Bedienungsanleitung Honeywell CT87A

12 Seiten 0.29 mb
Download

Zur Seite of 12

Summary
  • Honeywell CT87A - page 1

    ® U.S. Registered Trademark Copyright © 2002 Honeywell All Rights Reserved 69-0274-6 Verify that you have the correct thermostat Using the compatibility chart below , verify that you purchased the correct CT87 Thermostat for your heating/cooling system. If you are unsure which model is right for your system, visit www .honeywell.com/ yourhome or ...

  • Honeywell CT87A - page 2

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 2 Prepare for installation 1. Carefully unpack your new thermostat; rough handling may affect it s accuracy . Save your receipt and identify the following parts: • CT87 Thermostat • Screws: two 1-in. sheet metal screws, two 1/2-in. binding head screws, and two 1/4-in. round head screws • W allplate (CT8 ...

  • Honeywell CT87A - page 3

    CT87A,B,J ROUND® THERMOSTAT 3 69-0274-6 5. Label the wires using the wiring labels that came with the CT87. Identify each wire using the letter of the terminal on th e old the rmo- stat (Fig. 2). Do not label the wires by color . 6. Disconnect the wires from the o ld thermostat and wrap them around a pencil to keep them from falling back into the ...

  • Honeywell CT87A - page 4

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 4 1. If using the cover ring: Position the cover ring again st the wall so that the arrow in the middle of th e cover ring is pointing up. 2. Position the wallp late or subbase . • If using cover ring : Place the wallplate/subbase over the cover ring. Rotate the wallpl ate/subbase until the wiring o penings ...

  • Honeywell CT87A - page 5

    CT87A,B,J ROUND® THERMOSTAT 5 69-0274-6 1. Place the cover ring against the outlet box so that the arrow in the middle of the cover ring is pointing up. 2. Pull the wires through the wiring hole on the bottom left side of the cover ring. 3. Align the screw slots on the cover ring with the outlet box screw holes, and attach the cover ring to the ou ...

  • Honeywell CT87A - page 6

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 6 Wire the thermostat 1. Use the wiring cross-reference table below to match each old thermostat wire with its corresponding terminal on the CT87 wallpl ate or subbase. See Fig. 8 through 13 wiring diagrams. *Never attach wires to both the B and O terminals. 2. S trip the wire insulation as needed to fit the w ...

  • Honeywell CT87A - page 7

    CT87A,B,J ROUND® THERMOSTAT 7 69-0274-6 Fig. 8. CT87A for a 2-wire heat ing only system. Fig. 9. CT87A for a 3-wire hot water heating only system . Fig. 10. CT87B for a 4-wire heat ing/cooling system . M2018 3 CT87A WALLPLATE TO SYSTEM R W Y POWER HEAT M2018 4 WIRE LABELS (LETTERS ON ORIGINAL THERMOSTAT TERMINALS) CT87A WALLPLATE 3-WIRE HOT WATER ...

  • Honeywell CT87A - page 8

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 8 Fig. 1 1. CT87B for a 5-wire heating /cooling system. Fig. 12. CT87J for a 4-wire single stage heat pump. Fig. 13. CT87J for 4-wire single stage heat pump. C O O L • O F F • H E A T F A N O N • A U T O M2022 5 HEATING POWER CT87B SUBBASE TO SYSTE M TO SYSTEM R H G R C W Y FAN HEAT COOLING POWER COOL C ...

  • Honeywell CT87A - page 9

    CT87A,B,J ROUND® THERMOSTAT 9 69-0274-6 Mount the thermostat 1. Pull off the thermostat cover and discard the red plastic insert that holds the mercury switch in place during shipping. 2. Using a pencil po int, slide the heat anticipator indicato r to 1.2 on the scale as shown in Fig. 14. IMPORT ANT : This prevents the thermostat from being damage ...

  • Honeywell CT87A - page 10

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 10 Set the heat anticipator for your system IMPORT ANT : Setting th e heat anticipator allows the thermostat to maintain accurate temperature control. 1. Using a pencil point, move the heat anticipator pointer to the numbe r that you recorded in S tep 3, su b- step 3. If you could not find the anticipator sett ...

  • Honeywell CT87A - page 11

    CT87A,B,J ROUND® THERMOSTAT 1 1 69-0274 -6 Check cooling IMPORT ANT : T o a void damaging the compressor in the air conditioner , do not operate the cooling system when the outdoor temp erature is below 50°F (10°C). 1. If your CT87 has a subbase, set the System switch on the left to Cool. IMPORT ANT : Af ter heating is teste d, wait five minutes ...

  • Honeywell CT87A - page 12

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 G .H. Rev . 08-02 www .honeywell.com/yourhome Automation and Control Solutions Honeywell Honeywell Limi ted-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. H ...

Produzent Honeywell Kategorie Thermostat

Dokumente, die wir vom Produzenten des Geräts Honeywell CT87A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen CT87A
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell CT87A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell CT87A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell CT87A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell CT87A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell CT87A ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell CT87A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell CT87A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell CT87A verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell CT87A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell CT87A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell CT87A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell CT87A - die uns die ersten Schritte während der Nutzung von Honeywell CT87A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell CT87A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell CT87A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell CT87A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell CT87A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell CT87A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)