Deutsch dropdown-ico

Bedienungsanleitung InFocus IN5122

34 Seiten 1.66 mb
Download

Zur Seite of 34

Summary
  • InFocus IN5122 - page 1

    RS232 Command and Control Guide Regulatory models: W60, W61 010-0763-00 DISPERINDAG No. 0287/1.824.51/09.03 ...

  • InFocus IN5122 - page 2

    This page left blank intentionally ...

  • InFocus IN5122 - page 3

    1 Projector IN5122/IN5124 RS232 Command and Control Guide The signals listed on the following pages are used for initial setup, however the signal timings of some computer models may be different. In such a case, adjust V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data D ...

  • InFocus IN5122 - page 4

    2 Initial set signals Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 ...

  • InFocus IN5122 - page 5

    3 Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 525 480 2 33 640x48 ...

  • InFocus IN5122 - page 6

    4 A COMPUTER IN1, B MONITOR OUT D-sub 15pin mini shrink jack <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V . sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level <Component video signal> • Video signal: - Y, Analog, 1.0±0.1Vp-p with composite sync, 7 ...

  • InFocus IN5122 - page 7

    5 E S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (P AL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the por ts (continued) 4 3 2 1 F VIDEO RCA jack ...

  • InFocus IN5122 - page 8

    6 Connection to the por ts (continued) H AUDIO IN1, I AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms, 47kΩ terminator J AUDIO IN3 (R, L) K AUDIO OUT (R, L) RCA jack x2 RCA jack x2 • 200 mV rms, 47kΩ terminator • 200 mV rms, 1kΩ output impedance L MIC Ø3.5 mono mini jack <Low level> • 2 mV rms, 1kΩ terminator <High level> ...

  • InFocus IN5122 - page 9

    7 Connection to the por ts (continued) O USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground 4 3 1 2 P CONTROL D-sub 9pin plug • About the details of RS-232 communication, please refer to the section "RS-232 Communication". Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS ...

  • InFocus IN5122 - page 10

    8 SCART T o input SCART RGB signal; ex. Connection to the por ts (continued) T o input SCART RGB signal to the projector , use a SCART to RCA cable. Connect the plugs refer to above example. For more reference, please consult your dealer . SCART connector (jack) SCART cable (plug) RCA plugs ...

  • InFocus IN5122 - page 11

    9 CD (1) (1) -- RD(2) (2) RD TD (3) (3) TD DTR (4) (4) -- GND (5) (5) GND DSR (6) (6) -- R TS (7) (7) R TS DTS (8) (8) CTS RI (9) (9) -- RS-232 Communication RS-232 Communication When the projector connects to the computer by RS-232 communication, the projector can be controlled with RS-232 commands from the computer . For details of RS-232 command ...

  • InFocus IN5122 - page 12

    10 Command Control via the Network When the projector is connected to the network, the projector can be controlled with RS-232 commands from the computer with a web browser . For RS-232 command information, refer to the RS-232 Communication / Network command table ( & 16 ). Connection 1. T urn of f the projector and the computer . 2. Connect th ...

  • InFocus IN5122 - page 13

    11 Communication P or t The following port is assigned for command control. TCP #23 Congure the following items from a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”. Authenti ...

  • InFocus IN5122 - page 14

    12 Command Control via the Networ k (continued) RS-232 Commands IMPORT ANT : When formatting commands sent from a control system or computer , enclose commands in parentheses “(“ and “)”. When entering custom commands into Scheduled T asks in the projector ’s web interface, enclose commands in less than/ greater than symbols “<” an ...

  • InFocus IN5122 - page 15

    13 Command Control via the Networ k (continued) A write request example: (AAA####) where (starts the command AAA denotes the command #### denotes the value to be written (leading zeros not necessary) ) ends the command Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically s ...

  • InFocus IN5122 - page 16

    14 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232 communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide . Connection 1. ...

  • InFocus IN5122 - page 17

    15 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICA TION menu. ( & OPTION menu - SERVICE - COMMUNICA TION in the User's Manual ) Item Condition BAUD RA TE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (xed) P ARITY NONE/ODD/EVEN Start bit 1 bit (xed) Stop bit 1 bit (xed) T ransmiss ...

