-
Paradyne 5216 - page 1
TM 1 Hotwire 5216 Remote T ermination Unit (RTU) Customer Premises Installation Instructions Document Number 5216-A2-GN10-10 February 1998 Before Y ou Begin An optional POTS (Plain Old T elephone Service) splitter is available for the 5216 RTU. When a POTS splitter is installed, the telephone and 5216 RADSL (Rate Adaptive Digital Subscriber Line) R ...
-
Paradyne 5216 - page 2
2 Package Checklist V erify that your package contains the following: - Model 5216 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 modular plugs - Power cord with power transformer - T wo ferrite chokes - W arranty card Refer to Cables & Connectors , page 13, for standard pin numbers. What Does the Hotwire R TU Do? The 5216 RTU ...
-
Paradyne 5216 - page 3
3 When a POTS splitter is used at both ends of the local loop, wiring is connected: H From the demarcation point to the CP POTS splitter , and H From the demarcation point to the DSL jack. 97-15608 Punchdown Block or NID DSL Jack RT U New Wiring Connections Existing Wir ing (PO TS) Customer Premises (CP) DSL Ethernet Crossov er Cable Central Office ...
-
Paradyne 5216 - page 4
4 DSL Access without a POTS Splitter When the 5216 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access. 97-15609 Punchdown Block or NID DSL Jack RT U Customer Premises (CP) PO TS DSL Ethernet Crossov er Cable Central Office (CO) Demarcation P oint Local Loop New Wiring Connections Existing Wir ing (PO ...
-
Paradyne 5216 - page 5
5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations. " Procedur e 1. Access t ...
-
Paradyne 5216 - page 6
6 Green (T1) and red (R1) are the standard wiring colors used in the next two illustrations. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access. The POTS pair for the existing POTS line wiring does not need to be disconnected unless a POTS splitter is going ...
-
Paradyne 5216 - page 7
7 2. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. T ighten both terminal screws with a flat-blade screwdriver . DSL/PO TS Access from Local Loop Wiring to DSL Jac k T elephone Network Interface Device (NID) Ground Tip T1 (Green) Ring R1 ...
-
Paradyne 5216 - page 8
8 DSL Jack Installation The 5216 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 jack. The RJ1 1 6-pin jack us ...
-
Paradyne 5216 - page 9
9 Installing the R TU Place the 5216 RTU on a flat surface with clearance for the rear connectors. " Procedur e 1. Use the RJ1 1 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL. 97-15300-01 DSL Jack POWER ETHERNET DSL Hotwire RTU 2. Use an 8-pin Ethe ...
-
Paradyne 5216 - page 10
496-14952 97-15303c Ethernet Line PO WER ETHERNET DSL Hotwire RTU F err ite Choke 10 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown. 4. Close the two halves around the cable and snap the ferrite choke shut. Press down on the ...
-
Paradyne 5216 - page 11
11 6. Close the two halves around the cable and snap the ferrite choke shut. Press down on the plastic latch to secure the ferrite choke in place around the cable. 7. Plug the transformer into an AC outlet. The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test. Power -On When powe ...
-
Paradyne 5216 - page 12
12 LED Status Condition DSL Blinking ON OFF RTU is establishing the DSL link. The LED blinks on and off about five times per second. The DSL link is now active and ready to transmit and receive data. The DSL link has not been established. ETHERNET ON OFF The Ethernet 10BaseT connection to the end-user system is active. No Ethernet 10BaseT device is ...
-
Paradyne 5216 - page 13
97-15304 6- P i n RJ 1 1 Pl ug DS L Li ne Pi n #1 Pi n #6 13 LED Symptom Action DSL and Ethernet LEDs are on and there is no data transmission. The DSL link and the Ethernet link have been established. If the problem continues, contact the NSP . Ethernet LED is off. V erify that the Ethernet 10BaseT cable is securely installed at both ends, and tha ...
-
Paradyne 5216 - page 14
14 H The Ethernet interface crossover cable connector uses an 8-pin, non-keyed modular plug. 97-15305 8- P i n Pl u g E t he r ne t Ca bl e Pi n #1 Pi n #8 10BaseT TX D + 10BaseT TX D 10BaseT R X D + No t Us ed No t Us ed 10BaseT R X D No t Us ed No t Us ed 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 10BaseT TX D + 10BaseT TX D 10BaseT R X D + No t ...
-
Paradyne 5216 - page 15
15 Model 5216 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.35 ″ x 6.00 ″ x 8.75 ″ (3.43 cm x 15.35 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 T ransformer normal service input voltage range Input: 100 V ac, 50 Hz; 120 V ac, 60 Hz; or 230 V ac, 50/60 Hz Output: 15 Vdc nominal (+ 10%), minimum 0.6A ...
-
Paradyne 5216 - page 16
16 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do n ...
-
Paradyne 5216 - page 17
17 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: H Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the member states relating to electrical equipment designed for use within states relating to ...
-
Paradyne 5216 - page 18
18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5216-A2-200 This device complies with Part 15 of the FCC Rules. Operat ...
-
Paradyne 5216 - page 19
19 EMI W arnings ! W ARNING: T o Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada. Notice to Users of the Canadian T elephone ...
-
Paradyne 5216 - page 20
20 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty , sales, service, repair , installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the fol ...
Haben Sie eine Frage bezüglich Paradyne 5216?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Paradyne 5216 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Paradyne 5216 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.