Deutsch dropdown-ico

Bedienungsanleitung Vespa 150

31 Seiten Betrifft nicht
Download

Zur Seite of 31

Summary
  • Vespa 150 - page 1

    ...

  • Vespa 150 - page 2

    STABILIMEN TO DI PONTEDERA UFFICIO TECNICO SER IE Dis. 88356 M 2 a EDIZIONE, 600016102 Printed in Italy Fig. 1 – Vespa 150 ...

  • Vespa 150 - page 3

    NOTICE To keep your VESPA in perfect running order and not to invalidate the guarantee offered by the co ntract, it is advisable to entrust repairs o nly to retailers or authorized service stations. Demand original Piaggio spare parts exclusively. All PIAGGIO s pares are made of the same material, have undergone the same machining steps and inspect ...

  • Vespa 150 - page 4

    The descriptions and illustrations in this booklet are not to be taken as binding on the Manufacturer. The essential features of the model desc ribed and illustrated herein remaining unaltered, the PIAGGIO F i rm reserv es therefore the right to carry out at any moment, without being obliged to bring this booklet up-to-date in due course, modificat ...

  • Vespa 150 - page 5

    TECHNICAL DATA Fig. 2 & 3: - Stamping on frame (1) – Stamping on engine (2) ...

  • Vespa 150 - page 6

    Fuel consumption (CUNA Standards) 2.2 liters to 100 Km (107 miles per USA gal ; 128 miles per imp. gal). Max speed (CUNA) 85 Km "h (53 m.p.h. ) Carrying capacity 2 persons and 10 Kg. (22 Ibs) of l uggage. Range 360 Km (225 miles) Wheel base 1180 mm (46.4" ) Handlebar width 710 mm (27.9") Max length 1745 mm (68.7") Max height 102 ...

  • Vespa 150 - page 7

    Fig. 5 - Ign ition diagram 1. Ignition coil in flywheel magneto - 2. External H. T. coil - 3. Rotor cam - 4. Breaker - 5. Condenser - 6. Sparkplug - 7. Engin e cut-out on sw itch. Such numbers and prefixes identify the V espa as p rescribed by law and are repeated on the test card and other doc uments of the Vespa. They must be quoted when ordering ...

  • Vespa 150 - page 8

    ENGINE Single h orizontal cylinder, two-stroke, with deflector pist on and rotary valve, i. e.: fuel mixture flow to the cylinder is controlled by the r otation of a crankweb (see Fig. 4). The engine works on a 2% gasoli ne-oil mixture. Bore 57 mm (2.24") Stroke 57 mm (2.24") Displacement 145.45 cc ( 8.88 cu.in ) Compression ratio 6.8 to ...

  • Vespa 150 - page 9

    Fig. 6 - Feeding circuit 1. Fuel cock lever wi th sediment trap: A) Reserve, B) Open, C) Closed - 2. Flo at - 3. A ir cleaner with carburettor - 4. Air vent for starter device - 5. Set screw for throttle slide - 6. Th rottle slide - 7. Air vent for main jet - 8. Hole on mixer top - 9. Mixer - 10. Main jet - 11. Idling jet - 12. Air vent for idli ng ...

  • Vespa 150 - page 10

    with that of the clutch, o n left hand side of handlebars (see Fig. 8). Starting. By means of kick-starter, night hand side of scooter. The multiple gear and consequently the engine is set in motion through a ratchet sec tor and a gear by operating the kick-starter. Cooling effected at all engine speeds by a centrifugal fan (see Fig. 7). Muffler. E ...

  • Vespa 150 - page 11

    Fig. 8 VESPA controls 1. Gear change tw istgrip with clu tch control lever - 2. Fron t brake lever - 3. Throttle control grip - 4. Light and di p swi tch - 5. Fron t brake shoes - 6. Rear brake pedal - 7. Kick-starter - 8. Gear shifter - 9. Rear brake shoes - 10. Clutch - 11. Carburettor, air cleaner - 12. Starter d evi ce control lever - 13. Fu el ...

