Bedienungsanleitung JBL GTS300

16 Seiten 0.21 mb
Download

Zur Seite of 16

Summary
  • JBL GTS300 - page 1

    either subwoofer or component speakers in a bi-amplified system, or conventional full-range speakers in simpler systems. The GTS300 and 600 also include preamp-level outputs which can provide either full-range, high-pass or low-pass signal to drive additional amplifiers. This lets you build systems of virtually any design without requiring a separa ...

  • JBL GTS300 - page 2

    2 before disconnecting the battery! 2. Run a minimum A WG #8 power cable complete with a 40 amp fuse (not included) for the GTS300 or an A WG #6 or A WG #4 cable with an 80 amp fuse for the GTS600 directly from the positive + 12V battery terminal to the disir ed amplifier location. Keep the fuse to within 6” of the battery terminal, and before th ...

  • JBL GTS300 - page 3

    9. Fuse – 40 Amp A TC type fuse for the GTS300 and two 40 amp fuses for the GTS600. 10. Gain Control – Use this contr ol to adjust the input sensitivity of the amplifier . See the “Adjusting the Gain” section for tips on proper setup. 11. Preamp-Output Crossover Switch – This switch controls the built-in crossover that is directed to the ...

  • JBL GTS300 - page 4

    3. System Design Using the GTS300 or GTS600: 3.1 Speaker Requirements When used in the non-bridged mode the GTS300 or GTS600 can easily drive 2 ohm speaker loads. When only one speaker is connected to each channel, virtually any conventional speaker may be used. When the GTS300 or GTS600 is in bridged mode, the combined impedance of the speaker (or ...

  • JBL GTS300 - page 5

    components is extremely important for proper performance and long term reliability . All wiring connections should be made either by soldering with heatshrink tubing insulation or with high quality crimp type insulated connectors installed with a good crimping tool. Soldering crimp connections is recom- mended to further enhance connection reliabil ...

  • JBL GTS300 - page 6

    5. Internal Adjustments Speaker -Level Input Impedance Adjustments The speaker level inputs of the GTS300 and GTS600 come factory set with 100K ohm input impe- dance. This will provide the lowest distortion operation from the speaker outputs of most modern head units by reducing the power the amplifier in the head unit must deliver to practically n ...

  • JBL GTS300 - page 7

    Regardless of whether you build or buy it, the necessary resistor network has the following configuration: Custom “Chip” Construction • Each resistor in the package has the same value. • If you kvow the crossover frequency you want, you can calculate the resistor value necessary by solving the following equation: Resistor 2,500,000 V alue = ...

  • JBL GTS300 - page 8

    6. Input Gain Adjustment Before operating the GTS300 or GTS600, recheck all wiring connections to make sure they are correct and secure. Be sure that a fuse (40 amp for GTS300 and two 40 amp fuses for the GTS600, not included) is installed in the +12V line near the battery . Reconnect the negative ground (-) terminal of the battery . Make sure that ...

  • JBL GTS300 - page 9

    7. T ypical Applications The following diagrams show the most common basic system configurations of the GTS300 and GTS600. A combination of one or more of these “building blocks” may be combined to form elabo- rate system designs. 9 ...

  • JBL GTS300 - page 10

    10 L– R+ – + L– R+ – + L– R+ – + Preamp or Speaker-Level Input L R 2 or 4-Ohm Full-Range Speakers L– L+ – + R– R+ – + L R Front Rear 4-Ohm Subwoofer Stereo Subwoofers may be used by configuring Amp B as shown in Application #1 . Application 1 Stereo Full-Range or Subwoofer Operation Preamp or Speaker-Level Input L R 2 or 4-Ohm F ...

  • JBL GTS300 - page 11

    Simultaneous Stereo-Mono Connection Diagrams 11 L– L+ L L L R R R – + L– R+ – + R– R+ – + 2 or 4-Ohm Full-Range Speakers 4-Ohm Subwoofer Amp Crossover Input Mode Preamp Switch Switch Output Crossover A High Pass Stereo Flat B Low Pass L + R Doesn't Matter Speaker Output GTS300/600 A GTS300/600 B Application 4 Bi-amplified System Us ...

  • JBL GTS300 - page 12

    8. In Case of Difficulty Power -on light does not come on Power light is on, but no sound is heard from some or all of the speakers • Head unit not on; turn the head unit on. • Ground wire is disconnected or defective; check for continuity with an ohm-meter between the amplifier’ s ground terminal and a know chassis ground point. • Battery ...

  • JBL GTS300 - page 13

    Power On light is blinking, indicating a fault condition, and sound is intermittent or off Alternator whine through the audio system with the engine running Bass output from speakers too low • Defective GTS300 or GTS600; If ther e is audio signal present at the input of the amplifier and there is no output, the GTS300 or GTS600 may be defective. ...

  • JBL GTS300 - page 14

    9. Specifications Specifications Power Output (10Hz -50kHz, 14.4V Battery V oltage Signal to Noise Ratio Fr equency Response Damping Factor Line Level Input Sensitivity (For Rated Power) Line Level Input Impedance Speaker Level Input Impedance Speaker Level Input Sensitivity Preamp Output Sensitivity Minimum Speaker Impedance Single Ended (Non-Brid ...

  • JBL GTS300 - page 15

    15 Specifications Power Requirement Fuse Size Size (L x W x H) W eight Speaker Level Input Mating Connector GTS300 11 to 16V DC Negative Ground 40 Amp A TC T ype Fuse 13 1/4”x 9 1/4”x 2” (337 mm x 235 mm x 51 mm) 10 lbs 8.5 oz (4.8 Kg) Molex Mini-Fit Jr . # 39-01-2045-P Metal Pins: 39-00-0039 GTS600 11 to 16V DC Negative Ground 40 Amp A TC T ...

  • JBL GTS300 - page 16

    16 DECLARA TION OF CONFORMITY W e, Harman Marketing Europe a/s Kongevejen 194B DK-3460 Birkerød DENMARK declare that the product described in this owner’ s manual is in compliance with technical standards: EN 55020, EN 6.1988, Accredited test laboratory: MIKES PRODUCT SERVICE GmbH Ohmstrasse 2-4 D-94342 Strasskirchen GERMANY , (date tbd) Steen M ...

Produzent JBL Kategorie Home Theater System

Dokumente, die wir vom Produzenten des Geräts JBL GTS300 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen JBL
- Bedienungsanleitungen GTS300
- Produktkarten JBL
- Informationsbroschüren
- oder Energieetiketten JBL GTS300
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung JBL GTS300.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen JBL GTS300, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen JBL GTS300. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts JBL GTS300 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts JBL GTS300, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von JBL GTS300 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von JBL GTS300 verständlich ist.

Eine gänzliche Bedienungsanleitung von JBL sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von JBL GTS300 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von JBL GTS300 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich JBL GTS300, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts JBL GTS300 - die uns die ersten Schritte während der Nutzung von JBL GTS300 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit JBL GTS300 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von JBL GTS300 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich JBL GTS300?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit JBL GTS300 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit JBL GTS300 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)