Deutsch dropdown-ico

Bedienungsanleitung Acer RA19WAANU

36 Seiten 5.79 mb
Download

Zur Seite of 36

Summary
  • Acer RA19WAANU - page 1

    Model ID:RA19W AANU Published by Wistron Corporation Printed in T aiwan © All rights reserved Subject to modification 04th-Sept.-2008  DBG DPBU II DBG DPBU II T able of Contents Important Safety Notice------------------------------------------------------------------------------------- 01 01. Product Specification---------------------- ...

  • Acer RA19WAANU - page 2

    Product Announcement: This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. V ender assumes no liability express or implied, arising out of any unauthorized modification of design or replacing non-RoHS parts. Servic ...

  • Acer RA19WAANU - page 3

    1.1 SCOPE This document defines the design and performance requirements for a 19W inch diagonal , flat panel monitor .The display element shall be a WXGA(1366X768) resolution TFT-LCD (Thin Film Transistor Liquid Crystal Display).16.7M color images are displayed on the panel.Video input signals are analog RGB (0.7Vp-p). When the systemis powered-on ...

  • Acer RA19WAANU - page 4

    1. Product Specification (continued) 1.3.1.3 Audio Jack (option) This jack shall connect the audio input from host computer. 1.3.2 Video Input Signals Video Input Signal Ranges 1.3.2.1 Video Signal Amplitudes The three video inputs consist of Red ,Green , and Blue signals, each with its own coaxial cable terminated at the monitor. These video signa ...

  • Acer RA19WAANU - page 5

    1.3.2.5 Sync Signal Loading TTL input loading shall be equivalent to one TTL input load. When logic 0 is asserted by a sync input , the maximum current source from any single monitor sync input to the driver is 1.6 mA .When logic 1 is asserted , the maximum current source from the driver to any single monitor sync input is 400 uA . 1.3.2.6 Abnormal ...

  • Acer RA19WAANU - page 6

    1.3.5 Controller Requirements 1.3.5.1 General Requirements The monitor shall include a controller capable of converting the analog RGB signal from a standard SXGA resolution video controller in the CPU to a signal which can be displayed on the panel. The controller will include a PLL, A/D converters, LVDS transmitter and other circuitry necessary t ...

  • Acer RA19WAANU - page 7

    1.3.8 Display Communications Channel The monitor assembly shall provide a display communications channel that conforms to VESA DDC2Bi hardware requirements. This configuration shall contain the 128-byte EDID file as specified by VESA EDID standard.The monitor should not write to the EDID file for the first two minutes of operation following power-u ...

  • Acer RA19WAANU - page 8

    1.4.5.5 Defect T erminology T able 3 gives the descriptive terms used in classifying defects. 1.5 Optical Characteristics Depends on the LCD supplier's spec. Details refer to QA Inspection Spec. 1.4.5.6 Smudges, Streaks and Smears When viewing the panel oriented so as to maximize reflected light , there shall be no visible smudging , streaking ...

  • Acer RA19WAANU - page 9

    2.1 MAIN OSD MENU Outline: The description for control function: 2 OSD Menu The description for control function: Ma i n Me nu Ic o n Sub Me nu Ic o n Sub Me nu Ite m D escr i p t i on Ad j ust m ent Range Re s et V al ue N/ A W a r m Set t he co l or t em p er at ure t o wa r m wh i t e . N/ A N/ A Co ol Set t h e col or t em per at ure t o coo l ...

  • Acer RA19WAANU - page 10

    2. OSD Manu (continued) 9 Go to cover page ACER X193HQ ...

  • Acer RA19WAANU - page 11

    3.1 Packing Exploded Diagram 3. Exploded Diagram 10 Go to cover page ACER X193HQ ...

  • Acer RA19WAANU - page 12

    3.2 Product Exploded Diagram 3. Exploded Diagram (continued) 11 Go to cover page ACER X193HQ ...

  • Acer RA19WAANU - page 13

    S4 S5 S3 S2 S1 Use a Phillips-head screwdriver screwed the No.1~2 screws till that interface board and bracket chassis base firmly attached. (No1~2 screw size=M3x6; T orque=9~10KGFxCM). Use a Phillips-head screwdriver screwed the No.1~4 screws till that power board and bracket chassis base firmly attached.(No1~3 screw size=M3x6; No4 screw size=M4x8 ...

  • Acer RA19WAANU - page 14

    Plug 2 lamp cables to the connectors of inverter board. T ake lamp cables out from the holes shown as the photo. Use a Hex-head and screwdriver screwed the DVI and D-SUB connectors (No.1~4 Hex Nut screws Size=M3x8;T orque=6.5 KGFxCM). 6.5 ±0.5 ±0.5 Phillips-head T orque= KGFxCM). T ake a key function board to hook with front bezeland connect to k ...