  • Vespa 150 - page 12

    Steering column, suspension and wheels. The ste ering column bears the handlebars, clamped on its top end, and the front wheel swinging hu b, pivoted at its bot tom en d through a stub axle (see Fig. 9). Front suspension with variable rate coil sp ring and double action hydraulic damper. Rear suspension: s winging bracket for engine a nd rear wheel ...

  • Vespa 150 - page 13

    Steering lock. A su itable security lock is arranged on the frame, near the handlebars. Turning the key anticloc kwise and the handlebars to the left, the lock engage s th e lugs welded on the steering column, so that the machine can only turn around. Turn the key clockwise for releasing the steering system (see Fig. 10). We re comme nd not to lubr ...

  • Vespa 150 - page 14

    Fig. 11 – Handlebar switch A – Engine cut-out B. Parking lights and speedometer bulb on – C. Lights off – D. Head lamp, tail lamp speedometer bulb on – E. Dip switch – F . Horn button - 7. Main switch Fig. 11A – Cables & harness 1. Flyw heel magneto - 2. External ignition coil - 3. Sparkplug - 4. Low ten sion terminal - 5. Tail la ...

  • Vespa 150 - page 15

    Fig. 12 – Electric wiring diagram 1. Flyw heel magneto - 2. External ignition coil - 3. Sparkplug - 4. Low ten sion terminal - 5. Tail lamp 16V-3W - (. STOP light - 6V-3W) - 7. Main sw itch - 8. Speedometer bulb (6V-0.6W) - 9. Double filament bulb (6V25/25W) - 10. Pilot light 6V-3W - 11. Horn - 12. STOP light switch - 13. Inside view of h ead lam ...

  • Vespa 150 - page 16

    Horn A 0,6 W bulb is provided for illuminating the speedometer dial.The light and dip swit ch unit, with two levers is installed on the right hand side of the handlebars (see Fig. 11 ) ; one of the control levers has three posit ions: - pilot light, tail la mp and speedometer bulb on; - lights off; - head lamp, tail lamp and speedometer bulb on; th ...

  • Vespa 150 - page 17

    Fig. 13 – Pillio n seat, spare wheel and bracket ...

  • Vespa 150 - page 18

    Owing to the simple and rational desi gn of the Vespa scooter, no particular experience is required fo r its operatio n, nor skill ed personnel for its maintenance . The tasks can be carried out by any customer, even unexperienced, by following some general rules, O P E R A T I O N Fuel to be used during and after running-in sho uld be a mixture of ...

  • Vespa 150 - page 19

    - Close the fuel tap, remove sparkplug and action the engine by means of the kickstarter; wipe the plug dry and screw it back. Open the f uel tap and depress the starting lever. Exercise care on re-assembling the sparking pl ug; start screw ing i t by hand at the proper ang le to avoid damaging the cylinder; use the box wre nch just for the last tu ...

  • Vespa 150 - page 20

    Fig. 15 - Drive sys tem I. Gear change twi stgrip c 2. Clutch control lever c 3. Gea r change control cables c 4. G ear shifter c 5. Selector stem c 5. Selector - 7. 1st g ear pinion c 8. 2nd gear pin ion c 9. 3rd gear p, )ion c 10. 4th gear pinion - 11. Main shaft c 12. Cush gear c 13. Clutch. N. B. - Positions 1-2c3-4 o f the gear change tw istgr ...

  • Vespa 150 - page 21

    Fig. 16 - Engin e bonnet removal 1. Engine bonn et blocking lever - 2. Front dowel - 3 Fixing hook - 4. Hooked pivot. For access to the engine , t ake off the engine bonnet: proceed as follows. - Pull the lever « 1 » (Fig. 16) and turn it so as to release it from the bonnet. Then move the bonnet slightly outwards, until front dowel « 2 » diseng ...

  • Vespa 150 - page 22

    Setting the machine in motion . Let the engine idle, lift the clutch and turn the gear change twistgrip (LH.) so that the line engraved on it coincides with the figure «1» (1st gear) engraved on handlebars (see Fig. 15). Now let i n the clut ch gently, while opening the throttle gradually to set the machine in motion. Gear chang e . After reachin ...

