Deutsch dropdown-ico

Bedienungsanleitung Troy-Bilt 630CN

32 Seiten 2.97 mb
Download

Zur Seite of 32

Summary
  • Troy-Bilt 630CN - page 1

    O TRO_ BILT Operator's Manual Rear-tine Tiller Models 630Cn Tuffy _ 634Fm BroncoTM 634Bm Super BroncoTM Model 634B Shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land ...

  • Troy-Bilt 630CN - page 2

    TABLE OF CONTENTS Content Page Calling Customer Support ....................................................................................................... 2 Safety ...................................................................................................................................... 3 Assembly.................................... ...

  • Troy-Bilt 630CN - page 3

    SECTION 1: SAFETY This machine meetsvoluntary safety stan- dard B71.8-1996, whichis sponsored bythe Outdoor PowerEquipment Institute,Inc., and is published bythe AmericanNational Standards Institute. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproduc- Saf ...

  • Troy-Bilt 630CN - page 4

    4. Exercise caution to avoid slipping or fall- If in doubtabout the tilling conditions,al- 24. Do not touch engine parts which may ing. 5. If the unit should start to vibrate aonor- really,stop the enQne. disconnect the spark plug wire and prevent it from touch- ing the spark plug, and check immediately for the cause. Vibration is generally a warni ...

  • Troy-Bilt 630CN - page 5

    Decals For your safety and the safety of others, vari- ous safety and operationa! decals are located on your unit (see Figure 1-2). Keepthe decals clean and legible at all times. Contactyour local service dealer or the factory for replacements if any decals are damaged or missing. Referto the Parts List pages in this Manual for decal locations, des ...

  • Troy-Bilt 630CN - page 6

    SECTION 2: ASSEMBLY WARNING: To prevent personal injury or property damage,do not start the engine until all assembly steps are complete and you have read and understandthe safety and operating instructions in this manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It _s recommended that you read th ...

  • Troy-Bilt 630CN - page 7

    Fig. 2=3: Wheel in FREEWHEEL position STEP 4: INSTALL FORWARD CLUTCH CABLE 1. Attach the forward clutch cable bracket (P, Fig. 2-4) to the handlebar support AI with a 1/4"-20 x 1-1/4" hex hd. screw (R) and 1/4"-20 hex Iocknut (S). Tighten se- curely. 2. Carefully unwrap the forward clutch ca- ble (cable without an attached knob, from ...

  • Troy-Bilt 630CN - page 8

    4.Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V). 5. Thread the screw IVI into the cable ad- juster (X). 6. Hook the cable spring (W, Fig.2-6) into the V-shaped bend in the Forward Clutch Bail 7. Checkfor correct tension on the forward drive belt by taking two measurements of the cable spring, as follows: a. With the Forward Clu ...

  • Troy-Bilt 630CN - page 9

    31bY I_: UI'IEUK LEVEL UI- The transmission was filled with gear oil at the factory. However,you should check the gear oil level at this time to makecertain it is correct. IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmission com- ponents. 1. With the tiller on level ground ...

  • Troy-Bilt 630CN - page 10

    SECTION 3: FEATURES AND CONTROLS WARNING: Before operating your machine, carefully readand understand all safety, controls and operating instructions in this Manual, the separateEngine Owner's Manual,and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. INTRODUCTION This Section describes ...

  • Troy-Bilt 630CN - page 11

    Figure 3-3: FREEWHEEL position. WARNING: Use extreme caution when reversing or pulling the machine towards you. Look behind to avoid obstacles. Neverattempt to till in reverse. Failure to follow this warning could result in personal injury or property damage. To operate the Reverse ClutchControl: 1. Put wheels in WHEELDRIVE position (see "WARN ...

  • Troy-Bilt 630CN - page 12

    SECTION 4: OPERATION WARNING: Before Reverse Clutch Control operating your machine, (Models 634F/634B) carefully readand understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, the separate Engine Owner's Manual,and on the Clutch Bail decals on the machine. Failure to follow these instruct ...