  • InFocus IN5122 - page 18

    16 RS-232 Communication / Network command table RS-232 Communication / Netw ork command ta ble Function Command RW Min Max Default Step BASIC MENU Aspect Ratio 0: Auto 1: Native (IN5124 only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Auto Keystone Execute 1: Execute AV K W 0 1 n/a Horizontal Keystone DKH RW 38 218 128 1 V ertical Keystone DKV RW 38 218 ...

  • InFocus IN5122 - page 19

    RS-232 Communication / Netw ork command ta ble (continued) 17 (continued on next page) Function Command RW Min Max Default Step Presets 1: User 5: Presentation 7: Video 10: Bright 1 1: Whiteboard 12: Blackboard 13: Greenboard 15: Dynamic PST RW 1 15 5 (Computer in 1) 5 (Computer in 2) 5 (LAN) 5 (USB T ype A) 5 (USB T ype B) 15 (HDMI) 15 (Component) ...

  • InFocus IN5122 - page 20

    RS-232 Communication / Netw ork command ta ble (continued) 18 (continued on next page) Function Command RW Min Max Default Step Gamma 32: 1 Default 16: 1 Custom 33: 2 Default 17: 2 Custom 34: 3 Default 18: 3 Custom 35: 4 Default 19: 4 Custom 36: 5 Default 20: 5 Custom 37: 6 Default 21: 6 Custom GTB RW 16 37 32 (Computer in 1) 32 (Computer in 2) 32 ...

  • InFocus IN5122 - page 21

    RS-232 Communication / Netw ork command ta ble (continued) 19 (continued on next page) Function Command RW Min Max Default Step Gamma Custom-4 Point 7 G41 RW 11 2 144 128 1 Gamma Custom-4 Point 8 G42 RW 11 2 144 128 1 Gamma Custom-5 Point 1 G43 RW 11 2 144 128 1 Gamma Custom-5 Point 2 G44 RW 11 2 144 128 1 Gamma Custom-5 Point 3 G45 RW 11 2 144 128 ...

  • InFocus IN5122 - page 22

    RS-232 Communication / Netw ork command ta ble (continued) 20 (continued on next page) Function Command RW Min Max Default Step Color T emperature - 6 Blue Gain BG6 RW 96 160 128 1 Color T emperature - 1 Red Offset RF1 RW 96 160 128 1 Color T emperature - 2 Red Offset RF2 RW 96 160 128 1 Color T emperature - 3 Red Offset RF3 RW 96 160 128 1 Color T ...

  • InFocus IN5122 - page 23

    RS-232 Communication / Netw ork command ta ble (continued) 21 (continued on next page) Function Command RW Min Max Default Step ADV ANCED MENU: IMAGE Aspect Ratio 0: Auto 1: Native (IN5124 Only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Overscan 0: Off 1: Zoom 2: Crop OVS RW 0 2 0 V ertical Position VPS RW if def<128: 0 else: def -128 def +128 auto 1 ...

  • InFocus IN5122 - page 24

    RS-232 Communication / Netw ork command ta ble (continued) 22 (continued on next page) Function Command RW Min Max Default Step S-Video Standard 0: Auto 1: NTSC 2: P AL 3: SECAM 4: NTSC4.43 5: M-P AL 6: N-P AL ? RW 0 6 0 HDMI Format 0: Auto 1: Video 2: Computer RW 0 2 0 HDMI Range 0: Normal 1: Enhanced 16: Auto RW 0 16 16 Component 0: Component 1: ...

  • InFocus IN5122 - page 25

    RS-232 Communication / Netw ork command ta ble (continued) 23 (continued on next page) Function Command RW Min Max Default Step Corner Correction all corners Reset 0: n/a 1: enable CNR RW 0 1 n/a Side Correction Left Gain SC1 RW 98 158 128 1 Side Correction Right Gain SC2 RW 98 158 128 1 Side Correction V Position SC3 RW 0 768 (IN5122) 800 (IN5124) ...

  • InFocus IN5122 - page 26

    RS-232 Communication / Netw ork command ta ble (continued) 24 (continued on next page) Function Command RW Min Max Default Step Monitor Out for Source 5 (HDMI) 1: Computer in 1 2: Computer in 2 255: Off SM5 RW 1 255 1 Monitor Out for Source 6 (Component) 1: Computer in 1 2: Computer in 2 255: Off SM6 RW 1 255 1 Monitor Out for Source 7 (S-Video) 1: ...

