-
Pelco C1603M - page 1
DX8000-ISCI SCSI Installation Manual C1603M (6/04) Digital Video Recorder DX8000 ...
-
Pelco C1603M - page 2
Protecting people and property in a million locations worldwide. ...
-
Pelco C1603M - page 3
C1603M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-ISCI internal SCSI adapter . PARTS LIST Qty Description 1 Adaptec ® 29160N UltraWide SCSI adapter 1 Floppy diskette* 1 Adaptec installation instruction booklet* 1 Adhesive-backed upgrade part label 1 Pelco installation instruction booklet *T ...
-
Pelco C1603M - page 4
2 C1603M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed section. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shuttin ...
-
Pelco C1603M - page 5
C1603M (6/04) 3 Figure 3. Removing Power Cord from Unit ...
-
Pelco C1603M - page 6
4 C1603M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective m ...
-
Pelco C1603M - page 7
C1603M (6/04) 5 Prepare the Unit OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the unit chassis: a. Dis ...
-
Pelco C1603M - page 8
6 C1603M (6/04) c. Carefully remove the chassis cover by sliding it back and up. Set aside the cover . Figure 5 illustrates the interior of the DX8000. Figure 5. Removing Chassis Cover ...
-
Pelco C1603M - page 9
C1603M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . Figure 6. DX8000 Interior POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRA ...
-
Pelco C1603M - page 10
8 C1603M (6/04) REMOVE THE REAR CROSS-BRACE 1. Using a Phillips-head screwdriver , remove the two flat-head screws that secure the rear cross-brace. Then liftout the cross-brace. Refer to Figure 7. Figure 7. Removing Rear Cross-Brace ...
-
Pelco C1603M - page 11
C1603M (6/04) 9 2. Move the rear cross-brace aside and keep the screws for later use. Figure 8. Moving Rear Cross-Brace to Back of Unit ...
-
Pelco C1603M - page 12
10 C1603M (6/04) Install the DX8000-ISCI SCSI Card 1. Locate PCI Slot 1 on the system motherboard. This is the expansion slot that is closest to the system’ s VGA card. Refer to Figure 9. Figure 9. Location of PCI Slot 1 ...
-
Pelco C1603M - page 13
C1603M (6/04) 11 2. Remove the slot cover from PCI Slot 1: a. Using a Phillips-head screwdriver , remove the screw that fastens the slot cover to the chassis. Retain this screw for use in step 4d. b. Remove the slot cover from PCI Slot 1. Figure 10. Removing the Slot Cover for PCI Slot 1 ...
-
Pelco C1603M - page 14
12 C1603M (6/04) 3. Carefully remove the DX8000-ISCI SCSI card from its static-safe packaging. Handle the adapter card by its edges and slot cover , and avoid touching the card’ s components, connectors, and conductive leads. 4. Insert the DX8000-ISCI SCSI card in PCI Slot 1: a. Carefully move aside any cables blocking access to PCI Slot 1. b. In ...
-
Pelco C1603M - page 15
C1603M (6/04) 13 d. Using the screw you removed in step 2a, secure the DX8000-ISCI card to the chassis. Refer to Figure 12. Figure 12. Securing the DX8000-ISCI SCSI Card 4d ...
-
Pelco C1603M - page 16
14 C1603M (6/04) Reassemble the Unit 1. Replace the rear cross-brace, and secure it with the flat-head screws you set aside earlier . Refer to Figure 13. Figure 13. Replacing Front Cross-Brace ...
-
Pelco C1603M - page 17
C1603M (6/04) 15 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 14. Figure 14. Replacing Chassis Cover 3. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the l ...
-
Pelco C1603M - page 18
16 C1603M (6/04) c. Press down firmly to ensure that the label properly adheres to the inside of the door . NOTE: In the event that your unit or its components require service, part labels must be present and appropriately affixed to the unit’ s door . Pelco product support personnel use these labels to identify the exact components installed in ...
-
Pelco C1603M - page 19
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models ...
-
Pelco C1603M - page 20
Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation. Adaptec is a registered trademark of Adaptec Incorporated. C1603M (6/04) W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: ...
Do you have a question concerning Pelco C1603M?
Use the form below
If you did not solve your problem by using a manual Pelco C1603M, ask a question using the form below. If a user had a similar problem with Pelco C1603M it is likely that he will want to share the way to solve it.