-
Graco 258880 - page 1
3A0705E Operation Tr u e C o a t ™ Pr o and T rueCoat ™ Plus Cor dless P aint Spra yer s - For portable spray applicati ons of water -based and oil-based (mineral spirit-type ) architectural paint s and coatings onl y - - Not f or use in e xplosive atmospheres - Models 258864, 258880 Maximum W orking Pressure 2000 psi (137 bar , 13.7 MP a) IMPO ...
-
Graco 258880 - page 2
Table of Contents 2 3A0705E T able of Contents W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Ident ification . . . . . . . . . . . . . . . . . . . . . . . . . 5 Common Pr ocedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pressure Relief Procedure . . . . . . . . . . . . . . . . . ...
-
Graco 258880 - page 3
Warnings 3A0705E 3 Wa r n i n g s The follo wi ng warnings are for the setup, use, ma intenance, and repair of this equipment. Th e e xclamatio n point symbol aler ts y ou to a general warning and the ha zard symbols refer to procedure-sp ecific risks. When these symbols appear in the body of thi s manual, ref er back to these W ar nings. Product-s ...
-
Graco 258880 - page 4
Warnings 4 3A0705E B A TTER Y HAZARD The batter y may leak, e xplode, cause b ur ns, or cause an explosion if mishandled. Contents of an open battery can cause se vere irritation and/or chemical burns. If on skin, wash with soap and w ater . If in ey es, flush with water f or at least 15 minutes and seek immediate medical attention. • Do not shor ...
-
Graco 258880 - page 5
Component Identification 3A0705E 5 Component Identification *NO TE: Filter asse mbly is re verse-threade d. T ur n left (or co unter-clockwise) to tighte n, tur n rig ht (or clockwise) to loos en. ti15479a F E R K M X T S W B D P A G J H N C C A Cordless Paint Spra yer B Spra yer Hook C Spra y Tip/Guard Assembly (311, 515 include d) D Tip Filter (* ...
-
Graco 258880 - page 6
Common Procedures 6 3A0705E Common Pr ocedures Pressure Relief Pr ocedure 1. Engage tr igger lock. 2. Put prime/relief v alve UP to re lease pressure. Tr i g g e r L o c k Spra y Tip P osition Prime/Relief V alve P osition Do not opera te or spra y near children. Do not aim the spra yer at , or spra y any person or animal. K eep hands and other bod ...
-
Graco 258880 - page 7
Charging the Battery 3A0705E 7 Char ging the Batter y Batteries are initially 50% charge s to provide optimum battery life and requir e charging before first use. It takes approximatel y 45 minutes to charge a dead battery to 80%, at which point it can be used.It will take approxi- mately 75 minutes to fully char ge a dead battery. 1. Slide batter ...
-
Graco 258880 - page 8
Setup 8 3A0705E Setup Installing Suction T ube Aim the inlet of the suction tube at the front of the material cup (towards Spray Tip/Guard Assemb ly) dur ing installa- tion. Spra ying Stains or Clear Coats (Fine-Finish Optimizer) The Fine-Finish Optimiz er shou ld be installe d and used when spra ying thin material such as stain or clear coats . Th ...
-
Graco 258880 - page 9
Setup 3A0705E 9 Spra yer Setup This spra yer arrives from the f actor y with a small amount of test ma teria l in the system. It is im por tant that you flush thi s material from the spra yer bef ore using it f or the first ti me: 1. Fill material cup with wate r and thread onto spray er . 2. Put prime/relief valv e to UP position, then hold tr ig- ...
-
Graco 258880 - page 10
Setup 10 3A0705E Materials • Whe n spra ying water-b ased mate rials, flush the spra yer thoroughly with w ater . • Whe n spra ying non-water- based mater ial s, flush the spra yer thoroughly with mineral spirits or com- patib le, oil-based flushing fl uid. Star ting a New Job (o r Refilling the Cup) 1. Engage trigger lock and put prime/relief ...
-
Graco 258880 - page 11
Install Tip/ Guard Assembly (if not installed) 3A0705E 11 Install Tip/Guar d Assembl y (if not installed) Rever sible Tip Selection Chart 1. Engage trigger lock and put prime/relief valv e UP to release pressure . Then remove Tip/Guard Assemb ly . 2. Install filter to Spra y Tip/Guard Assembly (make sure filter is fully installed into spra yer). NO ...
-
Graco 258880 - page 12
Basic Spraying Techniques 12 3A0705E Basic Spra ying T echniques NO TE: Use a piece of scrap cardboa rd to practice these basic spra ying techniques bef ore you begin spr aying t he surf ace. Anything y ou don’t want painted that is in the area of your spraying surface shou ld be covered or remo ved. Hold spra yer at least 2 5 cm (10 in.) from su ...
