Deutsch dropdown-ico

Bedienungsanleitung Toshiba A10

464 Seiten 14.01 mb
Download

Zur Seite of 464

Summary
  • Toshiba A10 - page 1

    [CONFIDENTIAL] Toshiba Personal Computer Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual First edition July 2008 TOSHIBA CORPORATION File Number 960-684 ...

  • Toshiba A10 - page 2

    ii [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Copyright © 2008 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contain ...

  • Toshiba A10 - page 3

    Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite Pro S300, TECRA A10/S10/P10 The procedures described in this manual are intended to help service technicians isolate faulty Field Rep ...

  • Toshiba A10 - page 4

    iv [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Pro S300, TECRA A10/S10/P10 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diag ...

  • Toshiba A10 - page 5

    Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For e ...

  • Toshiba A10 - page 6

    vi [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ... 1-1 1.2 System Unit Block Diagram .................................................... ...

  • Toshiba A10 - page 7

    Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] vii Chapter 2 Troubleshooting Procedures 2.1 Troubleshooting ......................................................................................................... 2- 1 2.2 Troubleshooting Flowchart ................................................................. ...

  • Toshiba A10 - page 8

    viii [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ..................................................................... ...

  • Toshiba A10 - page 9

    Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] ix 3.31 SETUP ..................................................................................................................... 3-79 Chapter 4 Replacement Procedures 4.1 Overview .................................................................................... ...

  • Toshiba A10 - page 10

    x [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 4.30 Smart card unit ......................................................................................................... 4 -87 4.31 LCD unit/FL inverter ............................................................................................... 4-89 4.32 C ...

  • Toshiba A10 - page 11

    [CONFIDENTIAL] Chapter 1 Hardware Overview ...

  • Toshiba A10 - page 12

    1 Hardware Overview 1-ii [CONFIDENTIAL] Satellite Pro S300, TECRA A9(S5/P5/S200) Maintenance Manual (960-684) ...

  • Toshiba A10 - page 13

    1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)[ CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features................................................................................................................... ....1-1 1.2 System Unit Block Diagram ......................................................... ...

  • Toshiba A10 - page 14

    1 Hardware Overview 1-iv [CONFIDENTIAL] Satellite Pro S300, TECRA A9(S5/P5/S200) Maintenance Manual (960-684) Figures Figure 1-1 Front of the computer ....................................................................................1- 7 Figure 1-2 System un it configuration......................................................................... ...

  • Toshiba A10 - page 15

    1.1 Features 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-1 1.1 Features The Toshiba Satellite Pro S300, TECRA A10/S10/P10 Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Sem iconductor (CMOS) technology extensively to provide compact size, min ...

  • Toshiba A10 - page 16

    1 Hardware Overview 1.1 Features 1-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  HDD The computer has a 2.5-inch SATA HDD. The following capacities are available. • • • • 80/120/160/200 / 250 GB  SSD Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive. ...

  • Toshiba A10 - page 17

    1.1 Features 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-3  Batteries The computer has two batteries: a rechargeable Lithium-Ion m ain battery pack and RTC battery (that backs up the Real Time Clock and CMOS mem ory.  Universal Serial Bus (USB2.0) Three USB ports are provided. The p ...

  • Toshiba A10 - page 18

    1 Hardware Overview 1.1 Features 1-4 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  ExpressCard slot(Not used) The internal ExpressCard slot is a Universa l slot. This slot supports ExpressCard/54 and ExpressCard/34 modules.  SmartCard Slot This computer (Some m odels) supports ISO7816-3 asynchronous cards ...

  • Toshiba A10 - page 19

    1.1 Features 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-5  Internal modem The computer contains a MDC, enabling data and fax comm unication. It supports ITU-T V.90 (V.92). The transfer rates are 56 Kbps for data reception, 33.6 Kbps for data transmission, and 14,400 bps for fax transm ...

  • Toshiba A10 - page 20

    1 Hardware Overview 1.1 Features 1-6 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  TOSHIBA Presentation button This button switches the display between internal display, external display, simultaneous display and multi-monitor display.  TOSHIBA Assist button When this button is pressed during power-on, the ...

  • Toshiba A10 - page 21

    1.1 Features 1 Hardware Overview The front of the computer is shown in figure 1-1. Figure 1-1 Front of the computer Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-7 ...

  • Toshiba A10 - page 22

    1 Hardware Overview 1.1 Features The system unit configuration is shown in figure 1-2. Figure 1-2 System unit configuration 1-8 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 23

    1.2 System Unit Block Diagram 1 Hardware Overview 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. Figure 1-3 System unit block diagram Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-9 ...

  • Toshiba A10 - page 24

    1 Hardware Overview 1.2 System Unit Block Diagram 1-10 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) The system unit is composed of the following m ajor components:  Microprocessor The Satellite Pro S300, TECRA A10/S10/P10 computer is equipped with an Intel ® Core TM 2 Duo Processor. These processors incorpor ...

  • Toshiba A10 - page 25

    1.2 System Unit Block Diagram 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-11 • North Bridge (Intel GM45/GL40-Cantiga (G) MCH) Meorom Processor System Bus Supports PCI Express Based Graphics Interface System Memory supports :DDR2-667 ／ DDR2-800, 4GB m ax. DMI(Direct Media Interface: x4 ...

  • Toshiba A10 - page 26

    1 Hardware Overview 1.2 System Unit Block Diagram 1-12 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) -Package 676 pin BGA (31 x 31mm)  Card controller (R5C847) • • • • • - PCI Interface - IEEE1394 Controller - SD/MMC, Memory Stick, xD card Controller  VGA controller The PC comes in with one of the ...

  • Toshiba A10 - page 27

    1.2 System Unit Block Diagram 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-13  Internal LAN Controller • Intel made only GigaBit Ether is used. • This controller has the following functions: – PCI-Ex connection – Controller ： 10/100 PC82562V, Gigabit Intel PC82566MC/MM(AMT) ? ...

  • Toshiba A10 - page 28

    1 Hardware Overview 1.2 System Unit Block Diagram 1-14 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  EC/KBC (Embedded Controller/Keyboard Controller) • One Mitsubishi M306KAFCLPR micon chip functions as both EC and KBC.  PSC (Power Supply Controller) • One TMP86FS49AUG chip is used. • This controller ...

  • Toshiba A10 - page 29

    1.3 3.5-inch Floppy Disk Drive (USB External) 1 Hardware Overview 1.3 3.5-inch Floppy Disk Drive (USB External) The 3.5-inch FDD is a thin, high-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown in figure 1-4. The specifications for the FDD are listed in Table 1-1. Figure 1-4 3.5-inch ...

  • Toshiba A10 - page 30

    1 Hardware Overview 1.4 2.5-inch Hard Disk Drive 1.4 2.5-inch Hard Disk Drive The removable HDD is a random access non-volatile storage device. It has a non-rem ovable 2.5-inch magnetic disk and mini-W inchester type magnetic heads. The computer supports a 80GB, 120GB, 160GB, 200GB or 250GB. The HDD is shown in figure 1-5. Specifications are listed ...

  • Toshiba A10 - page 31

    1.4 2.5-inch Hard Disk Drive 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-17 Table 1-2 2.5-inch HDD specifications Specifications Items HGST G8BC00051 080 HGST G8BC00051 120 HGST G8BC00051 160 HGST G8BC00046 200 HGST G8BC0005 1250 Outline Width (mm) 100.2 ± 0.25 Dimensio ns Height (mm) 9. ...

  • Toshiba A10 - page 32

    1 Hardware Overview 1.5 Optical Drive (ODD) 1-18 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 1.5 Optical Drive (ODD) 1.5.1 DVD-ROM Drive The DVD-ROM drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) DVD-ROM. The specifications of the DVD-ROM are described in Table 1-3. Table 1-3 DVD-ROM drive spec ...

  • Toshiba A10 - page 33

    1.5 Optical Drive (ODD) 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-19 1.5.2 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accomm odates either 12 cm (4.72-inch) or 8 cm (3.15- inch) CD-ROM, DVD-ROM and CD-R/RW. The specifications of the DVD-ROM & CD-R/RW drive are descr ...

  • Toshiba A10 - page 34

    1 Hardware Overview 1.5 Optical Drive (ODD) 1.5.3 DVD-Super Multi Drive The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD-ROM, DVD-ROM, CD-R, CD-RW, DVD-R, DVD+R, DVD-RW, DVD+RW , DVD- RAM, DVD-R DL and DVD+R DL. The specifications are listed in Table 1-5. Figure 1-6 DVD Super Multi drive 1-20 [CONFIDENTIAL] Sat ...

  • Toshiba A10 - page 35

    1.5 Optical Drive (ODD) 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-21 Table 1-5 DVD Super Multi drive outline dimensions Specifications Item TEAC DV-W28S* (G8CC0004712L/120) Width (mm) 128 (excluding projections) Height (mm) 12.7 (excluding projections) Depth (mm) 129.4 (excluding projec ...

  • Toshiba A10 - page 36

    1 Hardware Overview 1.6 Keyboard 1.6 Keyboard The keyboard is mounted 85(US)/87(UK) keys that consist of character key and control key, and in conformity with JIS. The keyboard is connected to mem brane connector on the system board and controlled by the keyboard controller. Figure 1-7 is a view of the keyboard. See Appendix E about a layout of the ...

  • Toshiba A10 - page 37

    1.7 TFT Color Display 1 Hardware Overview 1.7 TFT Color Display The TFT color display consists of 15.4-inch or 14.1-inch WXGA/WXGA+ LCD m odule and FL inverter board. 1.7.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and can display a maximum of 16M colors with 1,280 x 800 or 1,680x1050 resolution. ...

  • Toshiba A10 - page 38

    1 Hardware Overview 1.7 TFT Color Display 1-24 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Table 1-6 LCD module specifications Specifications Item 15.4-inch WXGA TFT LG (G33C0004R110) Number of Dots 1,280 (W) x 800 (H) Dot spacing (mm) 0.25875(H) × 0.25875(V) Display range (mm) 331.2(W) × 207.0(H) Table 1-6 L ...

  • Toshiba A10 - page 39

    1.7 TFT Color Display 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-25 1.7.2 FL Inverter Board The FL inverter board supplies a high frequency current to illuminate the LCD module. Table 1-7 lists the FL inverter board specifications. Table 1-7 FL inverter board specifications Item Specific ...

  • Toshiba A10 - page 40

    1 Hardware Overview 1.8 Power Supply 1-26 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 1.8 Power Supply The power supply supplies many different voltages to the system board and perform s the following functions: 1. Judges that the DC power supply (AC adapter) is connected to the computer. 2. Detects DC output a ...

  • Toshiba A10 - page 41

    1.8 Power Supply 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-27 Table 1-8 Power supply output rating ACPI state S3/S4/S5 S3 S3 S4/S5 S4/S5 G3 M state M1 Moff Moff Moff Moff Wakeup - WOL No WOL WOL No WOL Pow e r line name Voltage [V] Name Object P * PPV × × × × × × CPU * IGD-PGV × ...

  • Toshiba A10 - page 42

    1 Hardware Overview 1.9 Batteries 1-28 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 1.9 Batteries The computer has three types of batteries as follows:  Main battery pack  RTC battery The battery specifications are listed in Table 1-9. Table 1-9 Battery specifications Battery name Material Output voltage C ...

  • Toshiba A10 - page 43

    1.9 Batteries 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-29 1.9.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached t ...

  • Toshiba A10 - page 44

    1 Hardware Overview 1.9 Batteries 1-30 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  Data preservation time When turning off the power in being charged fully, the preservation time is as following Table 1-11. Table 1-11 Data preservation time Condition preservation time Standby About 3 days Battery(4,000 mAh) ...

  • Toshiba A10 - page 45

    1.10 AC Adapter 1 Hardware Overview Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [ CONFIDENTIAL] 1-31 1.10 AC Adapter The AC adapter is also used to charge the battery. Table 1-13 lists the AC adapter specifications. Table 1-13 AC adapter specifications Parameter Specification G71C0006Q210 (2-pin) G71C0006R210 (3-pin) Power 75 ...

  • Toshiba A10 - page 46

    1 Hardware Overview 1.10 AC Adapter 1-32 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 47

    [CONFIDENTIAL] Chapter 2 Troubleshooting Procedures ...

  • Toshiba A10 - page 48

    2 Troubleshooting Procedures 2-ii [CO NFIDENTIAL] Satellite Pro S 300, TECRA A10/S10/P 10 Maintenance Manual (960- 684) 2 ...

  • Toshiba A10 - page 49

    2 Troubleshooting Procedures Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintenance Man ua l (960- 684) [CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ................................................ ...

  • Toshiba A10 - page 50

    2 Troubleshooting Procedures 2-iv [CO NFIDENTIAL] Sat ellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-68 4) 2.9 Display Troubleshooting .......................................................................................... 2-46 Procedure 1 External Monitor Check ....................................................... 2-46 Procedure 2 ...

