Deutsch dropdown-ico

Bedienungsanleitung RCA 25825

60 Seiten 3.47 mb
Download

Zur Seite of 60

Summary
  • RCA 25825 - page 1

    25825 Digital 8-Line Multihandset System User’s Guide ...

  • RCA 25825 - page 2

    Equipment Approval Information Y our telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for T elephone Terminal Equipment published by ACT A. Notication to the Local Telephone Company On the bottom of this equi ...

  • RCA 25825 - page 3

    you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of P art 68, FCC Rules and Regulations. The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the ...

  • RCA 25825 - page 4

    FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body . This transmitter must not be co-located or operated in conjunction with any other ...

  • RCA 25825 - page 5

    ...

  • RCA 25825 - page 6

    ...

  • RCA 25825 - page 7

    Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. Y our 8-Line Speakerphone is part of a full-featured phone system ideally suited for small to medium-sized oces. It is ...

  • RCA 25825 - page 8

    P arts Checklist Make sure your package includes the following items: Base Handset Handset Cord Network Cord AC Adaptor Important Installation Information • Never install network or telephone wiring during a lightning storm. • Never install network or telephone jacks in wet locations unless the jack is specically designed for wet locations. ...

  • RCA 25825 - page 9

    ...

  • RCA 25825 - page 10

    System Installation: Important Installation Guidelines I Privacy of communications may not be ensured when using this telephone. TAN T: t a s at Connecting your RCA 2580 1 Digital Router: 1 0 ...

  • RCA 25825 - page 11

    Connecting and setting up your RCA 25825 phone: 1. Connect one end of the included Ethernet cable to the WAN port on the back of your 25825 telephone. jack or internet router . 3. Connect the included AC/DC adapter to the port on the back of your 25825 4. After your 25825 telephone initialization and show it's ID number, you can connect the co ...

  • RCA 25825 - page 12

    CAUTION: Make sure that no two base phone units have the same extension. resolved. connected to the system. A maximum of 25 phones can be connected in the system. Next the phone will ask you to enter the ID number of the digital router this phone will be using. The default router ID number is 1, so if you are only using one router , enter 1. Finall ...

  • RCA 25825 - page 13

    V oicemail Turn on the voicemail by pressing the VOICEMAIL button once , a blue indicator will light up. Then select the preferred Mailbox setting. (Personal Mailbox allows you to access the current base mailbox only, or choose General Mailbox to access the operator's mailbox.) For detail information on V oicemail setup and features, please re ...

  • RCA 25825 - page 14

    Ringer Tone The ringers for all eight lines may be set independent of one another . This will help distin- 1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to PHONE OPTIONS. 3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to SET RING TONE. 5. Press the Select so ...

  • RCA 25825 - page 15

    1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to PHONE OPTIONS. 3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to SET PRIORITY LINE. 5. Press the Select softkey . 6. Use the VOL (+ or -) buttons to scroll up or down to 1, 2, 3, 4, 5, 6, 7, or 8. The default ...

  • RCA 25825 - page 16

    3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to SET STA TION NAME. 5. Press the Select softkey . 6. Use the touch-tone pad to enter the phonebook name. Using less than 15 characters is stored in each of the number keys. For example, to enter “Lorraine Smith,” press the 5 key three times for the letter L. Pr ...

  • RCA 25825 - page 17

    Set Backlight 17 1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to PHONE OPTIONS. 3. Press the Select softkey. 4. Use the VOL (+ or -) buttons to scroll up or down to Call Alert Tone. 5. Press the Select softkey. 6. Use the VOL (+ or -) buttons to scroll up or down to On or Off. The default is ...

  • RCA 25825 - page 18

    Local Area Code 1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to SET AREA CODE. 3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to LOCAL AREA CODE. 5. Press the Select softkey . Enter Number shows in the display . 6. Use the touch tone pad on your phone to en ...

  • RCA 25825 - page 19

    Hour Format Y ou may set this phone to a 12 or 24-hour format. The default is 12-hour format. 1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to SET TIME & DATE. 3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to SET HOUR FORMAT . 5. Press the Select softke ...

  • RCA 25825 - page 20

    20 Record a New Greeting to Overwrite the Existing One Any Outgoing Annoucement under 1 second will be treated as invalid. The unit will not record it. Playback Name The Playback Name is what is played to callers when they search for an extension using the dial by name directory . If no name is recorded, the dial by name directory will play a recor ...

  • RCA 25825 - page 21

    2.Use the VOL (+ or -) buttons to scroll up or down to V oicemail. 3.Press the Select softkey . 4.Use the VOL (+ or -) buttons to scroll up or down to Greeting. 5.Press the Select softkey . 6.The system plays the previously recorded greeting. 7.To erase the recorded greeting, press DELETE softkey during greeting playback. Press 8.To stop playback, ...

