Bedienungsanleitung Telex BP-2002

8 Seiten 0.13 mb
Download

Zur Seite of 8

Summary
  • Telex BP-2002 - page 1

    BP-1002/BP-2002 Beltpac ks A udiocom ® Inter com System 93507740000 Rev J 5/2006 Operating Instructions ...

  • Telex BP-2002 - page 2

    FCC ST A TEMENT This equipment uses, and can radiate radio frequency energy that ma y cause interference to r adio communications if not installed in accordance with this manual. The equipment has been tested and found to comply with the limits of a Class A computing device pursuant to Subpar t B, P ar t 15 of FCC Rules which are designed to provid ...

  • Telex BP-2002 - page 3

    3 INTRODUCTION The A udiocom ®1 BP-1002 and BP-2002 are microprocessor controlled one- and two-channel intercom beltpac ks. An internal switch and jumper setting allows the units to be used with Clear-Com ®2 components , if desired. Other inter nal switch and jumper settings allow the unit to be uniquely configured to the operator’ s requiremen ...

  • Telex BP-2002 - page 4

    13 4 Figure 1. BP-2002 & BP-1002 Connections and Controls APPENDIX A OPTIONAL FOO TBALL MODIFICA TIONS GENERAL DESCRIPTION In A udiocom ® Intercom Systems, the Mic-Kill f eature is used to tur n off any activated microphones on a selected channel. The Mic-Kill f eature is activated when the beltpack receives a 24 kHz signal from the channel. I ...

  • Telex BP-2002 - page 5

    12 5 EXTERNAL CONNECTIONS & CONTROLS NO TE: The numbers refer to the callouts in Figure 1. 1. V OLUME C ONTROL : Use this control to adjust the headset listen lev el. 2. C HAN B UTTON AND I NDICA T ORS : The Chan button (only on the BP-2002) allows the user to select which intercom channel is active . Press the Chan button to change the channel ...

  • Telex BP-2002 - page 6

    11 6 7. I NTERCOM C HANNEL C ONNECTORS : On the BP-2002, intercom channels are connected via a pair of 6-pin connectors (one male and one female). The male and female connectors are wired together in par allel, providing a “loop through” at each connector pin. Use one connector to connect to the intercom channel. Use the other connector to “d ...

  • Telex BP-2002 - page 7

    10 7 Changing Modes of Operation: P erform the following steps to change the mode of operation. 1 . Both the T alk and Call indicators should be off and the headset should be connected 2 . Press and hold the T alk key , then press and hold the Call key , then release both ke ys. The Call indicator should now glow red. (The number of beeps heard in ...

  • Telex BP-2002 - page 8

    9 8 INTERNAL SWITCHES, JUMPERS AND ADJUSTMENTS There are sev eral internal switches, jumpers and adjustments that aff ect operation. These are described below . T o gain access to the s witches, jumpers and adjustments, disconnect all power and line connections. Remov e two screws from the top of each side and two scre ws from bottom of each side. ...

Produzent Telex Kategorie Intercom System

Dokumente, die wir vom Produzenten des Geräts Telex BP-2002 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Telex
- Bedienungsanleitungen BP-2002
- Produktkarten Telex
- Informationsbroschüren
- oder Energieetiketten Telex BP-2002
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Telex BP-2002.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Telex BP-2002, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Telex BP-2002. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Telex BP-2002 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Telex BP-2002, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Telex BP-2002 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Telex BP-2002 verständlich ist.

Eine gänzliche Bedienungsanleitung von Telex sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Telex BP-2002 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Telex BP-2002 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Telex BP-2002, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Telex BP-2002 - die uns die ersten Schritte während der Nutzung von Telex BP-2002 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Telex BP-2002 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Telex BP-2002 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Telex BP-2002?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Telex BP-2002 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Telex BP-2002 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)