  • Acer RA19WAANU - page 15

    Stick Vista and TC003 label on the correct position the same as below photo T ake a LDPE+EPE bag to cover the LCD monitor . T ake two cushion foams; one is held the left side of LCD monitor , and another is held the right side. . Put accessories of stand, DVI cable, and user’s manual ,power cable on specific positions as photo below. Move previou ...

  • Acer RA19WAANU - page 16

    4. Assembly and Disassembly Procedures (continued) Use a Phillips-head screwdriver unscrew 4 screws to release the stand base. (No1~4 Screw Size=M4x10; T orque=12 KGFxCM). ±1 Disassemble the stand cover . P ut returned unit on a protective cushion,then remove LDPE+EPE bag. T ear off tapes to remove the screen protector card then turn over the LCD ...

  • Acer RA19WAANU - page 17

    Put the dissembled monitor closed to by myself W edge your finger between the front bezel and the panel, then pry up on the front bezel to disengage the locking mechanism. Insert steel rule between panel and front bezel .Using properly force to let the locking mechanism of front bezel and rear cover separated Separating all of the locking mechanism ...

  • Acer RA19WAANU - page 18

    Unplug 2 lamp cables Use a Hex-head screwdriver unscrewed 4 screws to release the DVI and D-SUB connectors (No1~4Hex Nut screws Size=M3x8;T orque=4.5~6.5KGFxCM). Disconnect the FFC cable to the connector of panel. Use finger to push the lock according to arrow direction then take out the FFC cable Hold one side of down side that had been separated ...

  • Acer RA19WAANU - page 19

    Use a Phillips-head screwdriver unscrewed the No.1~4 screws to disassemble the power board. (No 1~3 screw size=M3x6; No 4 screw size=M4x8; T orque=9~10KGFxCM). Disconnect all of the cable Use a Phillips-head screwdriver unscrewed the No.1~2 screws to release the interface board. (No1~2 screw size=M3x6; T orque=9~10KGFxCM). Examine the panel surface ...

  • Acer RA19WAANU - page 20

    5. T roubleshooting Does OSM display when you push PROCEED buttom. Yes No Proceed "No OSM display" section. Check if the sync signal from computer is output and if the video cable is connected normally. OK Proceed "checking the resolution change IC movement" section. NG Input the sync signal of computer , or change the cable. Wh ...

  • Acer RA19WAANU - page 21

    5. T roubleshooting (continued) 5.2 Nothing displays on the screen (Screen is black and colour of LED is blue.) Is backlight lit? Refer "Checki ng the backlight unit" section" OK NG Does computer output RGB video signals? OK Check OSM menu is displ ay on screen w h e ny o up u s ht h e" P R O C E E D "k e y . Proceed " ...

  • Acer RA19WAANU - page 22

    5. T roubleshooting (continued) 5.2 Nothing displays on the screen (Screen is black and colour of LED is blue)continued Continue Check the 5V power supply for P305 pin 1,2,3. OK Check the I301 pin2 if voltage is 3.3V OK Failure P oint 1) Printed wir e between R 311 pin3, R410, R412, I307 pin1 is failure. . 2) Q311 is failure. NG Check if the voltag ...

  • Acer RA19WAANU - page 23

    5. T roubleshooting (continued) 5.3 Checking the back light unit Is +22V supplied to inverter PWB ? (by the power board) OK NG Failure Point 1) Power board of Inverter part failure . Check the BKLT_EN signal of the DC input P301 pin 1 at TTL high level. OK NG Failure Point 1) printed wire broke between P301 pin1, R303 and I305 pin 88. 2) I305 is fa ...

  • Acer RA19WAANU - page 24

    5. T roubleshooting (continued) 5.4 Abnormal screen for VGA Check the R, G, B video signal from computer input on P302 of video connector. OK NG Failure Point 1) No R, G, B video signals output from host computer, check computer. 2) Video signal cable disconnection . Check the R, G, B input video signals on I305 pin12, 14, 16 respectively that thei ...

  • Acer RA19WAANU - page 25

    5. T roubleshooting (continued) 5.5 Abnormal screen (For the DVI) Check the DVI video signal from computer input on P303 of DVI-I video connector. OK NG Failure Point 1) No DVI video signals output from host computer, check computer . 2) DVI Video signal cable disconnection . Check the DVI input video signals on I305 pin 2,3,4,5,6,7,47,48 respectiv ...

  • Acer RA19WAANU - page 26

    5. T roubleshooting (continued) 5.6 Abnormal OSM display adjust problem Check the input TTL level whether was changed when pressed function keys on the P304 pin3, 5 (normal is high level, when push buttom, generat ed low level plus ) OK NG Failure Point 1) Function key wire disconnection . 2) Function key wire i s failure . 3) Function key board is ...

  • Acer RA19WAANU - page 27

    5.7 Abnormal plug and play operation for VGA Confirm the host computer supplies DDC 2B mode. OK NG Failure Point The host machine is not communicatiog in DDC2B mode. Check the voltage on Q307 pin1 that is power DC 3.3V. OK NG Failure Point 1) Printed wire broke between Q307 pin3,D325 and P302 pin9 2) R369,R372,R363 is short or open. 3) D325 is fail ...