-
Graco 258880 - page 13
Unclogging Spray Tip/Guard Assembly 3A0705E 13 Unc logging Spra y Tip/Guar d Assembl y Occasionally , debris from material can accumulate and clog the spra y tip. P erf or m the fo llowing steps to unclog the tip . 1. T o unclog tip obstr uction, eng age trig ger lock and pull relief valv e UP to release pressure. 2. Re verse spra y tip to UNCLOG p ...
-
Graco 258880 - page 14
Shutdown and Cleaning 14 3A0705E Shutdo wn and Cleaning Flushing Spra yer 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remo ve material cup and pr oper ly dispose cup liner or e xcess material. 3. Remo ve and clean spr ay er intake tube and screen with wat er (or flushing fluid) and a brush e very time you flush the spr ...
-
Graco 258880 - page 15
Shutdown and Cleaning 3A0705E 15 6. Disconnect trigger loc k and trigger spra yer f or appro ximately 15 seco nds. Engage trigger loc k. 7. Discard contaminated fluid and refill with appropr i- ate flushing fluid. 8. Disengage trigger loc k, re verse tip to UNCLOG position, an d pull tr igger for 5 seconds to pr ime spra yer . 9. Put prime/relief v ...
-
Graco 258880 - page 16
Storage 16 3A0705E Cleaning Spra yer Exterior • Wipe paint off outside of spray er using a soft cloth moistened with w ater or flushing fluid. Do NO T submerge the spra yer . Tips • Tips will require replac ement depending on abrasiveness of paint. • Do no t spray with w or n tip . See T roub leshooting , page 18. Storage 1. Dilute 4 oz. bott ...
-
Graco 258880 - page 17
Replacement Parts and Kits 3A0705E 17 Replacement P ar ts and Kits 1 8 11 7 5 4 20 6 12 15 ti15497a 2 13 14 9 16 17 19 18 3 21 22 10 10a 10 10a Ref. Part Description 1 262368 Spra yer , replacement (no tip /guard, batter y , suction tube, or material cup) (Model 258864) 2 16D562 Liner, replacement (10 pack ) 3 24F045 Fine Finish Optimizer (with Cle ...
-
Graco 258880 - page 18
Troubleshooti ng 18 3A0705E T roub leshooting Chec k ev er ything in this T roubleshootin g T able bef ore you br ing the spra yer t o an authorized ser vice center . Prob lem Cause Solution Spra yer makes no sound when trigge r is pulled T rigge r is lock ed. Disengage tr igger lock. See page 6. Status Indicator Light is solid RED when tr ig- geri ...
-
Graco 258880 - page 19
Troubleshooting 3A0705E 19 Spra y Pattern Dia gnostics P oor spray results Tip is par ti ally clogged See Unclog ging Tip/Guard Assemb ly , page 13. Tip is not in co rrect position Rotate tip to SPRA Y position. Incorrect tip f or application of material. See Reversib le Tip Selection Char t, page 11. Tip filter is par tia lly clogged Clean or repl ...
-
Graco 258880 - page 20
Troubleshooti ng 20 3A0705E Spra y patter n is too nar row: Spra yer is too close to target surf ace. Incorrect tip for appli cation of mater ial. Tip is worn or damaged . Mov e spray er awa y from surface (10 in). See Reversible Tip Selection Chart, page 11. Replace tip. See Install Ti p/Guard Assembl y , page 11. Spra y pattern is too wide: Spray ...
-
Graco 258880 - page 21
Alternate Priming Method 3A0705E 21 Alternate Priming Method 1. Engage tr igger lock and put p rime/ relief valv e U P to release pressure . 2. Remov e material cup and f ill with flushing mater ial. 3. With spray er in pr ime mode, tur n spray er upside-do wn, remov e strainer , and slowly pour flushing mater ial in to the intake tube until fu ll. ...
-
Graco 258880 - page 22
Inlet Valve Cleaning 22 3A0705E Inlet V alve Cleaning Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove material cup and suctio n tube. 3. Hold spr ay er upside-down and use wrench or sock et to loo sen and remove inlet fitting, inlet valv e, and spring. NO TE: Make sure the spring also comes out . Use need ...
-
Graco 258880 - page 23
Technical Data 3A0705E 23 Te c h n i c a l D a t a Sprayer: Maximum working pressure 137.8 bar , 13.7 MP a (2000 psi) W eight 2.87 kg (6.32 lb) Dimensions: Length 33.6 cm (13.25 in.) Width 12.7 cm (5.0 in.) Height 26.4 cm (10.375 in.) Storage temperature r ange ◆❖ 0° to 50° C (32° to 122° F) Operating temperature r ange ✔ 4° to 32° C (4 ...
-
Graco 258880 - page 24
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original instructions. This m anual contains English. MM 3A0705 Graco Headquarters: Minneapolis ...
Haben Sie eine Frage bezüglich Graco 258880?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Graco 258880 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Graco 258880 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.