  • Vespa 150 - page 23

    Ensure that the spring washers are p resent wh en reassembling w heel: tighten nuts diagonally and eve nly. For removing the inner tube, first deflate it then unscrew the six nuts on t he wheel, so that the two halves of the rim fall apart (se e Fig. 17). Tyre pressu re should be 1.25t11.4 Kg/cmq ( 17.7t20 psi) on rear wheel, and 1 : 1 .1 K g / cmq ...

  • Vespa 150 - page 24

    MAINTENANCE Setting the head lamp. The correct orientation of the main beam can be obtained both horizontally and vertically as follows. Check that both front and rear tyres are in flated to 1 and 2.2 atm (14.2 and 31.3 psi) respecti vely. Fig. 19 - Adjustment of head lamp N. B . - Dimension «0», corresponds to adju stment carried out with driver ...

  • Vespa 150 - page 25

    Before setting the machine in motion Check oil lever in gear box by unsc rewing from the crankcase, the level screw marked « OLIO » (see Fig. 21, No. 1 ). With the scooter standing upright, oil should ju st be about to flow out. After the first 1000 Km (600 miles) Warm up the engine and drain off all oil through the hole provided.Pour some fr esh ...

  • Vespa 150 - page 26

    Every 8000 Km (5000 miles) 1) - Clean the breaker points. In order to avoid ig nition troubles or abnormal running, have the breaker points adjusted at a service station: the gap (see Fig. 20, " A ") should be 0.3 - 0.5 mm (0.011 " to 0.019" ), and t he points should begin to open when the current in the primary i gnition circui ...

  • Vespa 150 - page 27

    Fig. 20 - Breaker points. - A - Max gap: 0.3 - 0.5 mm (0.011-0.019") ...

  • Vespa 150 - page 28

    LUBRICATION CHART PARTS TO BE LUBRICATED TYPE OF LUBRICANT Every 4000 Km (2500 miles) Gear box (Top up oil level ) Esso Motor Oil 30 Brake levers Esso Multi purpose Grease H Front suspension “” Felt of the f l ywheel cam “” Speedometer flex drive and pinion “” Every 8000 Km (5000 miles) Gear box (Change the oil completely) Esso Motor Oi ...

  • Vespa 150 - page 29

    Fig. 21 – Lubrication scheme A: engine lubricated by fuel mixture – 1.: filling hole – 2.: draining hole ...

  • Vespa 150 - page 30

    F A UL-T F I N DI N G When th e machine does not run p roperly, make all inspections and rectifications as explained below. If the suggested remedies are not sufficient to eliminate the trou ble, the customer s hould not try to carry o ut operations pertaining to the retailers, wh o have the neccessary facilities to undertake this wo rk. Locating t ...

  • Vespa 150 - page 31

    INCORRECT RUNNING 1. - Lack of power Muffler outlet pipe carbonised Clean (see page 31). Sparkplug not well screwed into c ylinder head Tighten with 21 mm box wrench. Cylinder head not fitting properly into spi got Set the head properly and tighten on top of cylinder the nuts uniformly 2. - Explosions at muffler and carburettor Replace or clean the ...

Produzent Vespa Kategorie Scooter

Dokumente, die wir vom Produzenten des Geräts Vespa 150 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Vespa
- Bedienungsanleitungen 150
- Produktkarten Vespa
- Informationsbroschüren
- oder Energieetiketten Vespa 150
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Vespa 150.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Vespa 150, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Vespa 150. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Vespa 150 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Vespa 150, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Vespa 150 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Vespa 150 verständlich ist.

Eine gänzliche Bedienungsanleitung von Vespa sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Vespa 150 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Vespa 150 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Vespa 150, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Vespa 150 - die uns die ersten Schritte während der Nutzung von Vespa 150 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Vespa 150 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Vespa 150 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Vespa 150?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Vespa 150 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Vespa 150 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)