  • Toshiba A10 - page 51

    2 Troubleshooting Procedures Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintenance Man ua l (960- 684) [CONFIDENTIAL] 2-v 2.18 Fingerprint sensor .................................................................................................... 2-63 Procedure 1 Setting Windows Log-ON password ................................... 2-64 Procedure 2 Re ...

  • Toshiba A10 - page 52

    2 Troubleshooting Procedures 2-vi [CO NFIDENTIAL] Sat ellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-68 4) ...

  • Toshiba A10 - page 53

    2.1 Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-1 2 2.1 Troubleshooting Chapter 2 describes how to determine which Fi eld Replaceable Unit (FRU) in the computer is causing the computer to malfunction. (The “FRU ” m eans the replaceable unit in the field.) ...

  • Toshiba A10 - page 54

    2 Troubleshooting Procedures 2.1 Troubleshooting There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is descri bed in the figure as line. (2) Pin connection is describe d in the figure as arrow. <e.g> Connection of modem 2-2 [CONFIDENTIAL ...

  • Toshiba A10 - page 55

    2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-3 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide fo r determining which troubleshooting procedures to execute. Before going through the flow chart steps, verify the following: ...

  • Toshiba A10 - page 56

    2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (1/2) 2-4 [CONFIDENTIAL ] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Man ual (960-684) ...

  • Toshiba A10 - page 57

    2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-5 ...

  • Toshiba A10 - page 58

    2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-6 [CONFIDENTIAL ] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Man ual (960-684) If the diagnostics program cannot detect an e rror, the problem may be intermittent. The Test program should be executed several tim es to is olate the problem. Check the Log Utilities function to confir ...

  • Toshiba A10 - page 59

    2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-7 15. If a malfunction is detected on the fingerpr int sensor, perform the Fingerprint Sensor Troubleshooting Procedures in Section 2.18. 16. If a malfunction is detected on the Web camerta, perform the ...

  • Toshiba A10 - page 60

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-8 [CONFIDENTIAL ] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Man ual (960-684) 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue wit ...

  • Toshiba A10 - page 61

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-9 Table 2-2 DC IN icon DC IN icon Power supply status Lights blue DC power is being supplie d from the AC adapter. Blinks orange Powe r supply malfunction *1 Doesn’t light Any condition other than ...

  • Toshiba A10 - page 62

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” On for one second “0” On for half second Interval betw ...

  • Toshiba A10 - page 63

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-11 Check 1 Convert the DC IN icon blink pattern into the hexadecimal error code and comp are it to the tables below. Then go to Check 2. Table 2-3 Error code Error code Where error occurs 1*h DC Powe ...

  • Toshiba A10 - page 64

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-12 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684)  Main Battery Error code Meaning 22h Main battery discharge cu rrent is ove r 0.5A. 23h Main battery charge curre nt is over 4.3 A. 24h The compensation value of [0A] is not within the limits fro ...

  • Toshiba A10 - page 65

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-13  E3V output Error code Meaning 60h E3V voltage is over 3.96V. 61h E3V voltage is under 2.81V when the computer is powered on. 62h E3V voltage is under 2.81V when the computer is booting up. 64h ...

  • Toshiba A10 - page 66

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-14 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684)  1R05M-E1V output Error code Meaning A0h 1R05M-E1V voltage is over 1.26V. A1h 1R05M-E1V voltage is under 0.8 9V wh en the computer is powe re d on. A2h 1R05M-E1V voltage is under 0.89V wh en the ...

  • Toshiba A10 - page 67

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-15 Check 2 In the case of error code 10h or 12h:  Make sure the AC adapter and AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If th e cables are connected firmly, go ...

  • Toshiba A10 - page 68

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 3 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the DC IN jack and wall outlet. If these cables are conn ...

  • Toshiba A10 - page 69

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-17 Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble th ...

  • Toshiba A10 - page 70

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-18 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) 2.4 System Board Troubleshooting This section describes how to determ ine if th e system board is malfunctioning or not. Start with Procedure 1 and continue with the other procedures as instructed. ...

  • Toshiba A10 - page 71

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-19 Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes ...

  • Toshiba A10 - page 72

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-20 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Check 3 The IRT checks the system board. When the IRT detects an erro r, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (23) or (24) is displ ...

  • Toshiba A10 - page 73

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Procedure 2 Serial Port Check or Debugging Port Check Check the D port status by a debug port test. The tool for serial port or debug port test is shown below. Serial Port model (W3270 short) Not a Serial Port model Figure 2-2 A set of to ol for debug port test The test procedures are fo ...

  • Toshiba A10 - page 74

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 4. Boot the computer in MS-DOS mode. 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting D port into FDD and input “FD starting drive:>dport”.) The D port status is displayed in the following form; 6. When the D port status is FFFFh ( normal stat ...

  • Toshiba A10 - page 75

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-23 Table 2-4 Debug port error status (1/8) System BIOS Boot block processing CPU setup MCH initializati on ICH initialization EC access check setup of PIT Initialization of ICH and Super I/O CPU MCH( ...

  • Toshiba A10 - page 76

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-24 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Table 2-5 Debug port error status (2/8) System BIOS IRT processing F100 CPU setup CPU IS1050 (CPU Socket) Initialization of ICH, MCH, and Super I/O setup of SD controll er F101 setup of PIT ICH(PCI ...

  • Toshiba A10 - page 77

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-25 Table 2-6 Debug port error status (3/8) EC data reading BIOS processing reading 2 setup of ICH (SATA) setup of ICH (Azalia) Thermal contr ol setup Initialization of KBC Display setup BIOS processi ...

  • Toshiba A10 - page 78

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-26 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Table 2-7 Debug port error status (4/8) F113 Display check ICH(CMOS) IC1600 (ICH) Display setup F114 BIOS Boot logo display ICH(CMOS) VGA IC1200 (VGA) IC5000 (VGA(nVIDA)) IC1600 (ICH) CMOS reading F ...

  • Toshiba A10 - page 79

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-27 Table 2-8 Debug port error status (5/8) F124 LAN setup LAN Controller IC4000 (LAN Controller) setup of ICH (PIC) setup of ICH (DMA C) setting error of ICH (PCI Express) setup of ICH (CMOS) F125 EC ...

  • Toshiba A10 - page 80

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-28 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Table 2-9 Debug port error status (6/8) System BIOS SUSPEND processing F139 Suspension pr ocessing start F13A Preparation before suspension processing EC/KBC(EC) IC3200 (EC/KBC) CPU setup F13B It br ...

  • Toshiba A10 - page 81

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-29 Table 2-10 Debug port error status (7/8) System BIOS RESUME processing F100 Refer to System BIOS IRT processing F101 Refer to System BIOS IRT processing F102 Refer to System BIOS IRT processing F1 ...

  • Toshiba A10 - page 82

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-30 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Table 2-11 Debug port error status (8/8) F131 end of a display setting F132 Password processing EC/KBC(EC) VGA ICH(USB controller) RAM IC3200 (EC/KBC) IC1600 (ICH) CN1400 (RAM Conn .) CN1410 (RAM Co ...

  • Toshiba A10 - page 83

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] 2-31 NOTE: Status outputted by the test means the la st error detected in the debug port test. Check 1 If the D port is status F11Eh or F120h is displayed, go to “HDD Trouble shooting Procedure in Se ...

  • Toshiba A10 - page 84

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-32 [CONFIDENTIAL ] Satellite Pro S30 0, TECRA A10/S10/P10 Maintenance Manual (960- 684) Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more ...

  • Toshiba A10 - page 85

    2.5 USB FDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintena nce Manual (960- 684) [CONFIDENTIAL] 2-33 2.5 USB FDD Troubleshooting To check if the USB FDD is malfunctioning or not, follow the troubl eshooting procedures below as instructed. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Te ...

  • Toshiba A10 - page 86

    2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting 2-34 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, tu rn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation ab ...

  • Toshiba A10 - page 87

    2.5 USB FDD Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board. The connection of the cable and board may be defective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform th ...

  • Toshiba A10 - page 88

    2 Troubleshooting Procedures 2.5 USB FDD Troubleshooting 2-36 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) Check 2 Connect USB FDD to other USB port a nd check if it works properly. If it does not work properly, perform Check 3 Check 3 USB FDD may be fau lty. Replace it with a new one. If the problem still oc ...

  • Toshiba A10 - page 89

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintena nce Manual (960- 684) [CONFIDENTIAL] 2-37 2.6 2.5” HDD Troubleshooting To check if the 2.5” HDD is malfunctioning or not, follow the troubl eshooting procedures below as instructed. Procedure 1: Partition Check Procedure 2: Message Chec ...

  • Toshiba A10 - page 90

    2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting 2-38 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed ...

  • Toshiba A10 - page 91

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintena nce Manual (960- 684) [CONFIDENTIAL] 2-39 Procedure 3 Format Check The computer’s HDD is formatted using the DOS FORMAT program or the physical format program of the test program. To format the HDD, start with Check 1 below and perform th ...

  • Toshiba A10 - page 92

    2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting 2-40 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Dia ...

  • Toshiba A10 - page 93

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check The SATA HDD may be disconnected, or the SA TA HDD, HDD cable or system board may be damaged. Disassemble the com puter fo llowing the steps describ ed in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure ...

  • Toshiba A10 - page 94

    2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting 2-42 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) 2.7 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Ch ...

  • Toshiba A10 - page 95

    2.7 Keyboard Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure keyboard cab ...

  • Toshiba A10 - page 96

    2 Troubleshooting Procedures 2.8 Touch pad Troubleshooting 2-44 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Manual ( 960- 684) 2.8 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution ...

  • Toshiba A10 - page 97

    2.8 Touch pad Troubleshooting 2 Troubleshooting Procedures Procedure 2 Connector Check and Replacement Check The connection of the cable and board may be defective. Otherwise, they m ay be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the cab ...

  • Toshiba A10 - page 98

    2 Troubleshooting Procedures 2.9 Display Troubleshooting 2-46 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) 2.9 Display Troubleshooting To check if the computer’s display is ma lfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diag ...

  • Toshiba A10 - page 99

    2.9 Display Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD/FL cable. FL inverter board is also connected to system board by an LCD/FL cable. In addition, fluorescent lamp is connected to FL inverter board by HV cable. Their cables may be disconnected from system b ...

  • Toshiba A10 - page 100

    2 Troubleshooting Procedures 2.9 Display Troubleshooting 2-48 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) Procedure 4 Replacement Check Fluorescent lamp, FL inverter, LCD module, HV cable and LCD/FL cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement ...

  • Toshiba A10 - page 101

    2.10 Optical Disk Drive Troubleshootin g 2 Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioni ng or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnos ...

  • Toshiba A10 - page 102

    2 Troubleshooting Procedures 2.10 Op tical Disk Drive Troubleshooting 2-50 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) Check 2 The SATA ODD may be damaged. Re place it with a new one following the instructions in Chapter 4, Replacement Procedures and check the operation. If the problem still exists, perform C ...

  • Toshiba A10 - page 103

    2.11 Modem Troubleshooting 2 Troubleshooting Procedures 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, fo llow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execut ...

  • Toshiba A10 - page 104

    2 Troubleshooting Procedures 2.11 Modem Troubleshooting 2-52 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) Check 2 Modem cable or MDC cable m ay be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Chapter ...

  • Toshiba A10 - page 105

    2.12 LAN Troubleshooting 2 Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunc tioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution C ...

  • Toshiba A10 - page 106

    2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting 2-54 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) 2.13 Wireless LAN Troubleshooting To check if the computer’s Wireless LAN is m alfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving ...

  • Toshiba A10 - page 107

    2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sur ...

  • Toshiba A10 - page 108

    2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting 2-56 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disa ssemble the computer ...

  • Toshiba A10 - page 109

    2.14 Bluetooth Troubleshooting 2 Troubleshooting Procedures 2.14 Bluetooth Troubleshooting To check if the Bluetooth is malfunctioning or not, follow the troubl eshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connection Check and Replacement Check Procedure 1 Diagnostic Test Program Execu ...

  • Toshiba A10 - page 110

    2 Troubleshooting Procedures 2.14 Bluetooth Troubleshooting 2-58 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Mainte na nce Manual (960-684) Check 2 The Bluetooth module may be damage d. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures and check the operation. If the problem still exists, perform Che ...

  • Toshiba A10 - page 111

    2.15 Sound Troubleshooting 2 Troubleshooting Procedures 2.15 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program E ...

  • Toshiba A10 - page 112

    2 Troubleshooting Procedures 2.15 Sound Troubleshooting 2-60 [CONFIDENTIAL] Sat ell ite Pro S30 0, TECRA A10/ S1 0/P 10 Maintenance Man ual (960-684) Procedure 3 Replacement Check  If headphone does not work properly, perform check 1.  If external microphone does not wo rk properly, perform check 2.  If internal microphone does not work pr ...

