-
Graco Inc. RTX 1250 - page 1
311768B Operation Interior T e xture Spra y er s R TX 900 & R TX 1250 For W ater-Based Materi als Only Models: 254974 & 254975 70 psi (0.49 MP a, 4.9 bar) Maximum Fluid Working Pressure Related Manuals Import ant Safety Instructions. Read all warnings and instr uctions in this manual. Sav e these instr uctions. 311777 311772 Model 254975 Sh ...
-
Graco Inc. RTX 1250 - page 2
Warnings 2 Wa r n i n g s The f ollowing are general w arnings related to the setup , use, g rounding, mainten ance and repair of th is equipment. Additional, mo re specific warnings ma y be f ound through out the body of this manual where applicab le. Symbols appearing in the body of the man ual ref er to these genera l warnings. When th ese symbo ...
-
Graco Inc. RTX 1250 - page 3
Warnings 3 Burn Hazard Equipment surf aces and fluid that’ s heate d can become v ery hot dur ing opera tion. T o a void se vere b urns, do not touch hot fl uid or equipment. W ait until equipment/flu id has cooled completely . Electric Shoc k Hazar d T o reduce the r isk of electr ic shock: • Be sure spra yer is adequa tely grounded th rough e ...
-
Graco Inc. RTX 1250 - page 4
Warnings 4 CA UTION • W ater or material remaining in unit when temper atures are belo w freezing ca n damage motor and/or delay pump star tup. Do not allow unit to freeze . • Bef ore adding material or starting unit in cold weather , run warm water through pump . T o ensure water and mat erial are completely dr ained out of un it: 1. Remov e m ...
-
Graco Inc. RTX 1250 - page 5
Component Identi fication 5 Component Identification M D F A G C L Model 254975 Sho wn E K U T V B S Y cc R P bb N H J ti8939a W Item Component Item Component A Handle N Burp Guard B T oolbo x P Material/Air Hose C P ow er Cord (120V , 25 ft) Q Accessories Bag D Side Pump Access Panel (R T X 1250 O nly) R Mater ial Thickness Gaug e E RotoFle x ™ ...
-
Graco Inc. RTX 1250 - page 6
Preparation 6 Preparation Pressure Relief Procedure T o reduce risk of injur y , follo w this procedure whene v er y ou see this symbol throug hout this manual, Also , perf or m this procedure whene ver you : • Stop spra ying • Check or repair a ny par t of this system • Install or clean spra y nozzle 1. T ur n P ower Switch OFF . 2. T rigger ...
-
Graco Inc. RTX 1250 - page 7
Setup 7 Setup T e xture Spra ying (material supplied from unit) 1. Connect air hose and m ater ial hose to spray er a ir and material hose out lets. 2. Open air valv e. 3. Connect ai r hose to gun. 4. Connect material hose to gun. 5. Mak e sure b urp guard is installed, Cautio n , page 3. 6. Install spra y nozzle. See Recommended Nozzle Selection C ...
-
Graco Inc. RTX 1250 - page 8
Setup 8 9. T urn power switch ON. 10. Close gun air v alv e. 11. P oint gun into waste buck et and pull trig ger to pump water t hrough the system. Cont inue to trigger gun until material hopper is empty . 12. Add pr e-mixed te xture mix to m ater ial hoppe r . See Mixing Mate rial, page 10. 13. Contin ue to trigger gun and spra y into wast e buc k ...
-
Graco Inc. RTX 1250 - page 9
Setup 9 6. T ur n hopper gun/spr a y gun selector s witch to HOP- PER GUN. 7. Open gun air valv e. 8. T urn power switch ON. 9. T o achiev e uniform spray patter n, adjust air valv e and flo w adjustment n ut on gun. If y ou do not achie ve the desired spr a y pattern, change nozzles (see page 11). ti9220a ti8528a ti9222a ti8532a ...
-
Graco Inc. RTX 1250 - page 10
Mixing Material 10 Mixing Material Dry Mix - 40 lb (18 kg) ba g 1. Carefully mix te xture material and water according to manuf acturer instructions on bag. 2. Agitate to mix, using a ha lf-inch, variable speed drill with mixing paddle , to a smooth, lump-f ree consis- tency . 3. Allow ceiling te xture to set for at least 15 min utes. Then remix pr ...
-
Graco Inc. RTX 1250 - page 11
Spray Techniques 11 Spra y T echniques Recommended Nozzle Selection Char t 1 Control air volume with gun air v alve. 2 F or more material v o lume try a larger nozzle. Adjusting the System Sufficient fluid ou tput (v olume and pressure) and good atomization is a balance of atomo zing air , material thickne ss/material flow an d nozzle selection. Ac ...
-
Graco Inc. RTX 1250 - page 12
Shutdown and Cleanup 12 Shutdo wn and Cleanup T e xture Spra ying (8-10 gallon Ma terial Hopper) When you hav e finishe d spra ying: 1. Open gun air valv e. 2. Mak e sure hopp er gun/spr a y gun selection s witch is tur ned to SPRA Y GUN. 3. T urn power switch ON. 4. Close gun air v alv e. 5. T r igger gun into b ucket un til most of te xture mix i ...
-
Graco Inc. RTX 1250 - page 13
Shutdown and Cleanup 13 Removing Ma terial Hopper Fr om Spray er: The material hopper can be rem ov ed for cleaning . T o remov e material hopper : 1. Loosen botto m fitting. 2. Lift mater ial ho pper straight up, off unit. 3. Plug opening on bo ttom of material hopper with y our hand. 4. T ake hoppe r to cleaning ar ea. T o Reassemble: 1. Place ma ...
-
Graco Inc. RTX 1250 - page 14
Troubleshooting 14 T r oubleshooting Prob lem C ause Solution Spra yer won’t run P ower s witch not on T ur n s witch on. No pow er at wall outle t Chec k outlet by plugging in another appliance . If appliance does not work, try another outlet. Wrong size ge nerator Use a 3500 wa tt or larger gener ator . Ref er to Gener ator Require ments , page ...
-
Graco Inc. RTX 1250 - page 15
Troubleshooting 15 Speed of application slo w or slow er Material too thick Thin material. Nozzle too small Change nozzles to a larger siz e. See Recommended Nozzle Selection Char t, page 11. T oo much air being used. P ar tially close gun air v alve to r educe air flow . Pump hose worn Rep lace hose. Plugged or dirty gun Relie ve Pressure , page 6 ...
-
Graco Inc. RTX 1250 - page 16
Technica l Data 16 Te c h n i c a l D a t a *Measured while sp ra ying at 1 m. **Measured per ISO- 3744 Main unit pow er requirement s 120 V ac , 60 Hz, 15A, 1 phase Maximum fluid wor king pressure 70 psi, (4.9 bar) Maximum air w orking pressure 50 psi, (3.5 bar) Compressor specifications Univ ersal motor thermally protected, oil-less Compresso r a ...
-
Graco Inc. RTX 1250 - page 17
Graco Warra nty 17 Graco W arranty Graco warrants all equipment ref erenced in this document which is manufactured b y Graco and bearing its na me to be free from defects in material and workmanship on the date of sale to the or iginal pu rchaser for use . With the e xception of any special, ex tended, or limited warranty pub lished by Graco , Grac ...
-
Graco Inc. RTX 1250 - page 18
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311768 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 14 ...
Haben Sie eine Frage bezüglich Graco Inc. RTX 1250?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Graco Inc. RTX 1250 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Graco Inc. RTX 1250 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.