  • RCA 25825 - page 22

    22 Select the Greeting User can select what type of message greeting to be used for outgoing announcement. 1. Press the MENU softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scrolls up or down to V oicemail. 3. Press the SELECT softkey . 4. Use the VOL (+ or - ) buttons to scrolls up or down to Greeting. 5. Press the SELECT softkey ...

  • RCA 25825 - page 23

    23 3. To stop recording, press Finish softkey to save and exit.. This is considered a standard message and will be included in the message counter . Two-W ay Recording While using the handset or headset, you can record a phone conversation. T he unit will answer incoming calls or routed calls after a set number of rings (pickup delay set in MENU) a ...

  • RCA 25825 - page 24

    5. Press 8 to forward this message to another user on the system; 1. While on a call using the handset or headset, press MEMO to begin recording the conver- sation. 2. Press MEMO again to stop recording. This is a considered standard message and will be included in the message counter . Note: Before you start to record the phone conversation, we su ...

  • RCA 25825 - page 25

    25 Administrator Options Administrator Operation From this menu you will be able to set and change options for the auto attendant and the conference bridge. This includes recording custom auto attendant and conference room greetings, changing passwords and resetting the 2580 1 digital router to its default settings. P assword is required to access ...

  • RCA 25825 - page 26

    26 This menu allows the user to decide whether Auto Attendant will answer all incoming calls. From the Auto Attendant sub-menu: 1. Use the VOL (+ or -) buttons to scroll to “Auto Attendant”. 3. Use the VOL (+ or -) buttons to scroll the options to “Auto Attendant ON/OFF”. 5. Use the VOL (+ or -) buttons to scroll to “YES” or “NO”. r ...

  • RCA 25825 - page 27

    1. Use the VOL (+ or -) buttons to scroll up or down to Day Greeting. 2. Press the Select softkey . 3. Use the VOL (+ or -) buttons to scroll up or down to Record Greeting. 4. After the beep, speak into the phone in a normal tone of voice. (The maximum recording time of an outgoing annoucement is 30 seconds) 5. Press the Select softkey to save or p ...

  • RCA 25825 - page 28

    Review Greeting From the Auto Attendant sub-menu: 1. Use the VOL (+ or -) buttons to scroll up or down to Night/Weekend Greeting. 2. Press the Select softkey . 3. Use the VOL (+ or -) buttons to scroll up or down to Review Greeting. 4. Press the Select softkey . 5. The unit plays the corresponding previously recorded greeting. 6. To erase the recor ...

  • RCA 25825 - page 29

    7. Use the VOL (+ or -) buttons to scroll up or down to select the correct minutes. 8. Press the Select softkey to save. Note: The default setting is 5: 00 pm. Set Weekend Day From the Auto Attendant sub-menu: 1. Use the VOL (+ or -) buttons to scroll up or down to Night/Weekend Greeting. 2. Press the Select softkey . 3. Use the VOL (+ or -) button ...

  • RCA 25825 - page 30

    greeting is: “Hello, thank you for calling.”) 7. To stop playback, press the Exit softkey . Record Greeting This option gives you the opportunity to further customize the auto-attendant by recording over the standard greetings with your own greetings. In order to preserve functionality for both your callers and the users of the system, we recom ...

  • RCA 25825 - page 31

    2. Press the Select softkey . 3. Use the VOL (+ or -) buttons to scroll up or down to General Delivery Mailbox. 4. Press the Select softkey . 5. Use the VOL (+ or -) buttons to scroll up or down to Name. 6. Press the Select softkey . 7. Use the VOL (+ or -) buttons to scroll up or down to Record Name. 9. After the beep, speak into the phone in a no ...

  • RCA 25825 - page 32

    2. Press the Select softkey . 3. Use the VOL (+ or -) buttons to scroll up or down to General Delivery Mailbox. 4. Press the Select softkey . 5. Use the VOL (+ or -) buttons to scroll up or down to Greeting. 6. Press the Select softkey . 7. Use the VOL (+ or -) buttons to scroll up or down to Record Greeting. 9. After the beep, speak into the phone ...

  • RCA 25825 - page 33

    6. Press the Select softkey . 7. Use the VOL (+ or -) buttons to scroll up or down to Select Greeting. 9. Use the VOL (+ or -) buttons to select Name or Greeting. 1 0. Press the Select softkey to save. Dial By Name Directory The Dial by Name directory is a search feature in the Auto Attendant that can be series of names or extensions who’s phone ...

  • RCA 25825 - page 34

    6. Press the Select softkey . 7. Use the VOL (+ or -) buttons to navigate the list of extension numbers. 9. Press the Delete softkey to delete the selected extensions from the list. 1 0. Or press the New softkey to add a new extension into the list. 1 1. Press Select softkey to save or press Exit softkey to cancel. Review V oice Prompt From the Aut ...