  • Toshiba A10 - page 113

    2.16 Bridge media Slot Troubleshooti ng 2 Troubleshooting Procedures 2.16 Bridge media Slot Troubleshooting This section describes how to determine if the computer's Bridge m edia functions are functioning properly. Perform the steps below star ting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Check on Wi ...

  • Toshiba A10 - page 114

    2 Troubleshooting Procedures 2.17 PC I ExpressCard Slot Troubleshooting 2-62 [CONFIDENTIAL] Sat ell ite Pro S30 0, TECRA A10/ S1 0/P 10 Maintenance Man ual (960-684) 2.17 PCI ExpressCard Slot Troubleshooting This section describes how to check PCI Expr essCard slot by inspecting a card with PCI Express interface and a card with USB 2.0 interface. 1 ...

  • Toshiba A10 - page 115

    2.18 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures 2.18 Fingerprint sensor Troubleshooting CAUTION : To delete the account for confirming the fingerprint operation, it is necessary to log on by the account with the ma nagement authority. If the password has been set to log on, ask the Log-ON password to the user. To check if the ...

  • Toshiba A10 - page 116

    2 Troubleshooting Procedures 2.18 Fi ngerprint sensor Troubleshooting 2-64 [CONFIDENTIAL] Sat ell ite Pro S30 0, TECRA A10/ S1 0/P 10 Maintenance Man ual (960-684) Procedure 1 Setting Windows Log-ON password 1. Open [User Account] from [Control Panel]. 2. Click [User Account]. 3. Click the icon of the account (user’s na me) that you want to set t ...

  • Toshiba A10 - page 117

    2.18 Fingerprint sensor Troubleshootin g 2 Troubleshooting Procedures 7. When the Store to Sensor screen is displa yed, check Store fingerpri nt to Sensor. Click Finish to complete fingerprint registration. Procedure 3 Authentication of fingerprint 1. Turn on the computer to start up Windows. 2. In the Windows logon window, put lightly the first jo ...

  • Toshiba A10 - page 118

    2 Troubleshooting Procedures 2.18 Fi ngerprint sensor Troubleshooting Procedure 4 Connector Check and Replacement Check The connection of the cable and board may be defective. Otherwise, they m ay be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make s ...

  • Toshiba A10 - page 119

    2.19 Web camera Troubleshooting 2 Troubleshooting Procedures 2.19 Web camera Troubleshooting To check if the computer’s web camera is ma lfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows OS Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Windows OS Use the softwar ...

  • Toshiba A10 - page 120

    2 Troubleshooting Procedures 2.19 Web camera Troubleshooting Check 2 If web camera does not work prope rly(the image from a web cam era cannot be displayed. ), web camera m ay be faulty. Replace it with a new one following the steps in Chapter 4, Replacement Procedures . If the problem still occurs, perform Check 3 Check 3 System board may be fault ...

  • Toshiba A10 - page 121

    2.20 Intel Turbo Memory Troubleshooting 2 Troubleshooting Procedures 2.20 Intel Turbo Memory Troubleshooting To check if Intel Turbo Memory is malf unctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows OS Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Windows OS Use the ...

  • Toshiba A10 - page 122

    2 Troubleshooting Procedures 2.20 Intel Turbo Memory Troubleshooting If any problems are found, perform the Procedure 2. Procedure 2 Connector Check and Replacement Check The connection of Intel Turbo Memory card may be faulty or the card may be defective. Disassemble the computer following the step s described in Chapter 4 and perform the followin ...

  • Toshiba A10 - page 123

    [CONFIDENTIAL] Chapter 3 Tests and Diagnostics ...

  • Toshiba A10 - page 124

    3 Tests and Diagnostics 3-ii [CONFIDENTIAL] Satellite Pro S300, TECRA A10/ S1 0/P 10 Maintenance Man ua l (960- 684) 3 ...

  • Toshiba A10 - page 125

    3 Tests and Diagnostics Satellite Pro S 300, TECRA A10/S10/P 10 Maintenance Manual (960- 684) [CONFIDENTIAL ] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................ ...

  • Toshiba A10 - page 126

    3 Tests and Diagnostics 3-iv [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S1 0/P 10 Maintenance Manua l ( 960- 684) 3.20 ONLY ONE TEST ................................................................................................... 3-40 3.21.1 Program Description .......................................................................... 3-40 3.2 ...

  • Toshiba A10 - page 127

    3 Tests and Diagnostics Satellite Pro S 300, TECRA A10/S10/P 10 Maintenance Manual (960- 684) [CO NFIDENTIAL] 3-v Tables Table 3-1 Subtest names .................................................................................................... 3-11 Table 3-2 Error codes and error status names ...................................................... ...

  • Toshiba A10 - page 128

    3 Tests and Diagnostics 3-vi [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S1 0/P 10 Maintenance Manua l ( 960- 684) ...

  • Toshiba A10 - page 129

    3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. The ...

  • Toshiba A10 - page 130

    3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)  REAL TIMER TEST  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST  ERROR RETRY COUNT SET [FDD & HDD] Other tests are:  Wireless LAN TEST (Wireless LAN TEST disk)  LAN/Modem/Bluetooth/IEEE1394 T ...

  • Toshiba A10 - page 131

    3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-3  The Diagnostics Disk (Main T&D) 3.1.3 Heatrun test program The heatrun test starts automatically after the selection. You will need the following equipment to perform this program.  The Diagnostics Disk ...

  • Toshiba A10 - page 132

    3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3.2 Executing the Diagnostic Test To start the Repair test program, follow these steps: 1. Insert the Repair test program disk in the USB floppy disk drive or Optical disk drive. 2. Turn on the computer while pressing U key. The following menu appears. NOTE : The following menu is an example ...

  • Toshiba A10 - page 133

    3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2.1 Diagnostics menu (T&D) Set the highlight bar to 3 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 – ONLY ONE TEST 3 - 4 - HEAD C ...

  • Toshiba A10 - page 134

    3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST 3 - KEYBOARD TEST 4 - DISPLAY TEST 5 - FLOPPY DISK ...

  • Toshiba A10 - page 135

    3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Select the option you want to execute and press Enter . When you select 1- SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT: XXXXX WRITE DATA : X ...

  • Toshiba A10 - page 136

    3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-8 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Use the up and down arrow keys to move the cursor to “ ERROR STOP ”. Use the right and left arrow keys to move the cursor to the desired option and press Enter . Selecting YES of ERROR STOP stops the te ...

  • Toshiba A10 - page 137

    3.3 Setting of the hardware configuration 3 Tests and Diagnostics 3.3 Setting of the hardware configuration To execute this program, input 1 in the startup menu. Then press Enter to select the (2)- Initial config set . The H/W initial inform ation setting tool consists of four subtests. Input the number you want to execute and press Enter . NOTE : ...

  • Toshiba A10 - page 138

    3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-10 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 7. “Create DMIINFO TXT (Y/N)?” is displayed. Press Y, then the DMI information (text data) is written to the Floppy disk, etc. Setting of the HWSC Setting of the UUID Display of the DMI informa ...

  • Toshiba A10 - page 139

    3.4 Heatrun Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-11 3.4 Heatrun Test To execute this program, press 2 , Repair Heatrun and press Enter in the startup menu, press Enter . After selecting this test, the same subtests as 3.23 RUNNING TEST is executed successively. For more d ...

  • Toshiba A10 - page 140

    3 Tests and Diagnostics 3.5 Subtest Names 3-12 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF G ...

  • Toshiba A10 - page 141

    3.5 Subtest Names 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-13 Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER [Not supported] 01 02 03 Ripple pattern Function Wraparound 7 ASYNC [Not supported] 01 02 03 FIR/SIR Point to point (send) FIR/SIR Point to ...

  • Toshiba A10 - page 142

    3 Tests and Diagnostics 3.6 System Test 3-14 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.6 System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ...

  • Toshiba A10 - page 143

    3.6 System Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-15 If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. If the CPU does not support Gerserville (SpeedStep), the following message is displayed and the test is e ...

  • Toshiba A10 - page 144

    3 Tests and Diagnostics 3.7 Memory Test 3-16 [CONFIDENTIAL] Satellite Pro S300, TE CRA A10/S10/P10 Maintenance Manual (960-684) 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 0 ...

  • Toshiba A10 - page 145

    3.8 Keyboard Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-17 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Su ...

  • Toshiba A10 - page 146

    3 Tests and Diagnostics 3.9 Display Test 3.9 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAAAh and 5555h) to ...

  • Toshiba A10 - page 147

    3.9 Display Test 3 Tests and Diagnostics Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mode 117 1024*768 64K] [Mode 118 1024*768 16M] The dis ...

  • Toshiba A10 - page 148

    3 Tests and Diagnostics 3.9 Display Test 3-20 [CONFIDENTIAL] Satellite Pro S300, TE CRA A10/S10/P10 Maintenance Manual (960-684) Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHH ...

  • Toshiba A10 - page 149

    3.10 Floppy Disk Test 3 Tests and Diagnostics 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Enter and ...

  • Toshiba A10 - page 150

    3 Tests and Diagnostics 3.10 Floppy Disk Test 3-22 [CONFIDENTIAL] Satellite Pro S300, TE CRA A10/S10/P10 Maintenance Manual (960-684) Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test en ...

  • Toshiba A10 - page 151

    3.11 Printer Test 3 Tests and Diagnostics 3.11 Printer Test CAUTION : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wrapar ...

  • Toshiba A10 - page 152

    3 Tests and Diagnostics 3.11 Printer Test Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE : To execute thi ...

  • Toshiba A10 - page 153

    3.12 Async Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-25 3.12 Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute and press Enter . ...

  • Toshiba A10 - page 154

    3 Tests and Diagnostics 3.13 Hard Disk Test 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or 09 is executed. Before running the test, the customer should transfer ...

  • Toshiba A10 - page 155

    3.13 Hard Disk Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-27 4. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter . The following message will appear during each subtest. HA ...

  • Toshiba A10 - page 156

    3 Tests and Diagnostics 3.13 Hard Disk Test 3-28 [CONFIDENTIAL] Satellite Pro S300, TE CRA A10/S10/P10 Maintenance Manual (960-684) Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder. (Test the data interference in the ...

  • Toshiba A10 - page 157

    3.14 Real Timer Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-29 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press En ...

  • Toshiba A10 - page 158

    3 Tests and Diagnostics 3.14 Real Timer Test 3-30 [CONFIDENTIAL] Satellite Pro S300, TE CRA A10/S10/P10 Maintenance Manual (960-684) Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, m aking sure the date and time are displayed in the followi ...

  • Toshiba A10 - page 159

    3.15 NDP Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-31 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. CAUTION: Judge the existence of high-speed operation processor by 1bit of the composition ...

  • Toshiba A10 - page 160

    3 Tests and Diagnostics 3.16 Expansion Test 3-32 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound [It is not supported] CAUTION : PCMCIA wrapa ...

  • Toshiba A10 - page 161

    3.16 Expansion Test 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-33 Subtest 02 RGB monitor ID NOTE: To execute this subtest, monitor supporting EDID (Extended Display Identification Data) is required. Connect a wraparound connector to CRT monitor for the test of ID acquisition. This s ...

  • Toshiba A10 - page 162

    3 Tests and Diagnostics 3.17 CD-ROM/DVD-ROM Test 3-34 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.17 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-R ...

  • Toshiba A10 - page 163

    3.18 Error Code and Error Status Names 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-35 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error ...

  • Toshiba A10 - page 164

    3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-36 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE ...

  • Toshiba A10 - page 165

    3.18 Error Code and Error Status Names 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-37 Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD ...

  • Toshiba A10 - page 166

    3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status 3-38 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on t ...

  • Toshiba A10 - page 167

    3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-39 Tables 3-4 HDC Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectab ...

  • Toshiba A10 - page 168

    3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-40 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. # ...

  • Toshiba A10 - page 169

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 01 Pressed Key Display (Main key) When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function that causes th ...

  • Toshiba A10 - page 170

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 02 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch. When moving your finger on the touch pad towards the upper left, the <POINTING> disp ...

  • Toshiba A10 - page 171

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-43 Subtest 03 Wireless communication Switch This subtest checks if the Wireless comm unication switch works properly. If the test is started with the switch ON, following message appears in the display. Wireless communica ...

  • Toshiba A10 - page 172

    3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-44 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) NG m essage appears in the display if a defective is found during the test. Confirm the connection of cable, then execute the test again. Press 9 and return to ONLY ONE TESST menu. Subtest 05 LED This subtest checks if e ...

  • Toshiba A10 - page 173

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 06 Button This subtest checks the m oving of the of the front operation panel button. Press the Toshiba Assist button after the following message appears. Step 1 X 1 2 * * *. Press Function button (Assist button ) OK m essage appears in the display if the test ends without an error. Press any key r ...

  • Toshiba A10 - page 174

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 7 Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2. The vertical wall or plane is necessary. 3. Prevent the machine from shake ...

  • Toshiba A10 - page 175

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-47 When this subtest is selected, the following message appears in the display. The heaven surface establishes in the upper direction Press [Enter] key NOTE : Be sure to execute the test with the display panel opened. Set ...

