Bedienungsanleitung Impex MWM 1801

29 Seiten 4.14 mb
Download

Zur Seite of 29

Summary
  • Impex MWM 1801 - page 1

    NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Pack Assembly Instruc tion Parts L ist Resistance Chart Warranty Ordering Parts Model MW M 1801 Retain This Manual for Reference 08-18-03 OWNER'S MANUAL MARCY HOME GYM MWM 1801 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF ...

  • Impex MWM 1801 - page 2

    TA BLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFET Y NOTICES...................................................................……….. 2 HARDW ARE PACK……….....….....................................................................……….. ...

  • Impex MWM 1801 - page 3

    IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine. In particul ar, note the follow ing safety precautions: 1. Keep children and pets away ...

  • Impex MWM 1801 - page 4

    HARDWARE PACK 3 ...

  • Impex MWM 1801 - page 5

    HARDWARE PACK 4 ...

  • Impex MWM 1801 - page 6

    A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Attach the Lef t Base Frame (#3) to the Ri ght Base Frame ( #1). Secure them w ith one Bracket (#47), t ...

  • Impex MWM 1801 - page 7

    STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#2) to the Ri ght Base Frame ( #1). Secure it w ith two M10 x 2 ½” Carri age Bolts ( #82), ∅ ¾” W ashers (#93), and M10 Ai rcraft Nuts (#90) . NOTE: Do not tighten the N uts and Bolts yet. B.) Attach the Right Seat Support (#8) to the Right Base Fr ame (#1). Secure it wi th one M10 ...

  • Impex MWM 1801 - page 8

    STEP 3 (See Diagram 3) A.) Alig n four ∅ 2 ½ ” x 1” Rubber Bumper s (#68) to the holes on the R ight Base Fr ame (#1). Insert four Gui de Rods (#5) thr ough the Rubber Bumpers into the holes on the Right Base Fr ame. Slide tw o Selector Stems (#35) onto the Guide Rods. Insert a Selector Rod ( #24) throug h the hole on each Selector Stem. Sec ...

  • Impex MWM 1801 - page 9

    DIAGRAM 3 8 ...

  • Impex MWM 1801 - page 10

    STEP 4 (See Diagram 4) A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3) . Secure it w ith two M10 x 2 ½ ” Carriage Bol ts (#82), ∅ ¾” W ashers (#93), and M 10 Aircr aft Nuts (#90). B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left Vertical Beam. Secur e the Frame to the Lef t Vertical Beam ...

  • Impex MWM 1801 - page 11

    DIAGRAM 4 10 ...

  • Impex MWM 1801 - page 12

    STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure i t wi th a M10 x 9 ¼ ” Axle (#50), tw o ∅ ¾” W ashers (#93), and tw o M10 Aircraft Nuts (#90). B.) Attach the two Front Presses (#16) to the Front Press Base (#15) . Secure each Front Press w ith two M10 x 2 ½ ” Carr iage Bolts ( #82), two ? ...

  • Impex MWM 1801 - page 13

    STEP 6 (See Diagram 6) A.) Insert the axle on the Left Butterfly ( #12) throug h the hole on the Left Upper Frame (#11) from the bottom up. Sli de a ∅ 1 ½” W asher (#54) and ∅ 1 3/8” Lock Ri ng (#53) onto the Axle. Al ign the hol es and secure the Ring wi th a M6 x 1 5/8” Hex Bolt (#87) and M6 Aircr aft Nut (#91). Repeat the same pr oced ...

  • Impex MWM 1801 - page 14

    Cable Loop Diagram f or Butterfly Stat ion 13 ...

  • Impex MWM 1801 - page 15

    Cable Loop Diagram f or Bench Press Station 14 ...

  • Impex MWM 1801 - page 16

    STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the two Swiv el Pulley Brackets ( #42) to the Left Upper Frame ( #11). Secure each Bracket w ith one M12 x 4 3/8” Allen Bol t (#76), tw o ∅ 1” W ashers (#92) and one M12 Air craft Nut (#89). NO TE: Do not over tig hten the Bolt. Make sure the Bracket is able to sw ivel. B.) Attach one ...

  • Impex MWM 1801 - page 17

    STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach a Chain (#51) to the Left Vertical Beam (#4) . Secure it w ith one M10 x 1 3/8” Allen Bolt ( #83), tw o ∅ 3/4” W ashers (#93), and one M10 Aircr aft Nut (#90). Attach one end of the 136” Butterfly Support C able (#31) to the C hain using a C-cli p (#63). NOTE: After complete install ...