  • Acer RA19WAANU - page 28

    5.8 Abnormal plug and play operation (For the DVI) Confirm the host computersupplies DDC 2 mode. OK NG Failure Point The host machine is not communicatiog in DDC 2 mode. Check the voltage on Q 307 pin1 that is power DC 3.3 V. OK NG Failure Point 1) Printed wire broke between VR307 pin3,D325 and P303 pin14 2) R361,R372,R363 is short or open. 3) D325 ...

  • Acer RA19WAANU - page 29

    5.9 Checking the interface circuit of sync signal 5.9.1 Checking the control circuit of horizontal sync pluse Check the horizontal sync signal on P302 pin13 TTL level. OK NG Failure Point Video cable is failure. Check the horizontal sync signal on I 308 pin9 TTL level. OK NG Failure Point 1) Printed wire broke between P302 pin13 and I308 pin9. 2) F ...

  • Acer RA19WAANU - page 30

    5.10 Checking the resolution change IC movement Check +3.3V supply on I305 pin41,I308 pin1,46. OK NG Proceed " Checking the DC/DC converter circui t" sect ion. Check +1.8V supply on I308 pin 19,17,40. OK NG Proceed " Checking the DC/DC converter circui t" sect ion. Check X300 24MHz clock input to I305 pin 15 and 16 at TTL level. ...

  • Acer RA19WAANU - page 31

    Check the 5V is output from P301 pin 5,6 OK NG Failure Point 1) Power wire disconnection. 2) Power board is failure . Check the 5V is input to I301 pin3. OK NG Failure Point 1) Printed wire broke between P301 pin 5,6 and I308 pin3. Check the 3.3V is output from I301 pin2, 4. Failure Point I301 is failure or C303,C304 short. OK NG Check the 3.3V is ...

  • Acer RA19WAANU - page 32

    6.2 Realtek F/W Configuration: Step-1 Launch the utility of “ ” DebugT ool_V6.2.exe Step-3Select ISP icon. Step-4 Follow up the red square indication Select “both”,”Checksum”,”Auto”,”Page Erase”, Select “21” for Extend size. Connect VGA cable between monitor and kit Connect USB and VGA cable between PC and kit Step-2 Select ...

  • Acer RA19WAANU - page 33

    Step-6Press button The screen will show “P ASS” Step-5 Select “64K” icon to load firmware image. There are two HEX files. Y ou only need to select “64K” to choose “X203H_AAS_F001-EMEA.hex” and “X203H_AAS_F001-EMEA_Extend.hex” will be loaded in “64~96” automatically . Check firmware version Turn off the power,then press force ...

  • Acer RA19WAANU - page 34

    PRINTER PLUG DVI EXTENDING SOCKET USB A PLUG D-SUB PLUG DVI EXTENDING SOCKET USB A SOCKET 1 Writing EDID Procedure Hardware Configuration: 1.)Connect the PRINTER PLUG of DDC FIXTURE with the printer port of Desktop PC. (Refer to figure 1) 2.)Plug USB A PLUG of DDC FIXTURE to USB socket of Desktop PC (Refer to figure 2) 3.)Extend the DVI cable on DV ...

  • Acer RA19WAANU - page 35

    4. Choose "WRITE" from menu then select "Scan S/N And Write EDID And Test DDC” 5. Key in series number(22 characters) in the input column and below empty column. Press write button after key in S/N 6. When EDID was written successfully that will show below message on the screen Go to cover page 34 7. Writing EDID Process (continued ...

  • Acer RA19WAANU - page 36

    8. BLOCK DIAGRAM PCB No. LCD Flat Panel Interface Board Flat Panel Controller DDC , Interface Board DC to AC Inverte r () Option AMP Audio 1W 2 * Speaker () Option Function Key Boar d AC IN - Host Computer Audio Source AC to DC Adapte r Audio line input Video Signal input DDC & Function key input DC 5V Inverter contro l Panel date control DC po ...

Produzent Acer Kategorie Computer Monitor

Dokumente, die wir vom Produzenten des Geräts Acer RA19WAANU erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Acer
- Bedienungsanleitungen RA19WAANU
- Produktkarten Acer
- Informationsbroschüren
- oder Energieetiketten Acer RA19WAANU
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Acer RA19WAANU.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Acer RA19WAANU, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Acer RA19WAANU. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Acer RA19WAANU ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Acer RA19WAANU, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Acer RA19WAANU hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Acer RA19WAANU verständlich ist.

Eine gänzliche Bedienungsanleitung von Acer sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Acer RA19WAANU bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Acer RA19WAANU befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Acer RA19WAANU, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Acer RA19WAANU - die uns die ersten Schritte während der Nutzung von Acer RA19WAANU erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Acer RA19WAANU hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Acer RA19WAANU im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Acer RA19WAANU?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Acer RA19WAANU nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Acer RA19WAANU hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)