Bedienungsanleitung MaxTech NX-16

14 Seiten 0.04 mb
Download

Zur Seite of 14

Summary
  • MaxTech NX-16 - page 1

    User's Guide NX-16 Series High Performance Software Configurable 16-bit ISA NE-2000 compatible Ethernet Adapters Part #MAN005 Rev. 1.1 ...

  • MaxTech NX-16 - page 2

    Please take a moment to note the following infor- mation. Include this form in the unlikly event that you need to return the product for warranty service. Refer to Section Eight for complete Warranty information and procedures on returning your product. Product: _________________________ Serial Number: ____________________ Purchase Date: __________ ...

  • MaxTech NX-16 - page 3

    1 Contents Section One - Introduction ......................... 1 Section Two - Installation ........................... 2 Section Three - Driver Installation .............. 7 Section Four - Troubleshooting .................. 7 Section Five - Cable Information .............. 9 Section Six - Specifications ..................... 10 Section Seven - Te ...

  • MaxTech NX-16 - page 4

    2 Minimum hardware requirements are an IBM PC/XT (or better) fully compatible PC with 512K RAM running DOS 3.3 or higher. The network operating system you use may have higher requirements. Section Two - Installation This section will provide step by step in- structions on how to install your new Maxtech network adapter. Installation of this network ...

  • MaxTech NX-16 - page 5

    3 2.2 Hardware Installation Installation of this adapter card requires opening and manipulating your PC. Exercise cau- tion at all times when working with AC powered and static-sensitive equipment. Turn off and un- plug your PC before installation. Discharge any static electricity from your body by touching any metal surface. 1. Turn off your compu ...

  • MaxTech NX-16 - page 6

    4 6. Carefully install the adapter by firmly press- ing the card into the slot you have chosen, applying even pressure until the adapter is completely seated in the slot. 7. Fasten the retaining bracket with the screw from the slot cover. Make sure the adapter is properly aligned. Store the slot cover for future use. 8. Replace the computer cover a ...

  • MaxTech NX-16 - page 7

    5 Running the SETUP program 1. Insert the installation diskette into your drive, log on to that drive, and run the SETUP program in the DIAG subdirectory. Assuming that your have inserted the dis- kette in drive A, you would type the follow- ing at the DOS C: drive prompt: A: [ENTER] DIAGSETUP [ENTER] 2. Select the network adapter that you would ...

  • MaxTech NX-16 - page 8

    6 2.4 Testing The Adapter The SETUP program provides an option in its main menu for adapter diagnostics. One or more PCs on the network can run the test simulta- neously. The Test Adapter option runs several tests and the results are indicated by either PASS or FAIL. Make sure that the network cable is attached (and properly terminated if using a B ...

  • MaxTech NX-16 - page 9

    7 sure that the notch on the ROM matches that on the socket (refer to Figure 2). 2. Configure the adapter using the SETUP program to enable the Boot ROM function by selecting the appropriate address from the Boot ROM Base Address option. Refer to Section 2.3 for more information on running the SETUP program. 3. Follow the Remote Boot Workstation in ...

  • MaxTech NX-16 - page 10

    8 README.TXT file describing the driver. Refer to the RELEASE.TXT file on the installation diskette for more information on the available drivers. Section Four - Troubleshooting This section describes some of the com- mon problems you may encounter while using your network adapter. When troubleshooting, you should make sure that the network you are ...

  • MaxTech NX-16 - page 11

    9 4.2 Cable Problems A) Observe the green Link Status LED if you are using a 10Base-T network. Turn on the computer. Connect the network cable and observe the green LINK LED. If the LED is ON, then the system is connected. Otherwise check for a proper RJ-45 connection. B) Make sure the coaxial cable is prop- erly terminated if you are using a 10Bas ...

  • MaxTech NX-16 - page 12

    10 must use solid copper conductors and UL codes CM, CMR, and CMP are required. The computer on the network is connected via a star topology (i.e. each node is connected to a HUB, not to each other). Maximum cable length is 300' (100 m). 10Base-2 networks uses a single conduc- tor coaxial cable and BNC connectors. Use only RG-58A/U or RG-58C/U ...

  • MaxTech NX-16 - page 13

    11 Section Seven - Technical Support In the unlikely event you experience difficulty in the use of the product, or if it does not operate as described, we suggest you: (1) consult the Troubleshooting section of this guide and (2) consult with your dealer. If you have not referred to the Troubleshooting section, there is a good chance the solution t ...

  • MaxTech NX-16 - page 14

    12 (also enclose a check for out-of-warranty repair). En- close your check or Postal Money Order for $7.50 to cover the cost of return shipping/handling. Please do not send cash or stamps. 4. After wrapping the package securely for shipping, print your name, return address and the RMA # clearly on the outside of your package. 5. Ship the unit prepa ...

Produzent MaxTech Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts MaxTech NX-16 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen MaxTech
- Bedienungsanleitungen NX-16
- Produktkarten MaxTech
- Informationsbroschüren
- oder Energieetiketten MaxTech NX-16
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung MaxTech NX-16.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen MaxTech NX-16, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen MaxTech NX-16. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts MaxTech NX-16 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts MaxTech NX-16, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von MaxTech NX-16 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von MaxTech NX-16 verständlich ist.

Eine gänzliche Bedienungsanleitung von MaxTech sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von MaxTech NX-16 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von MaxTech NX-16 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich MaxTech NX-16, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts MaxTech NX-16 - die uns die ersten Schritte während der Nutzung von MaxTech NX-16 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit MaxTech NX-16 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von MaxTech NX-16 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich MaxTech NX-16?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit MaxTech NX-16 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit MaxTech NX-16 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)