-
Grizzly G0594 - page 1
MO DE L G0 594 Lar ge Ch i pper / Sh redde r O WNER'S MANU A L COPYRIGHT © NOVEMBER, 20 05 BY GRIZ ZL Y I NDUSTRIAL , INC. W AR NI NG : N O P ORT IO N OF TH IS MA NUAL MA Y BE RE PRODU CED I N A NY SH APE OR FORM WI TH OUT T HE WR IT T EN APPROV AL OF GR IZ ZL Y I NDU STR IA L , I NC. #E W765 6 PRINTED IN CHINA ...
-
Grizzly G0594 - page 2
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. ...
-
Grizzly G0594 - page 3
T able of Cont en ts INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Machine Data Sheet ....................... ...
-
Grizzly G0594 - page 4
-2 - G0 594 Large Chipper/ Shredder Customer Ser vice #: (570) 5 46 -9 663 • T o Order Call: (80 0) 523 -4 77 7 • F ax #: (8 00 ) 438 -59 0 1 MA CHINE D A T A SHEE T MOD EL G059 4 L ARGE CHI PPER / SHRED DE R If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documen ...
-
Grizzly G0594 - page 5
G0594 L arge Chip per/Shredder -3 - Figure 1. Chipper/shredder identification. Machine Identification ( Figures 1 & 2 ) A. Hopper B. Motor C. Chip Outlet D. Chipper Funnel E. Choke F. Gas Cap G. Throttle H. ON/OFF Switch I. Pull Start Handle J. Gas Shut Off Valve K. Exhaust Identi fi cat ion A K Figure 2. Motor identification. D E F I J B C H G ...
-
Grizzly G0594 - page 6
- 4- G0 594 Large Chipper/ Shredder 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO N OT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con - tain long hair and wear non-slip foot ...
-
Grizzly G0594 - page 7
G0594 L arge Chip per/Shredder -5 - 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, an ...
-
Grizzly G0594 - page 8
- 6 - G0594 Large Chip per/Shredder A ddit ion al S af et y In str ucti on s f or Ch ipper / Sh redders 5. C LO TH ING : DO NOT wear loose clothing, neckties, scarves, or jewelry which may get caught in moving parts. DO NOT wear clothing or gloves with pull ties or straps. This type of clothing could get tangled with material that is being shredded ...
-
Grizzly G0594 - page 9
G0594 L arge Chip per/Shredder - 7 - No list of safet y guideline s can be complete. E ver y environment is diffe rent . Alway s con - sider safet y first , as it ap plies to your indi - vidual working conditions . Us e t his an d other machiner y with caution and r espec t. Fail ure to do so could r esult in serious pe r - sonal injur y , d amage ...
-
Grizzly G0594 - page 10
-8- G0594 L arge Chip per/Shredder The Model G0 594 was carefully packed when it left our warehouse . If you d iscov er the machine is damaged af ter you hav e signed for delive r y , please i mmedi ately c all Customer Service at ( 5 70) 546 -9 66 3 for advice. Sav e the containers and all pack ing mate rials for possible inspec tion by t he carri ...
-
Grizzly G0594 - page 11
G0594 L arge Chip per/Shredder -9 - In ve nt or y After all the par ts have been remov ed from the box, you should have the following items: Inv entor y ( Figure 3 ) Qt y A . Chipper/ Shredder ....................................... 1 B. Wheel Assembly ......................................... 2 C. Hopper ........................................... ...
-
Grizzly G0594 - page 12
- 1 0 - G0 594 Large Chipper/S hredder Figure 5. Positioning the hopper gasket. 4. Place the ho pper on top of the gasket and line up all of t he holes. Place rubber grom - mets and fender washers on t wo hex bolts, thread them through the holes nearest t he motor and sec ure them wit h flat washers, lock washers, and lock nuts . 5. Line up the hol ...
-
Grizzly G0594 - page 13
G0594 L arge Chip per/Shredder - 1 1 - Damag e t o y our ey es, hands, and ears could result from usin g this machine without prop - er protec tive g ear . Alw ays wea r safet y glass - es, hearing pr otection, and l eather glo ves when op erating this machine. Lo o se ha i r a nd c l ot h - ing could g et c aught in machiner y a nd cause seri - ou ...
-
Grizzly G0594 - page 14
- 1 2- G0594 Large Chipper/ Shredder To shred twigs, leaves, and brush: 1. Slowly pour the material into the hopper. DO NOT try to stuff too much material in at one time or the machine will jam. 2. Use a 1" diameter branch to push the mate- rial into the hopper if necessary (see Figure 9 ). DO NOT use your hands! Figure 9. Shredding leaves. 4. ...
-
Grizzly G0594 - page 15
G0594 L arge Chip per/Shredder - 1 3 - T urn OFF the machine, allow all moving par ts to come to a complete stop, and dis - connect the spark plug wire b efore moving the machine, empt ying the b ag, unclogging the inlets or outlets , filli ng the gas tank , or per forming maintenance and rep airs . Before and af ter u sing the c hipper /shred der ...
-
Grizzly G0594 - page 16
- 1 4 - G0594 L arge Chi pper/Shredd er Revie w the troubleshooting and procedures in this section to fix y our machine if a problem de velops. If y ou need replacement parts or you are unsure of your repair skills, t hen feel free to call our T echnical Supp ort at ( 5 70) 546 - 966 3 for machine repairs, or c ontact Briggs & Strat ton for mot ...
-
Grizzly G0594 - page 17
G0594 L arge Chip per/Shredder - 1 5 - Repl aci ng V - Belt Figure 1 2 . Replacing V - belt. 3. Loosen the idler pulley and roll the belt off of the pulleys (see Figure 12 ). 4. Install the new belt and adjust the idler pulley so the V-belt deflects approximately 3 ⁄ 8 " when pushed with moderate pressure. 5. Replace the V-belt cover and re- ...
-
Grizzly G0594 - page 18
- 1 6 - G0594 L arge Chi pper/Shredd er ? ...
-
Grizzly G0594 - page 19
G0594 L arge Chip per/Shredder - 1 7 - P ar ts L is t Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (8 ...
-
Grizzly G0594 - page 20
- 1 8 - G0594 Large Chipper/ Shredder Grizzly Industrial, Inc. warran ts eve r y produc t it sells for a perio d of 1 year to t he ori ginal purchaser from the date of purchase. This warranty does not ap ply to d ef ec ts due directly or indirec tly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz ...
-
Grizzly G0594 - page 21
...
-
Grizzly G0594 - page 22
? ...
-
Grizzly G0594 - page 23
...
-
Grizzly G0594 - page 24
...
Do you have a question concerning Grizzly G0594?
Use the form below
If you did not solve your problem by using a manual Grizzly G0594, ask a question using the form below. If a user had a similar problem with Grizzly G0594 it is likely that he will want to share the way to solve it.