  • InFocus IN5122 - page 27

    RS-232 Communication / Netw ork command ta ble (continued) 25 (continued on next page) Function Command RW Min Max Default Step Audio for Source 0 (Computer in 1) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA0 RW 0 5 0 Audio for Source 1 (Computer in 2) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA1 RW 0 5 1 Audio for Source 2 (LAN) 0: Audio 1 1: Audio ...

  • InFocus IN5122 - page 28

    RS-232 Communication / Netw ork command ta ble (continued) 26 (continued on next page) Function Command RW Min Max Default Step HDMI Noise Cancel 0: Disable 1: Enable HNC RW 0 1 1 MIC Level 0: Low 1: High MIK RW 0 1 0 MIC V olume MIC RW 0 48 24 1 ADV ANCED MENU: SCREEN Menu Positon H OFH RW 0 10 0 (left) 1 Menu Positon V OFV RW 0 10 10 (top) 1 Blan ...

  • InFocus IN5122 - page 29

    RS-232 Communication / Netw ork command ta ble (continued) 27 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Auto Power 0: Disable 1: Enable AOT RW 0 1 0 USB T ype B 0: Mouse 1: USB Display USB RW 0 1 1 Custom Key (Effect) 0: Blank 1: Mute 2: Aspect Ratio 3: Source 4: Aut ...

  • InFocus IN5122 - page 30

    RS-232 Communication / Netw ork command ta ble (continued) 28 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Source 4 0: Computer in 1 1: Computer in 2 2: LAN 3: USB T ype A 4: USB T ype B 5: HDMI 6: Component 7: S-Video 8: Video SR4 RW 0 8 8 Power-up Source 0: Computer i ...

  • InFocus IN5122 - page 31

    RS-232 Communication / Netw ork command ta ble (continued) 29 (continued on next page) Function Command RW Min Max Default Step My Image Display 0: Off 1: Image-1 2: Image-2 3: Image-3 4: Image-4 MIF RW 0 4 0 My Image Delete Image-1 1: delete MD1 W 0 1 n/a My Image Delete Image-2 1: delete MD2 W 0 1 n/a My Image Delete Image-3 1: delete MD3 W 0 1 n ...

  • InFocus IN5122 - page 32

    RS-232 Communication / Netw ork command ta ble (continued) 30 (continued on next page) Function Command RW Min Max Default Step Freeze 0: Off 1: On FRZ RW 0 1 0 INFOCUS UNIQUE About (Source Info) 0: n/a 1: enable ABT W 0 1 n/a Lamp Lit 0: not lit 1: lit LML R 0 1 0 Number of Lamp Resets LMR R 0 32766 0 Lamp T otal On T ime (All Bulbs) LMT R 0 21474 ...

  • InFocus IN5122 - page 33

    31 PJLink command PJLink command POWR Power Control 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B INPT ? Input Source inquiry 1 1 = COMPUTER IN 1 1 ...

  • InFocus IN5122 - page 34

    32 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte : Refers to Lamp error; one of 0 to 2 3rd byte: Refers to T emperature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 ...

Produzent InFocus Kategorie Projector

Dokumente, die wir vom Produzenten des Geräts InFocus IN5122 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen InFocus
- Bedienungsanleitungen IN5122
- Produktkarten InFocus
- Informationsbroschüren
- oder Energieetiketten InFocus IN5122
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung InFocus IN5122.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen InFocus IN5122, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen InFocus IN5122. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts InFocus IN5122 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts InFocus IN5122, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von InFocus IN5122 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von InFocus IN5122 verständlich ist.

Eine gänzliche Bedienungsanleitung von InFocus sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von InFocus IN5122 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von InFocus IN5122 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich InFocus IN5122, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts InFocus IN5122 - die uns die ersten Schritte während der Nutzung von InFocus IN5122 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit InFocus IN5122 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von InFocus IN5122 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich InFocus IN5122?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit InFocus IN5122 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit InFocus IN5122 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)