-
Omnitron Systems Technology 2FXM2 - page 1
iConverter ® 2FXM2 Media Converter and Network Interface Device ST ANDALONE AND PLUG-IN MODULE USER MANUAL Release 3.4 ...
-
Omnitron Systems Technology 2FXM2 - page 2
Page 2 T able of Contents 1.0 Overview .................................................................................................................... 3 1.1 General Description .................................................................................................... 3 1.1.1 Advanced Features ......................................... ...
-
Omnitron Systems Technology 2FXM2 - page 3
1.0 OVERVIEW This document describes the installation and configuration of the iConverter 2FXM2 standalone Network Interface Device and plug-in modules. The dif ference between the module types are indicated using the following legend throughout this User Manual: - Plug-In PI - S t andalone SA 1.1 GENERAL DESCRIPTION The Omnitron iConverter ® 2FXM ...
-
Omnitron Systems Technology 2FXM2 - page 4
2.0 PORT STRUCTURE 2.1 OVERVIEW The front panel of the 2FXM2 provides access to the management (serial console) and fiber ports. T h e SFP fiber ports support 100BASE-FX transceivers. The plug-in module features two additional Ethernet ports for connectivity via the chassis backplane. 2.1.1 Management Port PI SA The 2FXM2 features a Serial RS-232 C ...
-
Omnitron Systems Technology 2FXM2 - page 5
AA A AA AA AA A AA A AA AA AA BB BBB BBB BB B BBB BBB BB 1 2 3 4 5 6789 1 0 11 1 2 13 14 15 16 17 18 19 “A” Data bus “B” Data bus 19-Module Chassis A B 12 3 4 5 AB AB A B A B 12 4 5 3 “A” Data bus “B” Data bus AB Managed Power Chassis by Omnitron Systems Technology, Inc. iConverter ™ “A” Data bus AB 5-Module Chassis 2-Module C ...
-
Omnitron Systems Technology 2FXM2 - page 6
Switch 1 Switch 8 Left Switch 1 Switch 8 Bank 2 Bank 1 Right DIP-switch Locations 3.2.1 Board-Mounted Bank 1 Settings PI SA DIP-switch Bank 1 is available on both the plug-in and standalone modules. The table indicates the position of the switch; Left/Down or Right/Up. As indicated in the DIP-switch location diagram, Left and Right refers to the pl ...
-
Omnitron Systems Technology 2FXM2 - page 7
NOTE: DIP-switches marked Reserved must be kept in the Left (factory default) position. 3.2.1.5 SW5 - Fiber Port 2 Full/Half Duplex “FDX/HDX” When the DIP-switch is in the Full Duplex “FDX” position (factory default), the fiber port facilitates a connection that supports Full-Duplex operation. Setting this DIP-switch to Half-Duplex “HDX? ...
-
Omnitron Systems Technology 2FXM2 - page 8
3.2.2 Board-Mounted Bank 2 Settings PI DIP-switch Bank 2 is only available on the plug-in module. Swit ch Lef t ( Factor y Defaul t ) Right SW1 A - D S: Bac kpl an e Por t A D isab led A- E N : Port A E nabl ed SW 2 B- DS: Bac kpl an e Por t B D isab led B-E N : Port B E nabl ed SW3 Res erved R ese rved SW4 M/ SL: Mas te r/S la ve A uto-S e le ct S ...
-
Omnitron Systems Technology 2FXM2 - page 9
3.3 INST ALLING PLUG-IN MODULES AND CONNECTING CABLES PI a. Carefully slide the module into an open slot in the chassis. Align the module with the installation guides and ensure that the module is firmly seated against the backplane. Secure the module by fastening the front panel thumbscrew (push in and turn clockwise to tighten) to the chassis fro ...
-
Omnitron Systems Technology 2FXM2 - page 10
3.4 CONFIGURE THE MODULE VIA COMMAND LINE INTERF ACE PI SA T o configure, attach the 2FXM2 to a DB-9 serial (RS-232) equipped computer with terminal emulation software such as HyperT erminal. The 2FXM2 Serial Console Port (DCE) is a mini DIN-6 female connector which can be changed to a DB-9 connector with the included adapter (Part #8082-0). Attach ...
-
Omnitron Systems Technology 2FXM2 - page 11
The Management Options screen will be displayed. PI SA Management Options iConverter, Serial Agent Network Management 1: Chassis and Module Management 2: Set Module Identifier Management Module Preferences 3: IP and Control Preferences 4: SNMP Preferences 5: Abandon Preference Changes 6: Save Preference Changes 7: Restore to Factory Defaults 8: Res ...