  • RCA 25825 - page 35

    9. Press Select softkey to save. 1 0. After the greeting is saved, it will be played back once. Dial Zero for Operator Enabling this option will allow callers to press 0 after the Auto-Attendant answers to be connected with an operator . The default extension for the operator’s phone is 1 00, but this can be changed to any phone on the system. Fr ...

  • RCA 25825 - page 36

    2. Press the Select softkey . 3. Use the VOL (+ or -) buttons to scroll up or down to Dial Zero for operator . 4. Press the Select softkey . 5. Use the VOL (+ or -) buttons to scroll up or down to Review V oice Prompt. 6. Press the Select softkey . 7. The unit plays the corresponding previously recorded greeting. 8. To erase the recorded greeting, ...

  • RCA 25825 - page 37

    6. Press the Select softkey . 7. The unit plays the corresponding previously recorded greeting. 8. To erase the recorded greeting, press Delete softkey during playback. Press Delete again default greeting is “If you know the extension of the person you are trying to reach, please dial it now .”) 9. Press Exit softkey to stop playback. Record V ...

  • RCA 25825 - page 38

    5. Use the VOL (+ or -) buttons to scroll up or down to Conference Room. 6. Press the Select softkey . 7. Use the VOL (+ or -) buttons to scroll up or down to select Conference Room A or Con- ference Room B. 8. Enter the Conference Room settings: Conference Room ON/OFF , Review Greeting, Record V oice Prompt, Room Extension and P assword. 1. After ...

  • RCA 25825 - page 39

    Room Extension 1. After selecting Conference Room A or B, use the VOL (+ or -) buttons to scroll up or down to Room Extension. 2. Press the Select softkey . 3. Key in an extension number in the range between 2000-2099. 4. Press Select softkey to save. Note: The default setting is 2000. Note: The password length should be less than 16 digits. P assw ...

  • RCA 25825 - page 40

    7. Use the VOL (+ or -) buttons to scroll to select your favor music. 8. Press Select softkey to play the music, then press Select soft key to conrm. PBX Restore to Defaults User can restore the PBX to default settings here. 1. Press the Menu softkey . 2. Use the VOL (+ or -) buttons to scroll to Administrator . 5. Use the VOL (+ or -) buttons t ...

  • RCA 25825 - page 41

    Making Calls with an Optional Headset 1. Connect the headset plug into the HEADSET JACK on the right side of the base. 2. Adjust the headset to rest comfortably on top of your head and over your ear . 3. Move the microphone to approximately 2-3 inches from your mouth. 4. Press the HEADSET button and the phone automatically selects the priority line ...

  • RCA 25825 - page 42

    Switching Between the Speakerphone, Handset, and Headset To switch to the speakerphone, press SPEAKER. The speakerphone indicator turns on. Put handset back in cradle. To switch to the headset, press the HEADSET button to enable the headset, and the headset indicator turns on. Hang up the handset. Mute the line cannot hear you, but you can still he ...

  • RCA 25825 - page 43

    Releasing a Call from Hold Press the HOLD button or the corresponding LINE button to release hold. NOTE: If you want to change modes, lift the handset to switch to the handset, or press the NOTE: The call on hold can only be picked up again by this extension only, but then can be transferred to another extension using the Transfer button. 1. With a ...

  • RCA 25825 - page 44

    The indicator on the receiving party’s line rapidly ashes red and rings during call transfer. Once the call is picked up, the indicator stays red. • If the transferred call is not picked up within the other station’s ring delay time, the sta- tion’s V oicemail will answer the call and guide the user to recording their message. Receiving ...

  • RCA 25825 - page 45

    Intercom Calls One-Touch Intercom 1. Press the Intercom/P age button, the speaker turns on, then dial the station number . NOTE: If you want to switch to the handset, pick it up and continue speaking. T o switch to the headset press the HEADSET button. NOTE: The handset, headset, or speakerphone cannot be active when an intercom call is initi- ated ...

  • RCA 25825 - page 46

    4.Press the CONFERENCE button. 5.Speak to both parties. NOTE: If you have more than one party on hold (telephone line or intercom), you must select the line for the party you want to conference with. To disconnect one party: Press the line or intercom button for the person you want to continue speaking with, and the other party is automatically dis ...

  • RCA 25825 - page 47

    b . When you select “Deregister Handset” , the unit will de-register the current cordless handset. NOTE: If there is no cordless handset registered, press and hold the P age button to enter the “P age all stations ” and “Register Handset” selection menu. a. When you select “Register Handset” , the unit will start searching for a cor ...