  • Toshiba A10 - page 176

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Rev B Subtest 8 Docker Dock/Undock This subtest is executed with an Slim Port Replicator II. installed. Press Enter while pushing the eject button of the Slim Port Replicator II. the following message appears. Pushing Eject-SW, and press [Enter] Key Press Enter without pushing the eject button of the Slim ...

  • Toshiba A10 - page 177

    3.21 Head Cleaning 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-49 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operatio ...

  • Toshiba A10 - page 178

    3 Tests and Diagnostics 3.22 Log Utilities 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer. NOTE : Connect USB FDD, when you perform the DIAGNOSTIC PROGRAM from the DV ...

  • Toshiba A10 - page 179

    3.22 Log Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, logs error information into RAM or onto a floppy disk. The error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECT ...

  • Toshiba A10 - page 180

    3 Tests and Diagnostics 3.23 Running Test 3-52 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ) 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02) 3. Display test (subtest 01) 4. Real timer ...

  • Toshiba A10 - page 181

    3.24 Floppy Disk Drive Utilities 2 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-53 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is onl ...

  • Toshiba A10 - page 182

    3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-54 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. ...

  • Toshiba A10 - page 183

    3.24 Floppy Disk Drive Utilities 2 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-55 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage ...

  • Toshiba A10 - page 184

    3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-56 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684)) 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is select ...

  • Toshiba A10 - page 185

    3.24 Floppy Disk Drive Utilities 2 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-57 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another ...

  • Toshiba A10 - page 186

    3 Tests and Diagnostics 3.25 System Configuration 3-58 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.25 System Configuration 3.25.1 Function Description The System Configuration program contains th e following configuration information for the computer: 1. Processor Type [Code/L2 cache] 2. Chip set [VRAM] 3. BI ...

  • Toshiba A10 - page 187

    3.25 System Configuration 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-59 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display: Ver X.XX [Machine Name???] * - Processor Type = ...

  • Toshiba A10 - page 188

    3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3.26 Wireless LAN Test Program (Atheros) Since there is no test program for Atheros-made wireless LAN cards, check the wireless LAN card type of the computer and the antenna connection by using Windows program s. Check of the wireless LAN card type 1. Slide the wireless communication ...

  • Toshiba A10 - page 189

    3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics Check of the antenna connection 1. Confirm that the icon for wireless LAN appears at the lower right of the screen under the circumstances the wireless LAN comm unication is available. (It is no problem if a cross is shown on the icon.) 2. Double-click the icon. If the computer finds ...

  • Toshiba A10 - page 190

    3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) 3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) For the test of Intel-made wireless LAN cards , configure the test environm ent as shown below with the following equipment. ・ AP （ which can operate on W indows XP and is corr ...

  • Toshiba A10 - page 191

    3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) 3 Tests and Diagnostics Open “My Computer” window and click “My Network places” on the left column. Click “View network connections” on the left column. Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-63 • The “Network Conn ...

  • Toshiba A10 - page 192

    3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) Click “Install…” button on the “Local Area Connection Properties” window. • Local Area Connection Properties window Select “Protocol” on the “Select Network Component Type” window and click “Add…” button. 3-64 [CONFIDENTIAL] Sa ...

  • Toshiba A10 - page 193

    3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) 3 Tests and Diagnostics When “Install From Disk” window appears, click “Browse…” and specify the created “Clx_Res” folder. Then Click “OK”. (For the test, “PACKET.INF” file is used.) • Install From Disk window The “Select Network Protocol” window ap ...

  • Toshiba A10 - page 194

    3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g/n Setting up of REF PC) After the completion of REF PC setup, restart the WINDOW S. Then perform the Responder test program for Windows (W TWINSVR.EXE) in the Clx_Res folder. ・ WTWINSVR.EXE Function : Transmitting/receiving of data to/from DUT via AP OS available : W indows ...

  • Toshiba A10 - page 195

    3.28 Wireless LAN Test Program on DUT PC ( Intel-made) 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-67 3.28 Wireless LAN Test Program on DUT PC (Intel-made) 3.28.1 Wireless LAN Test Program (Intel-made : Shirley Peak) on DUT PC This section describes how to perform the wireless LAN tr ...

  • Toshiba A10 - page 196

    3 Tests and Diagnostics 3.28 Wireless LAN Test Program on DUT PC ( Intel-made) 3-68 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) To execute the subtest, input the subtest number and press Enter . Subtest01 Communication test of 11a mode for 5100/5150 module (Two antenna type) This subtest execute transmitting/re ...

  • Toshiba A10 - page 197

    3.28 Wireless LAN Test Program on DUT PC ( Intel-made) 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-69 Subtest03 Communication test of 11g mode for 5100/5150 module (Two antenna type) This subtest execute transmitting/receiving test in 802.11g mode using the main antenna. If a defecti ...

  • Toshiba A10 - page 198

    3 Tests and Diagnostics 3.28 Wireless LAN Test Program on DUT PC ( Intel-made) 3-70 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Subtest06 Communication test of 11b mode for 5100/5150 module (Three antenna type) This subtest execute transmitting/receiving test in 802.11b mode using the main antenna. If a defecti ...

  • Toshiba A10 - page 199

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-71 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/ ...

  • Toshiba A10 - page 200

    3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program Subtest01 (i82562 + ICHx) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error count = 00000 LOOPBACK TEST 100Mbps Auto-negotiation TxRx Tes ...

  • Toshiba A10 - page 201

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear: Testing adaptor...hit <ESC> to abort. * External Loopback Test...PASSED Testing completed. * * Loopb ...

  • Toshiba A10 - page 202

    3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-74 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Denki Seisak ...

  • Toshiba A10 - page 203

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3.29.3 Bluetooth test Preparation ・ For the test of Bluetooth function, use the Windows program installed on the target computer (computer to be tested). A responder device (device for transm itting/receiving data) is also needed. (A mobile phone with the Bluetooth function is ...

  • Toshiba A10 - page 204

    3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 5. Select “Diagnostics” tab and click “Run”. 6. Check the “Log” to confirm the test result. BT address of test computer BT address of responder device 7. When the BT (Bluetooth) address of the responder device appears, the Bluetooth card and antenna connection are OK ...

  • Toshiba A10 - page 205

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-77 3.29.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. ...

  • Toshiba A10 - page 206

    3 Tests and Diagnostic 3.29 Sound Test program Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-78 3.29 Sound Test program Sound TEST disk cannot be used in Satellite Pro S300, TECRA A10/S10/P10. Therefore, please test the sound on Windows OS. 1) Play a music file. 2) click TOSHIBA-> utility -> "PC di ...

  • Toshiba A10 - page 207

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-79 3.31 SETUP 3.31.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory 2. System Date/Time 4. Password (a) User Password (b) Supervisor Password 3. HDD Password (a) HDD (b ...

  • Toshiba A10 - page 208

    3 Tests and Diagnostics 3.31 SETUP 3-80 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) 10. Drives I/O (a) Built-in HDD (b) ODD (c) SATA Controller Mode 11. PCI Bus 12. Display (a) LCD Display Stretch 13. Peripheral (a) Internal Pointing Device 14. Legacy Em ulation (a) USB KB/Mouse Legacy Emulation (b) USB-FDD Leg ...

  • Toshiba A10 - page 209

    3.31 SETUP 3 Tests and Diagnostics 3.31.2 Accessing the SETUP Program While pressing ESC , turn on the power. Then press F1 . The following display appears. Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-81 ...

  • Toshiba A10 - page 210

    3 Tests and Diagnostics 3.31 SETUP 3-82 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 211

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-83 Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pag ...

  • Toshiba A10 - page 212

    3 Tests and Diagnostics 3.31 SETUP 3-84 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) SETUP Options The SETUP screen is divided into 14 functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. This field displays the total a ...

  • Toshiba A10 - page 213

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-85 (b) HDD Password Mode This item registers HDD password and can be selected only for registering HDD password. To change HDD Password Mode when HDD password is registered, delete the registered HDD pa ssword first, and then reg ...

  • Toshiba A10 - page 214

    3 Tests and Diagnostics 3.31 SETUP 3-86 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) NOTE : CD-ROM refers to a DVD-ROM&CD-R/RW drive or DVD Super Multi drive. (b) HDD Priority Use this option to set the booting priority from HDD or USB. Built-in HDD → USB (Default) USB → Built-in HDD 5. Others Whether or ...

  • Toshiba A10 - page 215

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-87 (c) Execute-Disable Bit Capability This option set the Execute-Disable Bit function of CPU to the operation system. Execute-Disable Bit gives higher security function preventing the PC from the computer viruses and buffer over ...

  • Toshiba A10 - page 216

    3 Tests and Diagnostics 3.31 SETUP (f) Auto Power On Use this option to set a time and date for automatic power on and enable or disable the ring indicator feature. Alarm Date Option appears only when Alarm Time is enabled. Set the parameters for the Auto Power On (automatic power on) function and the Wake-up on LAN in the “OPTIONS” window. To ...

  • Toshiba A10 - page 217

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-89 Critical Battery Wake-up Configures what action is taken when the remaining battery power is close to running out while the system is in Sleep Mode. This setting is only available when the Critical battery action in Windows is ...

  • Toshiba A10 - page 218

    3 Tests and Diagnostics 3.31 SETUP 6. Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Initializes devices, which is needed to load an operating system. Operating system initializes other devices. (Default) NOTE: 1. When using installed OS, selecting “Setup by OS” is recommended. 2. ...

  • Toshiba A10 - page 219

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-91 Battery Save Options Processing Speed This feature changes the CPU processing speed. High CPU operates at high speed. (Default in Full Power Mode) Low CPU operates at low speed. (Default in Low Power Mode) CPU Sleep Mode Use t ...

  • Toshiba A10 - page 220

    3 Tests and Diagnostics 3.31 SETUP 3-92 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) (b) PCI Express Link ASPM This option set the power-saving function of PCI Express on the following conditions. A u t o PCI Express devices are not used while battery operation. (Default) D i s a b l e d Disable the Power-saving ...

  • Toshiba A10 - page 221

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-93 9. Drives I/O This option displays the address and interrupts level for hard disk drive and optical disk drive. It is for information only and cannot be changed. (a) Built-in HDD This item displays the Serial ATA Port Number. ...

  • Toshiba A10 - page 222

    3 Tests and Diagnostics 3.31 SETUP 3-94 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) LCD+AnalogRGB Selects both the internal LCD and the external monitor for simultaneous display. NOTE : Pressing Fn+F5 changes the display setting in the order of internal LCD to simultaneous to external monitor. 12. Peripheral Us ...

  • Toshiba A10 - page 223

    3.31 SETUP 3 Tests and Diagnostics Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] 3-95 (c) USB Memory BIOS Support Type A setup about the USB flash memory used for a startup of a com puter. HDD The priority as HDD turns into ranking of HDD in "BootPriority" in a USB flash memory. The priority with othe ...

  • Toshiba A10 - page 224

    3 Tests and Diagnostics 3.31 SETUP 3-96 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 225

    Chapter 4 Replacement Procedures [CONFIDENTIAL] ...

  • Toshiba A10 - page 226

    4 Replacement Procedures 4-ii [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 227

    4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-iii Chapter 4 Contents 4.1 Overview ................................................................................................................... .4 - 1 4.2 Battery pack ................................................................... ...

  • Toshiba A10 - page 228

    4 Replacement Procedures 4-iv [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) 4.27 Battery lock .............................................................................................................. 4-78 4.28 Touch pad/Fingerprint sensor board ................................................................. ...

  • Toshiba A10 - page 229

    4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-v Figures Figure 4-1 Removing the battery pack .......................................................................... 4-11 Figure 4-2 Removing the SIM card (1) ........................................................................ 4-13 F ...

  • Toshiba A10 - page 230

    4 Replacement Procedures 4-vi [CONFIDENTIAL] TEC RA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) Figure 4-31 Removing the MDC modem ........................................................................ 4-51 Figure 4-32 Removing the USB board ............................................................................ 4-52 Figure 4- ...

  • Toshiba A10 - page 231

    4 Replacement Procedures TECRA A10/S10/P10/Sate llitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-vii Figure 4-63 Removing the harness holder L ................................................................. 4-103 Figure 4-64 Removing the LCD harness (2) ................................................................. 4-104 Figure 4-65 ...

  • Toshiba A10 - page 232

    4 Replacement Procedures 4-viii [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 233

    4.1 Overview 4 Replacement Procedures 4 Replaceme nt Procedure s 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FR Us must be removed before a particul ...

  • Toshiba A10 - page 234

    4 Replacement Procedures 4.1 Overview 4-2 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Please prepare required parts in advance, when replacing the following items. ITEM Parts List ITEM No PART NAME Quantity 50 COVER ASSY 1 COVER ASSY 64,64-A TOUCH PAD 1 ITEM Parts List ITEM No PART NAME Quantity 51 LCD COVER AS ...