  • Troy-Bilt 630CN - page 13

    KEEP AWAY F_OM ROTATING 11NES. ROTATING 11NE$ WILL CAUSE INJURY. Stopping the Engineand Tiller 1. To stop the wheels and tines, release the Forward Clutch Bail (all models) or the Re- verse Clutch Control (Models 634F and 634B) -- whichever control is in use. 2. To stop the engine, put the ignition switch and/or the throttle control lever in the &q ...

  • Troy-Bilt 630CN - page 14

    TILLING TIPS & TECHNIQUES Tilling Depths _=i, WARNING: Before A L • tilling, Contactyour m, m. telephone or utilities company and inquire if underground equipment or lines are used on your property. Do not till near buried electric cables, • Avoid pushing down on the handlebars in an attemptto force the tillerto dig deeper• Doing so takes ...

  • Troy-Bilt 630CN - page 15

    TILLING TIPS & TECHNIQUES (CON'T) PowerComposting Power composting simply means tilling underand burying in the soil all manner of organic WARNING: When power matter such as crop residues, leaves, grassclippings and cover crops. This materialwill de- composting, do not keep the compose during the non-growing seasonand add important natural ...

  • Troy-Bilt 630CN - page 16

    TILLING TIPS & TECHNIQUES (CON'T) Terrace Gardening(continued) • To create a terrace, start at the top of the slope and work down.Go backand forth across the first r0w as shown in Fig.4-!0. • Eachsucceedinglowerterraceisstartedbywalkingbelowtheterraceyou'repre- 0_11_1__..,..___,_,,. __ paring. For addedstability of the tiller, alw ...

  • Troy-Bilt 630CN - page 17

    SECTION 5: MAINTENANCE WARNING: Before inspecting, cleamng or serwcmg the machine, shut off engine. wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition keyon electric start models. Failure to follow these instructions can result in serious personal injury or property d ...

  • Troy-Bilt 630CN - page 18

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. 4. The gear oil level is correct if the gear oil is approx ...

  • Troy-Bilt 630CN - page 19

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. C FRONT/ FORWARD b Unthread the hex nut IC, Figure 5-4) ha ...

  • Troy-Bilt 630CN - page 20

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. FORWARD CLUTCH BAIL ADJUSTMENT If the Forward Clutch Bail ...

  • Troy-Bilt 630CN - page 21

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. 3. Clean around the oil dipstick or oil fill tube (whichev ...

  • Troy-Bilt 630CN - page 22

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. TROUBLESHOOTING PROBLEM Engine does notstart Engine runs p ...

  • Troy-Bilt 630CN - page 23

    SECTION 6: MODELS 630C,634F & 634B PARTS LIST 13 3 i 15 19 14 12 9 8_ _ _" 1_ (A) For Model 630C _ .._ "" (B) For Model 634F _'_ (C) For Model 634B REF PART NO. NO. 1 1185469 2 710-0597 3 710-0599 4 710-0874 5 710-3039 6 712-0291 7 712-3004A 8 712-3009 9 736-0119 10 GW-55013-1 11 GW-55013-2 REF DESCRIPTION PART NO. NO. Spi ...

  • Troy-Bilt 630CN - page 24

    MODELS 630C, 634F & 634B 2 5 2O 22 / 15 16 ! ! 20 E 18 / 14 / 23 7 8 18 25 7 20 24 ...

  • Troy-Bilt 630CN - page 25

    MODELS 630C, 634F & 634B REF NO. 1 1916719 2 1916755 3 1917479 4 1918745 5 710-0599 6 710-3008 7 712-3009 8 GW-55042 9 GW-55043 10 GW-55102 11 GW-55044 12 GW-9855 13 725-0157 14 736-3050 15 1916674 16 1916712 17 710-0106 18 710-0216 20 710-0805 21 712-0121 22 712-0291 23 712-3000 25 736-0119 PART NO. DESCRIPTION Cable Assembly, Reverse Clutch(B ...