  • Impex MWM 1801 - page 18

    STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the140” Leg Press C able (#28) to the openi ng hole on the Left Seat Support (#14), under neath the rubber bumper . Secure it w ith one M10 x 2 3/8” All en Bolt (#79), tw o ∅ ¾” W ashers (#93), and one M 10 Aircraft Nut ( #90). B.) Draw the Cabl e to the slotted opening ...

  • Impex MWM 1801 - page 19

    DIAGRAM 9 18 ...

  • Impex MWM 1801 - page 20

    STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#26) to the f ront opening on the Ri ght Upper Frame (#6). NOTE: The Ball Stopper on the Cabl e needs to be underneath the Frame. B.) Attach a Pulley (#65) to the opening. Secure i t wi th one M10 x 2 3/8” Allen Bol t (#79), tw o ∅ 5/8” x ½ ” Pulley Bushin ...

  • Impex MWM 1801 - page 21

    STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach a Pulley to the opening. Secur e the Pulley wi th one M10 x 2 3/8” Allen Bol t (#79), tw o ∅ 5/8” x ½ ” Pulley Bushing s (#58), and one M 10 Aircr aft Nut (#90). B.) Pull the AB Cable around the Pull ...

  • Impex MWM 1801 - page 22

    DIAGRAM 11 21 ...

  • Impex MWM 1801 - page 23

    STEP 12 (See Diagram 12) A.) Now move the machine to its fina l p o sition. Af ter insta llin g th e weight stack, it will be too he avy to move. Check and ti ghten all N uts and Bolts prev iously installed. B.) Install 9 W eight Plates (#36) to each set of Guide Rods (#5). To install the pl ate, lift up the Selector Rod i n the center, hold the pl ...

  • Impex MWM 1801 - page 24

    STEP 13 (See Diagram 13) A.) Insert one Foam Tube (#34) halfway through the hol e on the Rig ht Seat Support (#8) . Insert one Foam Tube (#34) halfway through the hole on the Leg D eveloper (#9). Push four Foam Rolls ( #38) onto the Tubes from both sides. Plug the Foam R oll End Caps ( #74) into the ends. B.) Attach the Lat Bar (#20) to the Chain ( ...

  • Impex MWM 1801 - page 25

    STEP 14 (See Diagram 14) A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secur e it wi th two M 8 x 2 1/8” Allen Bolts ( #84) and ∅ 5/8” W ashers (#94). B.) Place the Seat (#22) onto the Left Seat Support (#14). Secur e it w ith two M 8 x 2 1/8” Allen Bolts (#84) and tw o ∅ 5/8” W ashers (#94). C.) Attach the Leg Press ...

  • Impex MWM 1801 - page 26

    HOW TO USE How to u se the qu ick release con nector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Insert Push down the Clip to secure. 25 ...

  • Impex MWM 1801 - page 27

    PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Fram e 1 2 Right Vertical Beam 1 3 Left Base F ram e 1 4 Left Vertic al Beam 1 5 Guide Rod 4 6 Right Upper Fram e 1 7 Top Soc ket As sem bly 1 8 Right Seat Support 1 9 Leg Developer 1 10 Arm Curl Stand 1 11 Left Upper Fr am e 1 12 Left Butterf ly 1 13 Right Butterfly 1 14 Left Seat Support 1 15 Fro ...

  • Impex MWM 1801 - page 28

    MWM 1801 Weight Resistance Chart Weight Plate Station 1 2 3 4 5 6 7 8 9 Low Pulley 30 42 54 66 78 90 102 114 126 Lat Pu ll 31 42 53 64 75 86 97 108 119 Ab Strap 30 42 54 66 78 90 102 114 126 Butterfly 20 26 32 38 44 50 56 62 68 Leg Press 66 100 134 168 202 236 270 304 338 Front Press 44 63 82 101 120 139 158 177 196 *Each plate weights 10 lb. *Resi ...

  • Impex MWM 1801 - page 29

    IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and s ervic e conditions , f or a per iod of two years on the F ram e f r om the date of purchase. T his warr anty extends only to the original purchaser . IMPEX 's obligation under thi ...

Produzent Impex Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Impex MWM 1801 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Impex
- Bedienungsanleitungen MWM 1801
- Produktkarten Impex
- Informationsbroschüren
- oder Energieetiketten Impex MWM 1801
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Impex MWM 1801.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Impex MWM 1801, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Impex MWM 1801. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Impex MWM 1801 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Impex MWM 1801, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Impex MWM 1801 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Impex MWM 1801 verständlich ist.

Eine gänzliche Bedienungsanleitung von Impex sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Impex MWM 1801 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Impex MWM 1801 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Impex MWM 1801, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Impex MWM 1801 - die uns die ersten Schritte während der Nutzung von Impex MWM 1801 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Impex MWM 1801 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Impex MWM 1801 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Impex MWM 1801?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Impex MWM 1801 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Impex MWM 1801 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)