-
Omnitron Systems Technology 2FXM2 - page 12
3.4.1 Setting IP and Control Preferences An IP address is required for the SNMP manager to address the 2FXM2. The factory default setting is 192.168.1.220. The IP address can be configured manually or automatically as a DHCP client. 3.4.1.1 Setting IP Parameters Manually T o manually configure the IP address and control parameters, select 3 from th ...
-
Omnitron Systems Technology 2FXM2 - page 13
PI SA Management Options iConverter, Serial Agent Network Management 1: Chassis and Module Management 2: Set Module Identifier Management Module Preferences 3: IP and Control Preferences 4: SNMP Preferences 5: Abandon Preference Changes 6: Save Preference Changes 7: Restore to Factory Defaults 8: Restart Management Module 9: Other Networking Featur ...
-
Omnitron Systems Technology 2FXM2 - page 14
PI SA IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 2FXM2 6: Enable/Disable TELNET Enabled 7: Enable/Disable FTP Disabled 8: Enable/Disable Soft Switch Reload Disabled 9: TELNET Password ***** 10: FTP P ...
-
Omnitron Systems Technology 2FXM2 - page 15
PI SA IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 2FXM2 6: Enable/Disable TELNET Enabled 7: Enable/Disable FTP Disabled 8: Enable/Disable Soft Switch Reload Disabled 9: TELNET Password ***** 10: FTP P ...
-
Omnitron Systems Technology 2FXM2 - page 16
PI SA SNMP Preferences Screen iConverter, Serial Agent Chassis Number = 1 SNMP Engine ID 80001CAE03000687003B19 1: sysContact Omnitron (949) 250-6510 2: sysLocation Irvine, CA USA 3: SNMP Writes Enabled SNMP v1/v2c ------------------------------------------------------------------- 4: Read Community ***** 5: Write Community ***** 6: Agent Enabled S ...
-
Omnitron Systems Technology 2FXM2 - page 17
authNoPriv provides authentication based on the HMAC-MD5 algorithm and authPriv provides DES 56-bit encryption based on the HMAC-MD5 algorithm. T o set User 1 security , select 10 at the SNMP Preferences screen, press < ENTER > and then follow the screen prompts. T o set the User 2 security , select 13 at the SNMP Preferences screen, press &l ...
-
Omnitron Systems Technology 2FXM2 - page 18
Page 18 3.4.3 Enabling/Disabling Soft-switch Reload The Soft-switch Reload function controls the configurations of the 2FXM2 and other iConverter modules managed by the 2FXM2 following a power up. When the Soft-switch Reload is disabled, the configurations of the 2FXM2 and the other managed modules (non-management modules) following a return of pow ...
-
Omnitron Systems Technology 2FXM2 - page 19
3.4.4 Access the 2FXM2 Remotely Remote access to the 2FXM2 is provided via SNMP , T elnet, FTP or an external serial modem connected to the Serial Console Port. 3.4.4.1 Accessing the 2FXM2 via NetOutlook (SNMP) The 2FXM2 module can be remotely accessed by SNMP-client software such as Omnitron’ s NetOutlook SNMP Management Software or third-party ...
-
Omnitron Systems Technology 2FXM2 - page 20
Page 20 PI SA IP and Control Preferences Screen iConverter, Serial Agent 1: Set IP 192.168.1.220 2: Set Subnet Mask 255.255.255.0 3: Set Gateway 192.168.1.1 4: Chassis Number 1 5: Chassis Name (also sysName) 2FXM2 6: Enable/Disable TELNET Enabled 7: Enable/Disable FTP Disabled 8: Enable/Disable Soft Switch Reload Disabled 9: TELNET Password ***** 1 ...
-
Omnitron Systems Technology 2FXM2 - page 21
When the upload is complete, the 2FXM2 displays the update status and then automatically restarts with the newly loaded firmware. 3.4.4.4 Up dating the 2FXM2 Firmware via FTP Using an FTP application, upload the new firmware into the FTP root directory of the 2FXM2. When the file transfer is complete, the 2FXM2 verifies the file and then automatica ...
-
Omnitron Systems Technology 2FXM2 - page 22
4.0 DET AILED MODULE CONFIGURA TION PI SA 4.1 OVERVIEW The 2FXM2 has module parameters that require configuration depending on the application. The Module configuration screen is accessible by selecting the module slot number from the Chassis V iew screen. T o access the Module configuration menu, select 1 at the Management Options screen, press &l ...