  • RCA 25825 - page 48

    Press the CID button , and then use the VOL (+ or -) buttons to scroll through the call records. •When you scroll to the start/end of the list, the phone will beep. the screen will show the incoming phone number of each call on each line. Saving a CID Record to the Memory Log or to Phone Book Memory 1. While a name and telephone number shows in t ...

  • RCA 25825 - page 49

    Deleting a CID Record To delete the record shown in the display , press the DELETE softkey twice. Deleting All Call Records This feature allows you to clear all CID records at once. 1. While viewing a CID record, press and hold the DELETE softkey PRESS DELETE AGAIN CLEAR ALL CALLER ID shows in the display . Dialing Back When reviewing CID records, ...

  • RCA 25825 - page 50

    Memory Log and Phone Book (Directory) Memory Y ou may store data in the Phone Book Directory or an MEMORY LOG (16 buttons located to the right of the number pad on the base). The Phone Book and each MEMORY LOG stores up to 2 1 characters and 32 digits. Storing a Number and Name in Memory NOTE: T o cancel the storing procedure at any time, press EXI ...

  • RCA 25825 - page 51

    Reviewing Phone Book (Directory) Memory stored in alphabetical order). 2. Use the VOL (+ or -) buttons to scroll up or down through the phone book memories, or use the touch tone pad on your phone to enter the corresponding letters for the memory you want to review . For example, press the 5 key to display phone book memories that start with the le ...

  • RCA 25825 - page 52

    6. Press the DIR button to store the redial number in the Phone Book memory or press an MEMORY LOG button (1-16) to store the redial number in that memory location. Storing a P ause in Memory Press the #PAUSE button twice to insert a pause in the dialing sequence of a stored telephone number when a pause is needed (for example, when you must dial a ...

  • RCA 25825 - page 53

    Clear All Memories 1. Press the Menu softkey while in standby mode. 2. Use the VOL (+ or -) buttons to scroll up or down to PHONE OPTIONS. 3. Press the Select softkey . 4. Use the VOL (+ or -) buttons to scroll up or down to CLEAR ALL MEMORIES. 5. Press the Select softkey . 6. Use the VOL (+ or -) buttons to scroll up or down to Y es or No, No is t ...

  • RCA 25825 - page 54

    Dial by zero After the Auto-Attendant answers the call and plays the greeting it will prompt “If you known the extension of the person you are trying to reach, please dial it now” and wait your input of the extension number. If there is no input , the unit will prompt “For dial by Name directory, press 4.” Then the unit will prompt "Fo ...

  • RCA 25825 - page 55

    sure the Network cords are not damaged. • Make sure the hook switch pops up when the handset is lifted. Try to P ower reset the phone or IPBX and wait it returns to ID found. Y ou cannot be heard by the other party • Make sure the handset or headset cord is inserted properly and securel y . • Make sure the MUTE feature is not turned on. Phone ...

  • RCA 25825 - page 56

    General Product Care To keep your telephone working and looking good, follow these guidelines: • Avoid putting the phone near heating appliances and devices that generate electrical • DO NOT expose to direct sunlight or moisture. • Avoid dropping the handset, as well as other rough treatment to the phone. • Clean the phone with a soft cloth ...

  • RCA 25825 - page 57

    Warranty Limited Warranty What your warranty covers: • Defects in materials or workmanship For how long after your purchase: • T wo years, from date of purchase What we will do: • Provide you with a replacement unit. The exchange unit is under warranty for the remainder of the original product’s warranty period. How you get service: • Loc ...

  • RCA 25825 - page 58

    58 • Products purchased or serviced outside the USA • Acts of nature, such as, but not limited to lightning damage Product Registration: • Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be neccessary . The return of the card is not required for warranty covera ...

  • RCA 25825 - page 59

    ...

  • RCA 25825 - page 60

    Visit the RCA web site at www .rca4business.com Please do not send any products to the Oregon address listed in this manual or on the carton. This will only add delays in service for your product. Beaverton, Or 97 005 RCA is a trademark of RCA Trademark Management S.A., Used under license. © 20 1 0. All rights reserved. Model: 25825 T0009068(REV.0 ...

Produzent RCA Kategorie Telephone

Dokumente, die wir vom Produzenten des Geräts RCA 25825 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen RCA
- Bedienungsanleitungen 25825
- Produktkarten RCA
- Informationsbroschüren
- oder Energieetiketten RCA 25825
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung RCA 25825.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen RCA 25825, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen RCA 25825. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts RCA 25825 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts RCA 25825, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von RCA 25825 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von RCA 25825 verständlich ist.

Eine gänzliche Bedienungsanleitung von RCA sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von RCA 25825 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von RCA 25825 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich RCA 25825, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts RCA 25825 - die uns die ersten Schritte während der Nutzung von RCA 25825 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit RCA 25825 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von RCA 25825 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich RCA 25825?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit RCA 25825 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit RCA 25825 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)