  • Toshiba A10 - page 235

    4.1 Overview 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-3 The main parts in this manual are indicated in the part list by the f ollowing names. Parts List ITEM No Manual NAME PART NAME 01A System board PCB ASSY FG6INx 01B Switch board PCB ASSY FG6SWx 01C USB board PCB ASSY FG6USx 01D S ...

  • Toshiba A10 - page 236

    4 Replacement Procedures 4.1 Overview 4-4 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1) Always use the genuine battery that is authorized ...

  • Toshiba A10 - page 237

    4.1 Overview 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-5 Before You Begin Take note of the following points before starti ng work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for rem oving the battery pack is described in sectio ...

  • Toshiba A10 - page 238

    4 Replacement Procedures 4.1 Overview Disassembly Procedure Four main types of cable connector are used. Pressure plate connector • • • • Spring connector Back flip connector Normal pin connector For pressure plate connectors, slide the pressure plate holding tags on both sides of the plastic pressure plate on the connector and pull the cab ...

  • Toshiba A10 - page 239

    4.1 Overview 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-7 Assembly Procedures After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the comp ...

  • Toshiba A10 - page 240

    4 Replacement Procedures 4.1 Overview Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: Toshiba recommends that you use an electric screw driver fo ...

  • Toshiba A10 - page 241

    4.1 Overview 4 Replacement Procedures Grip Color Some screws have a colored grip area to help you determine the length of the screw. [Normal grip] • Even numbered length screws: Brown • Odd numbered length screws: White Grip area • Special length screw: Blue [Special grip] • Even numbered length screws: Yellow • Odd numbered length screws ...

  • Toshiba A10 - page 242

    4 Replacement Procedures 4.1 Overview 4-10 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Screw Notation To make maintenance of the com puter easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Format: Screw type + Screw length (mm) Screw sh ...

  • Toshiba A10 - page 243

    4.2 Battery pack 4 Replacement Procedures 4.2 Battery pack Removing the Battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack. 1. Turn off the p ...

  • Toshiba A10 - page 244

    4 Replacement Procedures 4.2 Battery pack 4-12 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the Battery pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, operated, handled, or dispos ...

  • Toshiba A10 - page 245

    4.3 SIM card 4 Replacement Procedures 4.3 SIM card Removing the SIM card To remove the SIM card, follow the steps below and refer to Figure 4-2 and 4-3. 1. Slide the SIM card release latch in the direction as shown in the figure below. 2. Turn up the SIM card holder in the direction as shown in the figure below. SIM card release latch SIM card hold ...

  • Toshiba A10 - page 246

    4 Replacement Procedures 4.3 SIM card 3. Remove the SIM card from the SIM card holder. SIM card Figure 4-3 Removing the SIM card (2) Installing the SIM card To install the SIM card, follow the steps below and refer to Figure 4-2 and 4-3. 1. Set the SIM card into the SIM card holder. 2. Lay the SIM card holder down and lock the SIM card release latc ...

  • Toshiba A10 - page 247

    4.4 PC card/Bridge media/Smart card 4 Replacement Procedures 4.4 PC card/Bridge media/Smart card 4.4.1 PC card Removing the PC card To remove the PC card, follow the steps below and refer to Figure 4-4. CAUTION: Insert or remove a PC card in accordance with any instructions in their manual or the manuals of the computer system you are using. 1. Pre ...

  • Toshiba A10 - page 248

    4 Replacement Procedures 4.4 PC card/Bridge media/Smart card 4.4.2 Bridge media (SD Card/Memory St ick/xD Picture Card/MultiMedia card) Removing the Bridge media To remove the Bridge media, follow the steps below and refer to Figure 4-5. CAUTION: Insert or remove a Bridge media in accordance with any instructions in each Bridge Media manual or the ...

  • Toshiba A10 - page 249

    4.4 PC card/Bridge media/Smart card 4 Replacement Procedures 4.4.3 Smart card Removing the Smart card To remove the Smart card, follow the steps below and refer to Figure 4-6. CAUTION: Insert or remove a Smart card in accordance with any instructions in the Smart card manual or the manuals of the computer system you are using. 1. Pull out the Smart ...

  • Toshiba A10 - page 250

    4 Replacement Procedures 4.5 Memory module 4.5 Memory module Removing the Memory module To remove the mem ory module, confirm that the com puter is shut down. Then follow the steps below and refer to Figure 4-7 and 4-8. CAUTION: When removing the memory module, make sure the computer is powered off. Removing a memory module with the power on might ...

  • Toshiba A10 - page 251

    4.5 Memory module 4 Replacement Procedures 4. Open the left and right latches outside and remove the memory module(s) . Memory module Latch Latch Figure 4-8 Removing the memory module TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-19 ...

  • Toshiba A10 - page 252

    4 Replacement Procedures 4.5 Memory module 4-20 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the Memory module To install the memory m odule, confirm that the computer is shut down. Then follow the steps below and refer to Figure 4-7 and 4-8. CAUTION: When installing the memory module, make sure the c ...

  • Toshiba A10 - page 253

    4.6 Fin cover 4 Replacement Procedures 4.6 Fin cover NOTE : When repairing the PC, clean the cooling fin with a vacuum cleaner. Do not use cotton sticks and tweezers to remove dusts. It may cause the cooling module problem or dusts stuffed. Removing the Fin cover To remove the Fin cover, follow the steps below and refer to Figure 4-9. 1. Push down ...

  • Toshiba A10 - page 254

    4 Replacement Procedures 4.7 HDD 4.7 HDD Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-10 and 4-11. CAUTION : Take care not to press on the top or bottom of a HDD. Pressure may cause the data loss or damage to the device. 1. Remove the following screw securing the HDD cover. • M2.5 × 5B FLAT HEAD screw × 1 2. ...

  • Toshiba A10 - page 255

    4.7 HDD 4 Replacement Procedures 4. Remove the following screws and separate the HDD and HDD holder . • M3.0 × 4C FLAT HEAD screw × 4 M3.0 × 4C FLAT HEAD HDD HDD Holder M3.0 × 4C FLAT HEAD M3.0 × 4C FLAT HEAD M3.0 × 4C FLAT HEAD Figure 4-11 Removing the HDD TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-23 ...

  • Toshiba A10 - page 256

    4 Replacement Procedures 4.7 HDD 4-24 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-10 and 4-11. 1. Set the HDD to the HDD Holder and secure them with the following screw s . • M3.0 × 4C FLAT HEAD screw × 4 2. Set the connecto ...

  • Toshiba A10 - page 257

    4.8 Optical disk drive (DVD-ROM/DVD-Super Multi drive) 4 Replacement Procedures 4.8 Optical disk drive (DVD-ROM/DVD-Super Multi drive) Removing the Optical disk drive To remove the optical disk drive, follow the steps below and refer to Figure 4-12 to 4-13. CAUTION: When the optical disk inside the optical disk drive can not be ejected because of s ...

  • Toshiba A10 - page 258

    4 Replacement Procedures 4.8 Optical disk drive (DVD-ROM/DVD-Super Multi drive) 3. Remove the following screws and ODD rear bracket . • M2.0 × 2.7C Unique screw × 2 4. Remove the following screw and ODD side bracket . • M2.0 × 3C S-THIN HEAD screw × 1 M2.0 × 3C S-THIN HEAD ODD side bracket M2.0 × 2.7C Unique ODD rear bracket Optical disk ...

  • Toshiba A10 - page 259

    4.9 Keyboard 4 Replacement Procedures 4.9 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figure 4-14 to 4-17. CAUTION: As the keytop may fall out, when handling the keyboard always hold it by the frame and do not touch the keytop. 1. Turn over the computer. 2. Insert your fingers into the slits and releas ...

  • Toshiba A10 - page 260

    4 Replacement Procedures 4.9 Keyboard 3. Open the display and make it flat. 4. Insert your finger into the slot on left side and remove the KB holder . KB holder Slot Figure 4-15 Removing the KB holder (2) 4-28 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) ...

  • Toshiba A10 - page 261

    4.9 Keyboard 4 Replacement Procedures 5. Remove the following screws securing the keyboard. • M2.5 × 4B FLAT HEAD screw × 2 6. Lift the top edge of the keyboard while releasing the latches and turn the keyboard face down on the palm rest. M2.5 × 4B FLAT HEAD M2.5 × 4B FLAT HEAD Latch Keyboard Latch Latch Figure 4-16 Removing the keyboard (1) ...

  • Toshiba A10 - page 262

    4 Replacement Procedures 4.9 Keyboard 7. Remove the following screw and slide the KB support plate in the direction as shown in the figure below to remove. • M2.5 × 10B FLAT HEAD screw × 1 8. Disconnect the keyboard flexible cable from the connector CN3230 on the system board and remove the keyboard . M2.5 × 10B FLAT HEAD KB support plate Keyb ...

  • Toshiba A10 - page 263

    4.9 Keyboard 4 Replacement Procedures Installing the Keyboard To install the keyboard, follow the steps below and refer to Figure 4-14 to 4-17. 1. Place the keyboard face down on the palm rest and connect the keyboard flexible cable to the connector CN3230 on the system board. 2. Set the KB support plate and slide it. 3. Secure the KB support plate ...

  • Toshiba A10 - page 264

    4 Replacement Procedures 4.10 SW board 4.10 SW board Removing the SW board To remove the SW board, follow the steps below and refer to Figure 4-18 to 4-20. 1. Disconnect the SW board FFC from the connector CN9600 on the SW board. 2. Push down the hook and slide the SW board in the direction as shown in the figure below to remove it. CN9600 SW board ...

  • Toshiba A10 - page 265

    4.10 SW board 4 Replacement Procedures 3. Peel off the insulator (COVER UP INSULATOR). Insulator (COVER UP INSULATOR) Figure 4-19 Removing the insulator (COVER UP INSULATOR) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-33 ...

  • Toshiba A10 - page 266

    4 Replacement Procedures 4.10 SW board 4. Disconnect the SW board FFC from the connector CN9500 on the system board. CN9500 SW board FFC Figure 4-20 Removing the SW board FFC Installing the SW board To install the SW board, follow the steps below and refer to Figure 4-18 to 4-20. 1. Connect the SW board FFC to the connector CN9600 on the SW board. ...

  • Toshiba A10 - page 267

    4.11 SIM board 4 Replacement Procedures 4.11 SIM board Removing the SIM board To remove the SIM board, follow the steps below and refer to Figure 4-21. 1. Disconnect the SIM board FFC from the connector CN9570 on the system board. 2. Remove the SIM board from the slot while peeling the double-sided tapes . 3. Disconnect the SIM board FFC from the c ...

  • Toshiba A10 - page 268

    4 Replacement Procedures 4.11 SIM board Installing the SIM board To install the SIM board, follow the steps below and refer to Figure 4-21. 1. Connect the SIM board FFC to the connector CN9670 on the back of the SIM board. NOTE : In the case of the 15.4-inch model, arrange the SIM board FFC as shown in the figure below. SIM board FFC SIM board 2. S ...

  • Toshiba A10 - page 269

    4.12 Wireless LAN card 4 Replacement Procedures 4.12 Wireless LAN card Removing the Wireless LAN card To remove the wireless LAN card, follow the steps below and refer to Figure 4-22. 1. Disconnect the wireless LAN antenna cables from the wireless LAN card (white cable from Main and black cable from Aux) using an antenna coaxial cable disconnector. ...

  • Toshiba A10 - page 270

    4 Replacement Procedures 4.12 Wireless LAN card 4-38 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the Wireless LAN card To install the wireless LAN card, follow the steps below and refer to Figure 4-22. 1. Insert the wireless LAN card to the connector on the system board slantwise and press it to conn ...

  • Toshiba A10 - page 271

    4.13 3G card 4 Replacement Procedures 4.13 3G card Removing the 3G card To remove the 3G card, follow the steps below and refer to Figure 4-23 1. Disconnect the 3G antenna cables from the 3G card using an antenna coaxial cable disconnector. 2. Remove the following screws securing the 3G card . • M2.0 × 4B BIND screw × 2 3. Disconnect the 3G car ...

  • Toshiba A10 - page 272

    4 Replacement Procedures 4.13 3G card 4-40 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the 3G card To install the 3G card, follow the steps below and refer to Figure 4-23. 1. Insert the 3G card to the connector on the system board slantwise and press it to connect firmly. 2. Push down the 3G card and ...

  • Toshiba A10 - page 273

    4.14 Robson card 4 Replacement Procedures 4.14 Robson card Removing the Robson card To remove the Robson card, follow the steps below and refer to Figure 4-24. 1. Remove the following screws securing the Robson card . • M2.0 × 4B BIND screw × 2 2. Disconnect the Robson card from the connector on the system board. M2.0x4B BIND Robson card Figure ...

  • Toshiba A10 - page 274

    4 Replacement Procedures 4.14 Robson card 4-42 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) Installing the Robson card To install the Robson card, follow the steps below and refer to Figure 4-24. 1. Insert the Robson card to the connector on the system board slantwise and press it to connect firmly. 2. Push down ...

