft (3.66 m) grounded 260082 - automatic, regula r/diesel 260002 260069 - 12 ft (3.66 m) ground ed 260078 - manual, unleaded 260003 260069 - 12 ft (3.66 m) grounded 260083 - automa ...
-
Graco 12 VDC - page 3
Models 311304H 3 ...
-
Graco 12 VDC - page 4
Warnings 4 311304H Warnings The following general warn ings are for the setup, use, ground ing, maintenance, and repair of this equipme nt. Addi- tional, more specific warnings may be found th ro ughout the body of this manual where applicable. Symbols appea r- ing in the body of the manual re fer to these general warnin gs. When these symbols appe ...
-
Graco 12 VDC - page 5
Warnings 311304H 5 EQUIPMENT MISUSE HAZARD Misuse can cause de ath or serious injury. • Do not operate the unit when fatigued or under the influen ce of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equip ment manuals. • Use fluids and solve ...
-
Graco 12 VDC - page 6
Installation 6 311304H Installation When unpacking pump, check for shipp ing damage. Report any shipping damage to delivering carrier imme- diately. Mounting Pump 1. Apply PTFE thread tape (provided with the pump) to large thread of bu ng adapter (9) (2 in. X 1 ½ in. reducer fitting). Install bung ad apter to fuel tank. 2. Assemble s uction tube s ...
-
Graco 12 VDC - page 7
Installation 311304H 7 3. Cut the suction tube so that it is 2 in. (55 mm) from the bottom of the tank when installed in the tank. 4. Insert ga sket (7f) into union nut (1k). If using Grac o supplied PVC suction tube it is not necess ary to apply thread tape before assembly, just scre w into pump inlet (1j). If using me tal suction tube (not sup- p ...
-
Graco 12 VDC - page 8
Installation 8 311304H Electrical Installation 12 VDC and 24 VDC To install wiring for a ne gative grou nd system : 1. Ensure pump switch is OFF. 2. To remove electrical cover (2a) , remove four bolts (2c). 3. Strip 3 in. (76 mm ) of outside insu lation from power cable (6c) from e nd opposite of fuse. 4. Strip 3/8 in. (10 mm) of in sulation from r ...
-
Graco 12 VDC - page 9
Operation 311304H 9 Priming Pump All pump models should prime with in 5 seconds after pump is turned on up to a height of 36 in. (9 1 mm). Pumps installed at height up to 5 ft. (1.52 m) may have difficulty priming. Follow pr ocedure below to initiate prime. Pumps installed at suction height above 5 ft. (1.52 m) will have difficulty in holding prime ...
-
Graco 12 VDC - page 10
Troubleshooting 10 311304H Troubleshooting Problem Cause Solution Motor runs but pump will not prime. Motor rotation wrong. (12 VDC and 24 VDC units only.) Check wiring in structions for possible problems. Missing relief valve o-ri ng seal (4c/7a). Remove gear cover (1b) inspect seal (4c/7a), replace if missing or damaged. Sheared drive key (1f/7 c ...
-
Graco 12 VDC - page 11
Troubleshooti ng 311304H 11 Motor stalls when nozzle is clos ed. Bypass relief valve (4a) stuck. Inspect relief valve, making sure poppet is free. Replace if damaged. Low supply voltage. Check supply voltage. Gears (1c/10a) dam aged and binding. Inspect gears. Gears sh ould turn freely. Replace if damage d. Faulty motor. Replace motor. Fuel leaking ...
-
Graco 12 VDC - page 12
Parts Drawing 12 311304H Parts Drawing 3a 3c 3d/7e 1a 8e 8b 8f 8g 1h 1e/7b/10c 1f/7c/10b 2e 2f 3b 1b 1c/ 10a 1d 4b 4a 2h 2i 8c 8a 8d 4c/ 9 7f 1k 1g/7d 2g 2c 2b 2d 5c 5a 2a 2c 6b 6c 6a Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 2600 ...
-
Graco 12 VDC - page 13
Parts Li st 311304H 13 Parts List Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Ref. No. Description Qty . 1 260458 KIT, pump with swivel, blue (includes items 1a -1k) 260459 KIT, pump without swivel, blue (includes it ...
-
Graco 12 VDC - page 14
Parts List (continued) 14 311304H Parts List (continued) Models 260000 through 260017, 260019, and 260024, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Replacement Danger an d Warning labels, tags, and cards are available at no cost. * Not used on models 260004, 2 60006, 260008, ...
-
Graco 12 VDC - page 15
Technical Data 311304H 15 Technical Data Valox ® is a register ed trademar k of the General Elect ric Company Performance Chart Working pressure 10 psi (0.07 MPa, 0.7 bar) Inlet size 1 in. npt Outlet siz e 3/4 in. npt Weight 20 lb (9 kg) Power cable 18 ft (5.5 m), 14 AWG (12 VDC an d 24 VDC models only) Current draw 12 VDC models: 12.5 amps 24 VDC ...
-
Graco 12 VDC - page 16
All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311304 Graco Headquarters: Minne apolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX ...
У вас вопрос, касающийся Graco 12 VDC?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Graco 12 VDC, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Graco 12 VDC со всей вероятностью он захочет поделиться методом ее решения.