Bedienungsanleitung Milnor KURSPK0026

30 Seiten 2.92 mb
Download

Zur Seite of 30

Summary
  • Milnor KURSPK0026 - page 1

    Published Manual Number/ECN: HURSPK0025/99503N • Publishing System: TPAS • Access date: 03/06/03 • Document ECN's: Latest Available Kit Instruction— KURSPK0025 KURSPK0026 PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A. ...

  • Milnor KURSPK0026 - page 2

    Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual. M ost im porta nt, are the publishe d m anual number ( part num ber) /ECN (date code). Ge nerally , when a r eplacem ent manual is furnish ed, it w ill hav e the sam e publis hed m anual num ber, ...

  • Milnor KURSPK0026 - page 3

    MS S M 0 1 1 6 AE / 8 8 0 9 B V È SETTING LI MI T SWITCHES Ê Limit Sw itches—Incl uding Microswit ches— Will Be Damaged If Over-actuated! Any limit switch wi ll be damaged if it bottoms ou t forcefully. This can bend the rotary shaft or damage internal componen ts and may cause the switch to stick in one posi tion either permanentl y or inter ...

  • Milnor KURSPK0026 - page 4

    MSSM0116 AE/8809 BV (1 of 2) È SETTING LI MI T SWITCHES Ê Limit Sw itches—Incl uding Microswit ches— Will Be Damaged If Over-actuated! Any limit switch wi ll be damaged if it bottoms ou t forcefully. This can bend the rotary shaft or damage internal componen ts and may cause the switch to stick in one posi tion either permanentl y or intermit ...

  • Milnor KURSPK0026 - page 5

    Ë Free Position of Rotary Lever —Attach the rot ary lever to the s haft so that, in t he free positi on, the lever is at a right angl e to the direction of rela tive movement bet ween the switch and target (see FIGURE 3). Ë Angle of Switch —Set a plunger swit ch so that the ta rget and plunger m ove parallel t o each other. It will be approxi ...

  • Milnor KURSPK0026 - page 6

    Ë Free Position of Rotary Lever —Attach the rot ary lever to the s haft so that, in t he free positi on, the lever is at a right angl e to the direction of rela tive movement bet ween the switch and target (see FIGURE 3). Ë Angle of Switch —Set a plunger swit ch so that the ta rget and plunger m ove parallel t o each other. It will be approxi ...

  • Milnor KURSPK0026 - page 7

    M S O P 0 9 2 2 AE / 9 8 0 5 A V È PRESS SAFETY FOR INSTALLATION AND SERVICE Ê General Safet y Requirement s (specific warn ings, next page and throughout manual) Incorrect installa tion, neglect ed preventi ve mai ntenance, abuse, and/ or i mproper repairs or changes t o the machine can cause unsafe operation and personal injuries, such as multi ...

  • Milnor KURSPK0026 - page 8

    MSOP09 22AE/98 05AV (1 of 2) È PRESS SAFETY FOR INSTALLATION AND SERVICE Ê General Safet y Requirement s (specific warn ings, next page and throughout manual) Incorrect installa tion, neglect ed preventi ve mai ntenance, abuse, and/ or i mproper repairs or changes t o the machine can cause unsafe operation and personal injuries, such as multipl e ...

  • Milnor KURSPK0026 - page 9

    Ê Danger From an Operating Press CRUSH HAZARD—Devices in and above the press move wi thout warning and can entangle, crush, or sever limbs on contact. ☞ NEVER touch or reach into assemblies i n or above press fr ame unless power is locked OFF and tagged out, and then only for maintenance. ☞ ALWAYS ensure all personnel ar e clear of the press ...

  • Milnor KURSPK0026 - page 10

    HURSPK0026/00186 Page 1 of 21 INSTRUCTIONS FOR 50 KILO AND 60 KILO PRESS S HIM RETRO-FIT These instructions are for adding shims under the main bell air cy linder on 50 kilo and 60 kilo presses. Before be ginning to add shim s below the air c ylinder, it is ne cessar y to fam iliarize yourself w ith all saf ety precaution s in the equ ipment's ...

  • Milnor KURSPK0026 - page 11

    HURSPK0026/00186 Page 2 of 21 8. Replace the coupling onto the shaft on top of the 12 bolt-hole coupler shim. 9. Evenly torque the bolts of the coupling to 25 foot pounds (33.9 Newton meters) (using the cross torque method starting with the four bolts at the split of the coupling) . 10. Manually operate the dome to the up position. 11. Loosen the b ...

  • Milnor KURSPK0026 - page 12

    HURSPK0026/00186 Page 3 of 21 21. Slide as many large shims in the g ap between the base and cross-member as possible. I f a gap re mains betwee n the larg e shims and the ma in bell air cy linder, slide as many smaller shims between the la rge shim and the base of the air cy linder to fill the remaining gap. The last shim may be a tight fit betwee ...

  • Milnor KURSPK0026 - page 13

    HURSPK0026/00186 Page 4 of 21 shaft bearing from the upper cross-member (See Figure 8). 34. Loosen the two bolts that join the shaft-lock to the rig ht-hand uplock jaw. Note the position of the uplock so that it can be reinstalled in the same position. Mark the spacers that are between the t wo bearings so that they may be reinstalled in the same p ...