  • Toshiba A10 - page 275

    4.15 Speaker 4 Replacement Procedures 4.15 Speaker Removing the Speaker To remove the speaker, follow the steps below and refer to Figure 4-25 to 4-27. 1. Disconnect the speaker harness from the connector CN6150 on the system board. CN6150 Speaker harness Figure 4-25 Removing the speaker (1) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (9 ...

  • Toshiba A10 - page 276

    4 Replacement Procedures 4.15 Speaker 2. Peel off the three insulators (SQUARE INSULATOR) and turn up the insulators . Insulator (SQUARE INSULATOR) Insulator Figure 4-26 Removing the insulator 4-44 [CONFIDENTIAL] TECRA A10/S10/P 10/SatellitePro S300 Maintenance Manual ( 960-684) ...

  • Toshiba A10 - page 277

    4.15 Speaker 4 Replacement Procedures NOTE: Peel off three insulators (one from left, two from right) in the case of the 15.4-inch model. The figure below shows the location of two insulators on the right. Insulator (right) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-45 ...

  • Toshiba A10 - page 278

    4 Replacement Procedures 4.15 Speaker 3. Remove the speakers (left and right) from the speaker slots while pushing the guides and speaker harness from the slot. Speaker (blue&black harness) Speaker harness Speaker (red&white harness) Guide Guide Figure 4-27 Removing the speaker (2) Installing the Speaker To install the speaker, follow the s ...

  • Toshiba A10 - page 279

    4.16 Cover assembly and Base assembly 4 Replacement Procedures 4 Replacement Procedu es 4.16 Cover assembly and Base assembly r Removing the Cover assembly and Base assembly To remove the cover assembly and base assem bly, follow the steps below and refer to Figure 4-28 to 4-30. 1. Close the display and turn over the computer. 2. Remove the followi ...

  • Toshiba A10 - page 280

    4 Replacement Procedures 4.16 Cover assembly and Base assembly 3. Turn over the computer and open the display. 4. Disconnect the touch pad FFC , Bluetooth harness , camera harness and LCD harness from the connector CN9550 , CN4440 , CN9540 and CN5000 on the system board. 5. Peel off the acetate tape on the Smart card FFC. 6. Disconnect the Smart ca ...

  • Toshiba A10 - page 281

    4.16 Cover assembly and Base assembly 4 Replacement Procedures 8. Separate the cover assembly and base assembly while releasing the latches. Cover assembly Base assembly Figure 4-30 Removing the cover assembly and base assembly (4) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-49 ...

  • Toshiba A10 - page 282

    4 Replacement Procedures 4.16 Cover assembly and Base assembly Installing the Cover assembly and Base assembly To install the cover assembly and base assembly, follow the steps below and refer to Figure 4-28 to 4-30. 1. Place the cover assembly on the base assembly and secure them with the following screws . • M2.5 × 10B FLAT HEAD screw × 4 2. ...

  • Toshiba A10 - page 283

    4.17 MDC modem/USB board 4 Replacement Procedures 4.17 MDC modem/USB board Removing the MDC modem/USB board To remove the MDC modem /USB board, follow the steps below and refer to Figure 4-31 and 4-32. 1. Remove the following screws securing the MDC m odem. • M2.0 × 4B BIND screw × 2 2. Take out the RJ11 harness from the slot and lift the MDC m ...

  • Toshiba A10 - page 284

    4 Replacement Procedures 4.17 MDC modem/USB board 4. Disconnect the USB harness from the connector CN9560 on the system board and connector CN9660 on the USB board. 5. Remove the USB board from the slot of the base assem bly while pushing the latches in the direction as shown in the figure below. USB board USB harness CN9560 CN9660 Latch Figure 4-3 ...

  • Toshiba A10 - page 285

    4.17 MDC modem/USB board 4 Replacement Procedures Installing the MDC modem/USB board To install the MDC modem/USB board, follow the steps below and refer to Figure 4-31 and 4-32. 1. Set the USB board to the slot of the base assembly while engaging the latches . 2. Connect the USB harness to the connector CN9560 on the system board and connector CN9 ...

  • Toshiba A10 - page 286

    4 Replacement Procedures 4.18 RGB harness/RJ45 harness 4.18 RGB harness/RJ45 harness Removing the RGB harness/RJ45 harness To remove the RGB harness/RJ45 harness, follow the steps below and refer to Figure 4-35 and 4-36. 1. Turn up the insulator and disconnect the RGB harness from the connector CN9510 on the system board. 2. Remove the following sc ...

  • Toshiba A10 - page 287

    4.18 RGB harness/RJ45 harness 4 Replacement Procedures 3. Disconnect the RJ45 harness from the connector CN4100 on the system board and remove the RJ45 harness from the slot of the base assem bly. RJ45 harness CN4100 Insulator Figure 4-34 Removing the RJ45 harness TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-55 ...

  • Toshiba A10 - page 288

    4 Replacement Procedures 4.18 RGB harness/RJ45 harness Installing the RGB harness/RJ45 harness To install the RGB harness/RJ45 harness, follow the steps below and refer to Figure 4-35 and 4-36. 1. Turn up the insulator and connect the RJ45 harness to the connector CN4100 on the system board. 2. Set the RJ45 harness into the slot of the base assembl ...

  • Toshiba A10 - page 289

    4.19 Serial board 4 Replacement Procedures 4.19 Serial board Removing the Serial board To remove the serial board, follow the steps below and refer to Figure 4-35. 1. Disconnect the serial board FFC from the connector CN9520 on the system board. 2. Push the hook to release and remove the serial board from the slot of the base assembly. 3. Disconnec ...

  • Toshiba A10 - page 290

    4 Replacement Procedures 4.19 Serial board 4-58 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Installing the Serial board To install the serial board, follow the steps below and refer to Figure 4-35. 1. Connect the serial board FFC to the connector CN9620 on the back of the serial board. 2. Set the serial board in ...

  • Toshiba A10 - page 291

    4.20 Microphone harness 4 Replacement Procedures 4.20 Microphone harness Removing the Microphone harness To remove the microphone harness, follow the steps below and refer to Figure 4-36. 1. Disconnect the microphone harness from the connector CN6050 on the sound board. 2. Remove the microphone harness from the slot of the base assem bly. CN6050 Mi ...

  • Toshiba A10 - page 292

    4 Replacement Procedures 4.21 System board 4-60 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) 4.21 System board CAUTION: When replacing with a new system board, the following procedures must be executed. (1) Before replacing the system board, execute subtest02 “DMI ggg information save” in 3.3 Setting of the h ...

  • Toshiba A10 - page 293

    4.21 System board 4 Replacement Procedures l • M2.5 × 6C Tapping screw × 4 4. Remove the ODD FPC from the connector CN1950 on the back of the system board. (15.4-inch model only) Glass tape M2.5x6C Tapping DC-IN jack CN9530 M2.5x6C Tapping M2.5x6C Tapping CN1950 ODD FPC Sound board FFC Figure 4-37 Removing the system board TECRA A10/S10/P10/Sat ...

  • Toshiba A10 - page 294

    4 Replacement Procedures 4.21 System board 5. Disconnect the DC-IN harness and HDD harness from the connector CN8800 and CN1900 on the back of the system board. CN8800 CN1900 HDD harness DC-IN harness Figure 4-38 Removing the DC-IN harness/HDD harness 4-62 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 295

    4.21 System board 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-63 Installing the System board To install the system board, follow the steps below and refer to Figure 4-37 to 4-38. 1. Connect the DC-IN harness and HDD harness to the connector CN8800 and CN1900 on the back of the system bo ...

  • Toshiba A10 - page 296

    4 Replacement Procedures 4.22 GFX board/GFX fin 4.22 GFX board/GFX fin Removing the GFX board/GFX fin To remove the GFX board/GFX fin, follow the steps below and refer to Figure 4-39 and 4-40. 1. Remove the following screws and disconnect the GFX board (with the GFX fin) from the connector CN5900 on the system board. • M2.0 × 4B BIND screw × 2 ...

  • Toshiba A10 - page 297

    4.22 GFX board/GFX fin 4 Replacement Procedures 2. Remove the following screws and separate the GFX fin and GFX board . • M2.0 × 3C S-THIN HEAD screw × 4 GFX board GFX fin M2.0x3C S-THIN HEAD M2.0x3C S-THIN HEAD Cool sheet Figure 4-40 Removing the GFX board/GFX fin (2) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTI ...

  • Toshiba A10 - page 298

    4 Replacement Procedures 4.22 GFX board/GFX fin 4-66 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Installing the GFX board/GFX fin To install the GFX board/GFX fin, follow the steps below and refer to Figure 4-39 and 4-40. 1. If there is already cool sheet on the GFX board or GFX fin, remove the cool sheet. Stick ...

  • Toshiba A10 - page 299

    4.23 CPU/CPU fin/DC fan 4 Replacement Procedures 4.23 CPU/CPU fin/DC fan Removing the CPU/CPU fin/DC fan To remove the CPU/CPU fin/DC fan, follow the steps below and refer to Figure 4-44 to 4-46. 1. Disconnect the fan harness from the connector CN8771 on the system board. 2. Remove the following screws and heat sink plate . • M2.0 × 4B BIND scre ...

  • Toshiba A10 - page 300

    4 Replacement Procedures 4.23 CPU/CPU fin/DC fan 4. Remove the following screws and separate the DC fan and CPU fin . • M2.5 × 4B FLAT HEAD screw × 2 CPU fin DC fan M2.5x4B FLAT HEAD Cool sheet Figure 4-42 Removing the CPU fin/DC fan (2) 4-68 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 301

    4.23 CPU/CPU fin/DC fan 4 Replacement Procedures 5. Unlock the CPU by turning the cam counterclockwise on the CPU socket by 180 degrees with a flat-blade screwdriver. 6. Remove the CPU . Figure 4-43 Removing the CPU CAUTION: When removing the CPU, lift it up right above. Otherwise, pins of the CPU may be damaged. TECRA A10/S10/P10/SatellitePro S300 ...

  • Toshiba A10 - page 302

    4 Replacement Procedures 4.23 CPU/CPU fin/DC fan Installing the CPU/CPU fin/DC fan To install the CPU/CPU fin/DC fan, follow the steps below and refer to Figure 4-44 to 4-48. 1. Make sure that the cam of the CPU socket is in the unlock (OPEN) position. 2. Set the CPU to the correct position in the CPU socket . Make sure the position of the CPU (tri ...

  • Toshiba A10 - page 303

    4.23 CPU/CPU fin/DC fan 4 Replacement Procedures 4. When silicon grease is already applied to the CPU or CPU fin, wipe them of f with a cloth in advance. 5. Apply new grease (DENKA GFC-F1) on the CPU using a special syringe as shown in the following figure. Apply quarter of scale (0.25ml) of grease evenly on the CPU chip. Grease CPU Figure 4-45 App ...

  • Toshiba A10 - page 304

    4 Replacement Procedures 4.24 PC card unit 4.24 PC card unit Removing the PC card unit To remove the PC card unit, follow the steps below and refer to Figure 4-49. 1. Remove the following screws securing the PC card unit. • M2.0 × 3C Tapping screw × 2 • M2.0 × 8C Tapping screw × 2 2. Remove the PC card unit while releasing the latches . M2. ...

  • Toshiba A10 - page 305

    4.24 PC card unit 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-73 Installing the PC card unit To install the PC card unit, follow the steps below and refer to Figure 4-49. 1. Set the PC card unit while engaging the latches and secure it with the following screws . • M2.0 × 3C Tapping ...

  • Toshiba A10 - page 306

    4 Replacement Procedures 4.25 RTC battery 4.25 RTC battery CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the laws and ordinances of your local authority. Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-50. 1. Peel off the glass tape and ...

  • Toshiba A10 - page 307

    4.25 RTC battery 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-75 Installing the RTC battery To install the RTC battery, follow the steps below and refer to Figure 4-50. 1. Set the RTC battery into the insulator (RTC BATT INSULATOR). 2. Set the insulator (RTC BATT INSULATOR) to the slot. ...

  • Toshiba A10 - page 308

    4 Replacement Procedures 4.26 Sound board 4.26 Sound board Removing the Sound board To remove the sound board follow the steps below and refer to Figure 4-51. 1. Peel off the glass tape . 2. Remove the following screws and sound board from the slot. • M2.5 × 4B FLAT HEAD screw × 2 3. Disconnect the sound board FFC from the connector CN9630 on t ...

  • Toshiba A10 - page 309

    4.26 Sound board 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-77 Installing the Sound board To install the sound board follow the steps below and refer to Figure 4-48. 1. Connect the sound board FFC to the connector CN9630 on the sound board. 2. Set the sound board to the slot and secure ...