  • Troy-Bilt 630CN - page 26

    MODELS 630C, 634F & 634B 4 _ / 1 / / (A) For Model 6300 (B) For Model 634F (C) For Model 6348 REF NO. 1 GW-9517 2 GW-1714 3 GW-50043 4 1904277 5 GW-1224-1" GW-1224-2" GW-1224-3 * GW-1224-4" -- GW-13250 PART NO. DESCRIPTION Snap Ring Bearing, Tapered Roller (with race) Support Washer, Rear Drive Shaft(A) (B) (C) Shim,Rear Bearing ...

  • Troy-Bilt 630CN - page 27

    MODELS 630C, 634F & 634B FRONT 8 11 3 4 (A) For Model 6300 (B) For Model 634F (C) For Model 6348 REF PART NO. NO. 1 GW-9512 2 1909950 3 GW-1166-1" GW-1166-2" GW-1166-3" GW-1166-4" GW-1166-5" GW-1086 1916741 GW-55004 GW-9305 GW-1132-2 1904278 1915074 GW-1104 1904279 6 7 8 9 10 11 7 4 3 DESCRIPTION Retainer, Snap Ring, &q ...

  • Troy-Bilt 630CN - page 28

    MODELS 630C, 634F & 634B 10 10 14 * included with transmission when purchased as an assembly only, Remove and discard when installing the transmission on tiller. REF PART NO. NO. 1 GW-9727 2 710-04049 3 736-0119 4 1918377 5 1916641 6 GW-50032 7 GW-9617 DESCRIPTION Plug, Transmission Oil Fill Hex Hd. Flange Screw, 5/16-18 x 5/8,G r. 5 Lock Washe ...

  • Troy-Bilt 630CN - page 29

    MODELS 630C, 634F & 634B Hold Tines With Blunt End Toward You LEFT-HAND TINE RIGHT-HAND TINE NOTE: Ideotib Left and Right sides of tiller bj standing _n operator position and facing direction of forward travel. 11 2 WHEEL SHAFT 7_6' TINE SHAFT 11 3 1" Used on Left side of tiller :j:Used on Right side of tiller (A) For Model 630C (B) F ...

  • Troy-Bilt 630CN - page 30

    MODELS 630C, 634F & 634B 31 38 17 5 24 24' 3O ...

  • Troy-Bilt 630CN - page 31

    MODELS 630C, 634F & 634B REF NO. 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 43 PART NO. DESCRIPTION 1107382 1108841 1916531 GW-55035 1916532 GW-55031 1916535 1916652 1916657 GW-55037 1916658 1916660 1916724 1916725 1916726 1916794 1916795 1917326 1917746 1918731 1918744 710 ...

  • Troy-Bilt 630CN - page 32

    TROY-BILT TILLER LIFETIME LIMITED WARRANTY WHATPRODUCT ISCOVERED All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the odgina[ purchaser only. WHAT IS COVERED Troy-Bilt LLC will, at its option, repair or rep ...

Produzent Troy-Bilt Kategorie Tiller

Dokumente, die wir vom Produzenten des Geräts Troy-Bilt 630CN erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Troy-Bilt
- Bedienungsanleitungen 630CN
- Produktkarten Troy-Bilt
- Informationsbroschüren
- oder Energieetiketten Troy-Bilt 630CN
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Troy-Bilt 630CN.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Troy-Bilt 630CN, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Troy-Bilt 630CN. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Troy-Bilt 630CN ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Troy-Bilt 630CN, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Troy-Bilt 630CN hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Troy-Bilt 630CN verständlich ist.

Eine gänzliche Bedienungsanleitung von Troy-Bilt sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Troy-Bilt 630CN bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Troy-Bilt 630CN befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Troy-Bilt 630CN, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Troy-Bilt 630CN - die uns die ersten Schritte während der Nutzung von Troy-Bilt 630CN erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Troy-Bilt 630CN hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Troy-Bilt 630CN im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Troy-Bilt 630CN?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Troy-Bilt 630CN nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Troy-Bilt 630CN hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)