-
Omnitron Systems Technology 2FXM2 - page 23
By selecting Chassis Number 1, from the Chassis Selection screen, the Chassis V iew screen will be displayed. PI Chassis View 19 Slot iConverter, Serial Agent Chassis Number = 1 Slot Model Type | Slot Model Type 1 8000-0 NMM | 16 N/A 2 8903-1 10/100M | 17 N/A 3 8911-1 10/100M | 18 N/A 4 N / A | 1 9 N / A 5 8959N-0 2FXM2 | 20 N/A 6 N/A | 21 8200-9 P ...
-
Omnitron Systems Technology 2FXM2 - page 24
From the Chassis V iew menu, select the desired module (select 1 or 5 ), press < ENTER >. The Module configuration screen will be displayed. PI Module - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON condition OFF condition H/W Actual Slot Number = 11 1: Pause Enabled Pause Disabled Off Off Model Number = ...
-
Omnitron Systems Technology 2FXM2 - page 25
4.2 MODULE MANAGEMENT MODE From the Module configuration screen, the management mode can be changed. Select option 18 to change the mode. The management mode options will be displayed. PI Module - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON condition OFF condition H/W Actual Slot Number = 11 1: Pause Enabled ...
-
Omnitron Systems Technology 2FXM2 - page 26
4.3 PORT CONFIGURA TION The Port configuration screen provides access to the port level configuration parameters, such as, Port Access, Bandwidth Control, L2CP Control, SFP information, 802.3ah, Port VLANs, T agged VLANs and cNode Loopback. T o access the Port configuration screen, select C from the Module configuration screen and press <ENTER&g ...
-
Omnitron Systems Technology 2FXM2 - page 27
4.3.1 Port Access The Port Access option allows the ports to be disabled/enabled while maintaining the port configuration and network link T o configure Port Access, select option 11 for the Port 1 and option 12 for the Port 2 from the Port configuration screen. 4.3.2 Bandwidth Control The 2FXM2 Bandwidth Control is accessed by selecting option 8 a ...
-
Omnitron Systems Technology 2FXM2 - page 28
T o change the ingress rate of the Port 1, select option 1 . Change Fiber CIR (range 64 to 100000)> 142 T o change the ingress rate of the Port 2, select option 6 . Change Port 2 CIR (range 64 to 100000)> 100000 T o change the egress rate, select option 4 for Port 1 or option 9 for the Port 2. The egress rates are displayed. Select the desire ...
-
Omnitron Systems Technology 2FXM2 - page 29
4.3.4 SFP Information The 2FXM2 module will provide general and specific information on the SFP . This information is best viewed with SNMP management software. The following is the information available: 4.3.4.1 SFP A0 Information Display This section displays fixed SFP Module information for the following areas. • Identifier V alues • Extende ...
-
Omnitron Systems Technology 2FXM2 - page 30
SFP information can be obtained by selecting option 7 from the Port configuration screen. PI SA SFP Information - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 Port = 1 Address A0 Page Contents =================================================== 00: 03 04 07 00 10 02 00 00 00 00 00 ...
-
Omnitron Systems Technology 2FXM2 - page 31
OAM functions. • 802.3ah OAM Mode - The 802.3ah OAM Mode sets the selected port to “Passive” or “Active” configuration mode. In “Passive” mode the port cannot initiate Discovery , send V ariable Requests or initiate Loopback Mode. It can observe and report only the port status of its 802.3ah enabled remote partner . An “Active” po ...
-
Omnitron Systems Technology 2FXM2 - page 32
ports. If “Forward” is displayed, the remote partner is forwarding non-OAMPDUs to the lower sublayer . If “Discard”, the remote partner is discarding non-OAMPDUs network frames. If “Unknown”, the Multiplexer state of the remote partner is indeterminate. • Parser Action - Indicates the Parser Action state (“Discard”, “Forward”, ...
-
Omnitron Systems Technology 2FXM2 - page 33
4.3.6 802.3ah Event s 802.3ah events can be accessed by selecting options 6 from the Port configuration screen. PI SA 802.3ah Event - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 Port 1 1: Symbol Period Window 0 second < 0 symbols> 2: Symbol Period Threshold 0 symbols 3: Fram ...
-
Omnitron Systems Technology 2FXM2 - page 34
4.3.7 Port VLAN The flow of data on the module is controlled by configuring the Port VLAN settings. The block diagram illustrates the flow of both the management traffic and the data traf fic for a plug-in module (standalone modules do not have backplane access). The data traffic is controlled by a switch matrix which provides complete control of t ...