  • Toshiba A10 - page 310

    4 Replacement Procedures 4.27 Battery lock 4.27 Battery lock Removing the Battery lock To remove the battery lock, follow the steps below and refer to Figure 4-49. 1. Remove the battery lock button L while pushing latches inside to release them. 2. Turn up the insulator (BATT LOCK L INSULATOR) and remove the battery lock L from the slot. 3. Remove ...

  • Toshiba A10 - page 311

    4.27 Battery lock 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-79 Installing the Battery lock To install the battery lock, follow the steps below and refer to Figure 4-49. 1. Insert the sticks of the battery lock L and battery lock R into the springs . 2. Turn up the insulator (BATT LOCK ...

  • Toshiba A10 - page 312

    4 Replacement Procedures 4.28 Touch pad/Fingerprint sensor board 4 Replaceme nt Procedure s 4.28 Touch pad/Fingerprint sensor board Removing the Touch pad/Fingerprint sensor board To remove the touch pad/fingerprint sensor boa rd, follow the steps below and refer to Figure 4-50 to 4-53. 1. Turn up the insulator (TPAD PLT INSULATOR) and remove the f ...

  • Toshiba A10 - page 313

    4.28 Touch pad/Fingerprint sensor board 4 Replacement Procedures 3. Disconnect the touch pad FFC , touch pad button FFC and dual button FFC from the connector CN9650 and CN3240 on the fingerprint sensor board and connector on the touch pad. NOTE : In models without a dual button, there is no dual button FFC. 4. Remove the unit dual pad (with the fi ...

  • Toshiba A10 - page 314

    4 Replacement Procedures 4.28 Touch pad/Fingerprint sensor board 5. Remove the following screws and separate the fingerprint sensor board and unit dual pad . • M2.0 × 3C S-THIN HEAD screw × 2 Unit dual pad Fingerprint sensor board M2.0x3C S-THIN HEAD Figure 4-52 Removing the touch pad/fingerprint sensor board (3) 4-82 [CONFIDENTIAL] TECRA A10/S ...

  • Toshiba A10 - page 315

    4.28 Touch pad/Fingerprint sensor board 4 Replacement Procedures 6. Disconnect the touch pad button FFC from the connector on the touch pad and peel off the touch pad . NOTE : Do not reuse the removed touch pad. Be sure to use a new touch pad. Touch pad Connector COVER ASSY Touch pad button FFC Figure 4-53 Removing the touch pad/fingerprint sensor ...

  • Toshiba A10 - page 316

    4 Replacement Procedures 4.28 Touch pad/Fingerprint sensor board Installing the Touch pad/Fingerprint sensor board To install the touch pad/fingerprint sensor boa rd, follow the steps below and refer to Figure 4-50 to 4-53. 1. Connect the touch pad button FFC to the connector on a new touch pad and stick the touch pad in place. 2. Set the fingerpri ...

  • Toshiba A10 - page 317

    4.29 Bluetooth module 4 Replacement Procedures 4.29 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below and refer to Figure 4-54. 1. Lift up the hook and slide the Bluetooth holder in the direction in the figure below to remove it from the guides . 2. Remove the Bluetooth module from the guides . Bl ...

  • Toshiba A10 - page 318

    4 Replacement Procedures 4.29 Bluetooth module 4-86 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) 1. Set the Bluetooth module along the guides and arrange the Bluetooth harness under the guides . 2. Set the Bluetooth holder under the guides and slide it until the hook is engaged. ...

  • Toshiba A10 - page 319

    4.30 Smart card unit 4 Replacement Procedures 4.30 Smart card unit Removing the Smart card unit To remove the Smart card unit, follow the steps below and refer to Figure 4-55. 1. Peel off the insulator fixing the Smart card FPC. 2. Pull the Smart card FPC from the hole 1 out, then pull the Smart card FPC from the hole 2 out. 3. Lift up the hook of ...

  • Toshiba A10 - page 320

    4 Replacement Procedures 4.30 Smart card unit 4-88 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Installing the Smart card unit To install the Smart card unit, follow the steps below and refer to Figure 4-55. 1. Pass the Smart card FPC through the hole2 and slide the Smart card unit under the guides until the hook ...

  • Toshiba A10 - page 321

    4.31 LCD unit/FL inverter 4 Replacement Procedures 4.31 LCD unit/FL inverter Removing the LCD unit/FL inverter To remove the LCD unit/FL inverter, follow the steps below and refer to Figure 4-56 to 4-60. 1. Remove the wireless LAN antenna cables and camera harness from the slot. Camera harness Wireless LAN antenna cable (white) Wireless LAN antenna ...

  • Toshiba A10 - page 322

    4 Replacement Procedures 4.31 LCD unit/FL inverter 2. Peel off the LCD mask seals and remove the following screws . • M2.5 × 5B FLAT HEAD screw × 2 3. Separate the LCD cover and cover assembly while releasing the latches. M2.5x5B FLAT HEAD M2.5x5B FLAT HEAD LCD mask seal LCD cover LCD mask seal Slit Figure 4-57 Removing the LCD cover 4-90 [CONF ...

  • Toshiba A10 - page 323

    4.31 LCD unit/FL inverter 4 Replacement Procedures 4. Peel off the glass tape . 5. Disconnect the LCD harness and HV harness from the connectors on the both sides of the FL inverter and remove the FL inverter . Glass tape FL inverter LCD harness HV harness Figure 4-58 Removing the FL inverter TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual ( ...

  • Toshiba A10 - page 324

    4 Replacement Procedures 4.31 LCD unit/FL inverter 6. Remove two glass tapes and disconnect the LCD harness from the connector on the LCD unit. Glass tape Glass tape LCD harness Figure 4-59 Removing the LCD unit (1) 4-92 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 325

    4.31 LCD unit/FL inverter 4 Replacement Procedures 7. Remove the following screws and LCD unit . • M2.0 × 3C BIND screw × 4 M2.0x3C BIND LCD unit M2.0x3C BIND Figure 4-60 Removing the LCD unit (2) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-93 ...

  • Toshiba A10 - page 326

    4 Replacement Procedures 4.31 LCD unit/FL inverter 4-94 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Installing the LCD unit/FL inverter To install the LCD unit/FL inverter, follow the steps below and refer to Figure 4-56 to 4-60. 1. Place the LCD unit in place and secure it with the following screws . • M2.0 ? ...

  • Toshiba A10 - page 327

    4.32 Camera module/Wireless LAN antenna/3G antenna 4 Replacement Procedures 4.32 Camera module/Wireless LAN antenna/3G antenna Removing the Camera module/Wireless LAN antenna/3G antenna To remove the camera m odule/wireless LAN antenna/3G antenna, follow the steps below and refer to Figure 4-61. 1. Turn up the insulators (ANTENA HLD INSULATOR) and ...

  • Toshiba A10 - page 328

    4 Replacement Procedures 4.32 Camera module/Wireless LAN antenna/3G antenna 4-96 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Please prepare required parts in advance, when replacing the following item. ITEM Parts List ITEM No PART NAME Quantity 51 LCD COVER ASSY 1 75 CAMERA MODULE 1 LCD COVER ASSY 46,47 2.4/5.2G ...

  • Toshiba A10 - page 329

    4.32 Camera module/Wireless LAN antenna/3G antenna 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-97 Installing the Camera module/Wireless LAN antenna/3G antenna To install the camera module/wireless LAN antenna/3G antenna, follow the steps below and refer to Figure 4-61. 1. Stick new wire ...

  • Toshiba A10 - page 330

    4 Replacement Procedures 4.32 Camera module/Wireless LAN antenna/3G antenna (W-LAN model) 4-98 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 331

    4.32 Camera module/Wireless LAN antenna/3G antenna 4 Replacement Procedures (Web camera model) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-99 ...

  • Toshiba A10 - page 332

    4 Replacement Procedures 4.32 Camera module/Wireless LAN antenna/3G antenna (Web camera & W-LAN model) 4-100 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Peel off the separator from the camera module ...

  • Toshiba A10 - page 333

    4.32 Camera module/Wireless LAN antenna/3G antenna 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-101 ...

  • Toshiba A10 - page 334

    4 Replacement Procedures 4.33 LCD harness 4.33 LCD harness Removing the LCD harness To remove the LCD harness, follow the steps below and refer to Figure 4-62 to 4-64. 1. Turn up the insulator and release the LCD harness from the guide . LCD harness Insulator Guide Figure 4-62 Removing the LCD harness (1) 4-102 [CONFIDENTIAL] TECRA A10/S10/P10/ Sat ...

  • Toshiba A10 - page 335

    4.33 LCD harness 4 Replacement Procedures 2. Turn over the cover assembly. 3. Lift up the hook of the harness holder L and slide the harness holder L to remove it from the holes of the guides . Harness holder L Guide Hook Figure 4-63 Removing the harness holder L TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-103 ...

  • Toshiba A10 - page 336

    4 Replacement Procedures 4.33 LCD harness 4. Remove the LCD harness from the guides and pass the LCD harness through the hole of the hinge. LCD harness Hole Guide Guide Figure 4-64 Removing the LCD harness (2) Installing the LCD harness To install the LCD harness, follow the steps below and refer to Figure 4-62 to 4-64. 1. Pass the LCD harness thro ...

  • Toshiba A10 - page 337

    4.34 LCD mask 4 Replacement Procedures 4.34 LCD mask Removing the LCD mask To remove the LCD mask, follow the steps below and refer to Figure 4-65 and 4-66. 1. Remove the following screws and stand the LCD mask . CAUTION : When standing the LCD mask, hold the LCD mask with the hinge and stand them carefully. • M2.5 × 4B FLAT HEAD screw × 2 • ...

  • Toshiba A10 - page 338

    4 Replacement Procedures 4.34 LCD mask 2. Remove the LCD mask . LCD mask Hinge Figure 4-66 Removing the LCD mask (2) 4-106 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 339

    4.34 LCD mask 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-107 Installing the LCD mask To install the LCD mask, follow the steps below and refer to Figure 4-65 to 4-66. 1. Set the LCD mask to the hinge standing. 2. Lay the LCD mask down and secure it with the following screws . CAUTION : ...

  • Toshiba A10 - page 340

    4 Replacement Procedures 4.35 Hinge 4.35 Hinge Removing the Hinge To remove the hinge, follow the steps below and refer to Figure 4-67 and 4-68. 1. Remove the following screw securing the brake hinge L. • M2.5 × 6C Tapping screw × 1 2. Release two hooks and remove the brake hinge L through the hole. Brake hinge L M2.5x6C Tapping Hook Figure 4-6 ...

  • Toshiba A10 - page 341

    4.35 Hinge 4 Replacement Procedures 3. Remove the following screws securing the brake hinge R. • M2.5 × 6C Tapping screw × 2 4. Remove brake hinge R through the hole. Brake hinge R M2.5x6C Tapping M2.5x6C Tapping Figure 4-68 Removing the hinge (2) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-109 ...

  • Toshiba A10 - page 342

    4 Replacement Procedures 4.35 Hinge 4-110 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) Installing the Hinge To install the hinge, follow the steps below and refer to Figure 4-67 and 4-68. 1. Set the brake hinge R in place and secure it with the following screws . • M2.5 × 6C Tapping screw × 2 2. Set the brake ...

  • Toshiba A10 - page 343

    4.36 Fluorescent Lamp 4 Replacement Procedures TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-111 4 4.36 Fluorescent Lamp This system uses LCD modules from the following suppliers. The procedure for replacing the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. Type Part No. S ...

  • Toshiba A10 - page 344

    4 Replacement Procedures 4.36 Fluorescent Lamp 4.36.1 Replacing the 15.4-inch WXGA LG Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and backlight unit. Removing the fluorescent lamp To remove the 15.4-inch WXGA LG fluorescent lam p, follow the steps belo ...

  • Toshiba A10 - page 345

    4.36 Fluorescent Lamp 4 Replacement Procedures Disassembly of Top Case 1. Disassembly of Top Case 1 . CAUTION : Pressure or stress should not be given on PCB and COF. Figure 4-70 Replacing 15.4-inch LG fluorescent lamp (WXGA) (2) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-113 ...

  • Toshiba A10 - page 346

    4 Replacement Procedures 4.36 Fluorescent Lamp Disassembly of Source PCB 1. Disassembly of Source PCB 1 . CAUTION : Pressure or stress should not be given on PCB and COF. Figure 4-71 Replacing 15.4-inch LG fluorescent lamp (WXGA) (3) 4-114 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 347

    4.36 Fluorescent Lamp 4 Replacement Procedures Disassembly of Board Ass’y, Tape Adhesive , Sheets, Light guide, Cover Ass’y Bottom 1. Disassembly of Top Case 1 . 2. Disassembly of Board Ass’y 2 . CAUTION : This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 3. Disassembly of Tape Adhesive 3 use ...

  • Toshiba A10 - page 348

    4 Replacement Procedures 4.36 Fluorescent Lamp Installing the fluorescent lamp To install the 15.4-inch WXGA LG fluorescent lamp, follow the steps below and refer to figures 4-73 to 4-76. Assembly of Cover Ass’y, Sheets, Light guide , Tape Adhesive and Board Ass’y and Top Case 1. Assembly of Cover Ass’y and Screw (2Points) 1 . CAUTION : Maxim ...