  • Milnor KURSPK0026 - page 14

    HURSPK0026/00186 Page 5 of 21 Reconnect the left-hand uplock jaw and shaft-lock together using the new lock-nuts provided in the kit and the existing bolts (only hand tighten these bolts at this time) . 44. Replace the lock shaft through the cross-member, being careful to put the correct spacers in the correct position and making sure that the uplo ...

  • Milnor KURSPK0026 - page 15

    HURSPK0026/00186 Page 6 of 21 59. Repeat step ( 49) for the othe r lock seg ments. Recor d all measure ments - they will be used in determining the thickness of the required shims. (Even if most of the measuremen ts are within the spe cified rang e, ea ch lock seg ment will still have to be shimmed. This is because any changes to the shimming of th ...

  • Milnor KURSPK0026 - page 16

    HURSPK0026/00186 Page 7 of 21 clearances (that is, the clearances which should result when the new shim thickness is added or subtracted from the readings obtained earlier) are within the permissible range. 67. When all shim segments have been installed, tighten all bolts (nine for the 50 Kg press, twelve for the 60 Kg press). 68. Energize the pres ...

  • Milnor KURSPK0026 - page 17

    HURSPK0026/00186 Page 8 of 21 Main Bell Air C y linder Bolts Trace Outline of Main Bell Air Cylinder Base on Upper Cross Member Figure 1 15 ...

  • Milnor KURSPK0026 - page 18

    HURSPK0026/00186 Page 9 of 21 Torque To 25 ft-lb ( 33.9 Nm ) Main Dom e Coupling Figure 2 16 ...

  • Milnor KURSPK0026 - page 19

    HURSPK0026/00186 Page 10 of 21 Downlock Shim s Placed on Bed in order to Shim Main Bell Air C y linder Figure 3 17 ...

  • Milnor KURSPK0026 - page 20

    HURSPK0026/00186 Page 11 of 21 One of the Four Main Bell Air Cylinder Bolts Figure 4 18 ...

  • Milnor KURSPK0026 - page 21

    HURSPK0026/00186 Page 12 of 21 Main Bell Air Cylinder Shim s 19 ...

  • Milnor KURSPK0026 - page 22

    HURSPK0026/00186 Page 13 of 21 Figure 5 Uplock Shaft N ut and Bolt Right-Hand Uplock Assem bly Bracket Air Cylinder Clevis Bracket Clam ping Bolt Left-Hand Uplock Assem bly Bracket Uplock Bracket Clevis 20 ...

  • Milnor KURSPK0026 - page 23

    HURSPK0026/00186 Page 14 of 21 Figure 6 Left-Hand Side Lock Shaft Bearing Right-Hand Side Lock Shaft Bearing Lock Shaft Spacers 21 ...

  • Milnor KURSPK0026 - page 24

    HURSPK0026/00186 Page 15 of 21 Figure 7 Right-Hand Side Lock Shaft Bearin g 22 ...

  • Milnor KURSPK0026 - page 25

    HURSPK0026/00186 Page 16 of 21 Upper Cross -Member Shaft Lock Uplock Jaw Figure 8 23 ...

  • Milnor KURSPK0026 - page 26

    HURSPK0026/00186 Page 17 of 21 Figure 9 Square Holes in the Side of the Uplock Jaw ( File Paint off of the Inside surf ace of the Holes ) 24 ...

  • Milnor KURSPK0026 - page 27

    HURSPK0026/00186 Page 18 of 21 Figure 10 Old Setup of Dom e Full-Up Contact Switch and Bracket Figure 11 25 ...

  • Milnor KURSPK0026 - page 28

    HURSPK0026/00186 Page 19 of 21 New Positioning of Dom e Full-Up Contact Switch and Bracket Dom e Full-Up Contact Switch Bracket Dom e Full-Up Contact Switch Figure 12 26 ...

  • Milnor KURSPK0026 - page 29

    HURSPK0026/00186 Page 20 of 21 Figure 13 27 ...

  • Milnor KURSPK0026 - page 30

    HURSPK0026/00186 Page 21 of 21 Figure 14 Lock Ring Bolts Location of Downlock Shim s 28 ...

Produzent Milnor Kategorie Clothes Dryer

Dokumente, die wir vom Produzenten des Geräts Milnor KURSPK0026 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Milnor
- Bedienungsanleitungen KURSPK0026
- Produktkarten Milnor
- Informationsbroschüren
- oder Energieetiketten Milnor KURSPK0026
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Milnor KURSPK0026.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Milnor KURSPK0026, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Milnor KURSPK0026. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Milnor KURSPK0026 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Milnor KURSPK0026, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Milnor KURSPK0026 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Milnor KURSPK0026 verständlich ist.

Eine gänzliche Bedienungsanleitung von Milnor sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Milnor KURSPK0026 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Milnor KURSPK0026 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Milnor KURSPK0026, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Milnor KURSPK0026 - die uns die ersten Schritte während der Nutzung von Milnor KURSPK0026 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Milnor KURSPK0026 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Milnor KURSPK0026 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Milnor KURSPK0026?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Milnor KURSPK0026 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Milnor KURSPK0026 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)