-
Omnitron Systems Technology 2FXM2 - page 35
Port VLAN is access by selecting options 13 - 22 or 13 - 15 depending on the module type; plug-in or standalone. PI Module - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Port Access Control Setup Slot Number = 1 ---------------------------------- Model Number = 8959N-0 11: Port 1 Enable On 12: Port 2 Enable On Feature S ...
-
Omnitron Systems Technology 2FXM2 - page 36
4.3.8 T agged VLAN The 2FXM2 supports the IEEE 802.1Q tag VLAN packet tagging and un-tagging and the 802.1p Quality of Service priority standards. The following parameters are configured for each port: 4.3.8.1 Port Priority (PRI) This (IEEE 802.1p based) user-specified value of 0 through 7 can be assigned as a QoS priority level ( 0 being lowest an ...
-
Omnitron Systems Technology 2FXM2 - page 37
T agged VLAN is accessed by selecting option 2 from the Port configuration screen. The T ag VLAN Control screen will be displayed. PI Tag VLAN Control - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 Port 1 1: Port Priority (PRI) 0 BP B 16: Port Priority (PRI) 0 2: PVID (Port VLAN ID ...
-
Omnitron Systems Technology 2FXM2 - page 38
4.3.9 VLAN Membership T able The VLAN Membership T able lists the permitted VLAN ID (VID) for each egress port on the module. Only packets that are assigned a VID value that matches one of the egress port’ s VID memberships are allowed to egress through the port. When the Ingress Security is set to High for a specific port, the membership table i ...
-
Omnitron Systems Technology 2FXM2 - page 39
Initially the table is empty . T o configure the ports with VLAN IDs, select option (a) from the VLAN Membership configuration screen. PI Membership Entry - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 VLAN Table Membership Entry 1 ------------------------------ 1: VLAN ID 2 2: Por ...
-
Omnitron Systems Technology 2FXM2 - page 40
T o add a VLAN ID to the membership table, select option 1 and enter the ID #. T o associate the VLAN ID to a port, select the appropriate port option ( 2 - 6 ). PI Membership Entry - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 VLAN Table Membership Entry 1 ----------------------- ...
-
Omnitron Systems Technology 2FXM2 - page 41
Once all the VLAN IDs have been assigned, select option 7 or 5 to save the entries. PI VLAN Membership - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Slot Number = 1 Model Number = 8959N-0 VLAN ID (VID) Port 1 Port 2 BP A BP B Mngmnt 1: 100 Yes No No No No Add new entry (a), Delete entry (d), Edit entry (e), Clear table ...
-
Omnitron Systems Technology 2FXM2 - page 42
4.3.1 1 Port St atistics The 2FXM2 module provides port statistics on both Port 1 and Port 2. The Port Statistics can be viewed by selecting option P from the Module configuration screen. PI Module - iConverter 2FXM2 iConverter, Serial Agent Identifier - Chassis Number = 1 Switch ON condition OFF condition H/W Actual Slot Number = 11 1: Pause Enabl ...
-
Omnitron Systems Technology 2FXM2 - page 43
5.0 2FXM2 SPECIFICA TIONS Plug-i n Module Standal on e T ab let op S tandalone W all -Mount Desc ri pt i on 10 0B A S E -FX Fi be r t o 10 0B A S E -FX Fi b er Co n v erter an d Net work I n terf ace D evice Pr otoc ol s 100BASE-FX w i th 2048 by t es m ax . f ra me siz e Cable T ypes Fiber M u lt imode : 50 /125 , 62. 5/ 125, 100/ 140 u m , Si ngl ...
-
Omnitron Systems Technology 2FXM2 - page 44
6.0 TROUBLESHOOTING GUIDE 6.1 OVERVIEW The 2FXM2 module has several LED indicators available to assist in the determination of problems. Refer to Section 3.5, V erify Operation, for LED definitions. 6.1.1 Power Issues Problem: The Power LED does not illuminate after installation is complete or no LED indicators ar e ON Possible Causes: A. For stand ...
-
Omnitron Systems Technology 2FXM2 - page 45
7. 0 WARRANTY This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. T O REGISTER, COMPLETE AND MAIL OR F AX T ...
Haben Sie eine Frage bezüglich Omnitron Systems Technology 2FXM2?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Omnitron Systems Technology 2FXM2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Omnitron Systems Technology 2FXM2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.