  • Toshiba A10 - page 349

    4.36 Fluorescent Lamp 4 Replacement Procedures Assembly of Source PCB 1. Assembly of Source PCB 1 . CAUTION : Stress should not be given on COF. Figure 4-74 Replacing 15.4-inch LG fluorescent lamp (WXGA) (6) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-117 ...

  • Toshiba A10 - page 350

    4 Replacement Procedures 4.36 Fluorescent Lamp Assembly of Top Case 1. Assembly of Top Case 1 . CAUTION : Pressure should not be given on PCB and COF. Figure 4-75 Replacing 15.4-inch LG fluorescent lamp (WXGA) (7) 4-118 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 351

    4.36 Fluorescent Lamp 4 Replacement Procedures Assembly of outside tape/Cover shield 1. Assembly of Cover shield (S) 1 . CAUTION : Pressure or stress should not be given on Source PCB. Usage of gloves with anti-electric discharge coating is recommended to eliminate possible damage on circuits occurred by ESD. 2. Assembly of Tape Adhesive 2 used for ...

  • Toshiba A10 - page 352

    4 Replacement Procedures 4.36 Fluorescent Lamp 4.36.2 Replacing the 15.4-inch WXGA Samsung Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and backlight unit. Removing the fluorescent lamp To replace the 15.4-inch WXGA Samsung fluorescent lam p, follow the ...

  • Toshiba A10 - page 353

    4.36 Fluorescent Lamp 4 Replacement Procedures 2. Remove the yellow tapes, lamp-wire tape and bottom Al tape. Lamp-wire tape Bottom Al tape Yellow tape (left) Yellow tape (right) Figure 4-78 Replacing 15.4-inch Samsung fluorescent lamp (WXGA) (2) 3. Remove the top chassis from the m olded frame. CAUTION: Remove in the order of bottom hook and side ...

  • Toshiba A10 - page 354

    4 Replacement Procedures 4.36 Fluorescent Lamp 4. Separate the panel assembly and backlight unit. CAUTION : Handle with care not to damage COF of S/D. Panel assembly Figure 4-80 Replacing 15.4-inch Samsung fluorescent lamp (WXGA) (4) Installing the fluorescent lamp The installing procedure of the 15.4-inch WXGA Samsung fluorescent lam p is the reve ...

  • Toshiba A10 - page 355

    4.36 Fluorescent Lamp 4 Replacement Procedures 4.36.3 Replacing the 15.4-inch W SXGA+ Samsung Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and backlight unit. To replace the 15.4-inch WSXGA+ Samsung fluorescent lam p, follow the steps below and refer to ...

  • Toshiba A10 - page 356

    4 Replacement Procedures 4.36 Fluorescent Lamp 2. Remove the yellow tape, lamp-wire tape and bottom Al tape. Lamp-wire tape Bottom Al tape Yellow tape (left) Figure 4-82 Replacing 15.4-inch Samsung fluorescent lamp (WSXGA+) (2) 3. Separate the top chassis and molded frame. CAUTION: Remove in the order of bottom hook and side hooks. Figure 4-83 Repl ...

  • Toshiba A10 - page 357

    4.36 Fluorescent Lamp 4 Replacement Procedures 4. Separate the panel assembly and backlight unit. CAUTION : Handle with care not to damage COF of S/D and G/D ICs. Panel assembly Figure 4-84 Replacing 15.4-inch Samsung fluorescent lamp (WSXGA+) (4) Installing the fluorescent lamp The installing procedure of the 15.4-inch WSXGA+ Sam sung fluorescent ...

  • Toshiba A10 - page 358

    4 Replacement Procedures 4.36 Fluorescent Lamp 4.36.4 Replacing the 15.4-inch WXGA-CSV LG Fluorescent Lamp CAUTION : When replacing the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and backlight unit. Removing the fluorescent lamp To remove the 15.4-inch WXGA-CSV LG fluorescent lam p, follow the st ...

  • Toshiba A10 - page 359

    4.36 Fluorescent Lamp 4 Replacement Procedures Disassembly of Top Case 1. Disassembly of Top Case 1 . CAUTION : Pressure or stress should not be given on PCB and COF. Figure 4-86 Replacing 15.4-inch LG fluorescent lamp (WXGA-CSV) (2) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-127 ...

  • Toshiba A10 - page 360

    4 Replacement Procedures 4.36 Fluorescent Lamp Disassembly of Source PCB 1. Disassembly of Source PCB 1 . CAUTION : Pressure or stress should not be given on PCB and COF. Figure 4-87 Replacing 15.4-inch LG fluorescent lamp (WXGA-CSV) (3) 4-128 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 361

    4.36 Fluorescent Lamp 4 Replacement Procedures Disassembly of Board Ass’y, Tape Adhesive, Sheets, Light guide, Cover Ass’y Bottom (L) 1. Disassembly of Case top 1 . 2. Disassembly of Board Ass’y 2 . CAUTION : This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 3. Disassembly of Tape Adhesive 3 ...

  • Toshiba A10 - page 362

    4 Replacement Procedures 4.36 Fluorescent Lamp Installing the fluorescent lamp To install the 15.4-inch WXGA-CSV LG fluorescent lamp, follow the steps below and refer to figures 4-89 to 4-92. Assembly of Cover Ass’y, Sheets, Light guide, Tape Adhesive and Board Ass’y and Case top 1. Assembly of Cover Ass’y and Screw (2Points) 1 . CAUTION : Ma ...

  • Toshiba A10 - page 363

    4.36 Fluorescent Lamp 4 Replacement Procedures Assembly of Source PCB 1. Assembly of Source PCB 1 . CAUTION : Stress should not be given on COF. Figure 4-90 Replacing 15.4-inch LG fluorescent lamp (WXGA-CSV) (6) TECRA A10/S10/P10/SatellitePro S300 Maintenance Manual (960-684) [CONFIDENTIAL] 4-131 ...

  • Toshiba A10 - page 364

    4 Replacement Procedures 4.36 Fluorescent Lamp Assembly of Top Case 1. Assembly of Top Case 1 . CAUTION : Pressure should not be given on PCB and COF. Figure 4-91 Replacing 15.4-inch LG fluorescent lamp (WXGA-CSV) (7) 4-132 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 365

    4.36 Fluorescent Lamp 4 Replacement Procedures Assembly of outside tape/Cover shield 1. Assembly of Cover shield (S) 1 . CAUTION : Pressure or stress should not be given on Source PCB. Usage of gloves with anti-electric discharge coating is recommended to eliminate possible damage on circuits occurred by ESD. 2. Assembly of Tape Adhesive 2 used for ...

  • Toshiba A10 - page 366

    4 Replacement Procedures 4.36 Fluorescent Lamp 4-134 [CONFIDENTIAL] TECRA A10/S10/P10/ SatellitePro S300 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 367

    [CONFIDENTIAL] Appendices ...

  • Toshiba A10 - page 368

    Appendices App-ii [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual ( 960-684) ...

  • Toshiba A10 - page 369

    Appendices Satellite Pr o S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] App-iii Appendix Content s Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ........................................................................................ ...

  • Toshiba A10 - page 370

    Appendices App-iv [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual ( 960-684) C.12 CN4100 LAN interface connector (14-pin) ........................................................ C-17 C.13 CN4230 1394 interface connector (4-pin) .......................................................... C-17 C.14 CN4440 Bluetooth2 interface ...

  • Toshiba A10 - page 371

    Appendices Satellite Pr o S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] App-v C.39 CN6050 Int-Mic interface connector (2-pin) ...................................................... C-34 C.40 CN9300 R TCVCC interface connector (3-pin) .................................................. C-34 C.41 CN9630 System board interface c ...

  • Toshiba A10 - page 372

    Appendices App-vi [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual ( 960-684) Appendix H EC/KBC rew rite Procedur es....................................................................... H-1 Appendix I Reliability ........................................................................................................ .I - 1 ...

  • Toshiba A10 - page 373

    Appendices Satellite Pr o S300, TECRA A10/S10/P10 Maintenan ce Manual (960-684) [ CONFIDENTIAL] App-vii Figures Figure B-1 System board ( FG6IN* ) layout (front) ......................................................... B-1 Figure B-2 System board ( FG6IN* ) layout (back) ......................................................... B-3 Figure B-3 Syst ...

  • Toshiba A10 - page 374

    Appendices App-viii [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/P10 Maintenance Manual (960-684) T able B-13 ODD FPC (FGGOD*) connector (front/back) ............................................... B-17 System board(FGGI N*)(FG6IN*)(FGAIN* T able C-1 Memory A connector (200-pin) ................................................................. ...

  • Toshiba A10 - page 375

    Appendices Satellite Pr o S300, TECRA A10/S10/P10 Maintenan ce Manual (960-684) [ CONFIDENTIAL] App-ix T able C-29 EXPRESS CARD interface connector (26-pin) ............................................. C-25 T able C-30 GFX interface connector (230-pin) ............................................................. C-26 P-SW board (FG6SW*/FGGSW*/FGA ...

  • Toshiba A10 - page 376

    Appendices App-x [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual ( 960-684) T able C-50 System board interface connector (13-pin) .................................................... C-44 T able C-51 ODD interface connector (13-pin) ................................................................. C-44 T able D-1 Scan codes ...

  • Toshiba A10 - page 377

    Appendix A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it i ...

  • Toshiba A10 - page 378

    Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with co tton or a soft cloth. If it is still dirty, try breathing on the surface to create a light cond ensate and wipe it again. If the surface is very dirty, we recomme nd a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surfa ...

  • Toshiba A10 - page 379

    Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellit ...

  • Toshiba A10 - page 380

    Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly c ...

  • Toshiba A10 - page 381

    Appendix A Handling the LCD Module Appendices 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite Pro S 300, TECRA A10/S10/P 10 Mainte nance Manual ( 960-684) [CO NFIDENTIAL] A-5 ...

  • Toshiba A10 - page 382

    Appendices Appendix A Handling the LCD Module A-6 [CO NFIDENTIAL ] Satellite Pro S300, TECRA A10/S10/P10 Mai ntenance Man ual (960-684) ...

  • Toshiba A10 - page 383

    Appendix B Boar d Layout Appendices Appendix B Board Layout B.1 System board (FG6IN*) Front V iew Figure B-1 System board (FG6IN*) layout (front) Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) B-1 ...

  • Toshiba A10 - page 384

    Appendices Appendix B Boar d Layout B-2 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) Table B-1 System board (FG6IN*) connectors and ICs (front) Number Name CN21 10 PC CARD I/F connector CN2170 Smart Card I/F connector CN2600 PCI-E MINI CARD I/F connector CN2610 PCI-E MINI(3G/ROBSON) CARD I/F connector CN31 10 ...

  • Toshiba A10 - page 385

    Appendix B Boar d Layout Appendices B.2 System board (FG6IN*) Back V iew Figure B-2 System board (FG6IN*) layout (back) Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) [CONFIDENTIAL] B-3 ...

  • Toshiba A10 - page 386

    Appendices Appendix B Boar d Layout B-4 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) Table B-2 System board (FG6IN*) connectors and ICs (back) Number Name CN1400 Memory A connector CN1410 Memory B connector CN1900 SA T A HDD I/F connector CN1950 SA T A ODD I/F connector CN1970 eSA T A/USB I/F connector CN2300 ...

  • Toshiba A10 - page 387

    Appendix B Boar d Layout Appendices B.3 System board (FGGIN*) Front V iew : It is used by a GPU model. Figure B-3 System board (FGGIN*) layout (front) Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) [CONFIDENTIAL] B-5 ...

  • Toshiba A10 - page 388

    Appendices Appendix B Boar d Layout B-6 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) Table B-3 System board (FGGIN*) connectors and ICs (front) Number Name CN21 10 PC CARD I/F connector CN2170 Smart Card I/F connector CN2600 PCI-E MINI CARD I/F connector CN2610 PCI-E MINI(3G/ROBSON) CARD I/F connector CN31 10 ...

  • Toshiba A10 - page 389

    Appendix B Boar d Layout Appendices B.4 System board (FGGIN*) Back V iew : It is used by a GPU model. Figure B-4 System board (FGGIN*) layout (back) Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) [CONFIDENTIAL] B-7 ...

  • Toshiba A10 - page 390

    Appendices Appendix B Boar d Layout B-8 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) Table B-4 System board (FGGIN*) connectors and ICs (back) Number Name CN1400 Memory A connector CN1410 Memory B connector CN1900 SA T A HDD I/F connector CN1950 SA T A ODD I/F connector CN1970 eSA T A/USB I/F connector CN2300 ...

  • Toshiba A10 - page 391

    Appendix B Boar d Layout Appendices B.5 P-SW board (FG6SW*/FGGSW*/FGASW*) View (front) (back) Figure B- 5 P-SW board ( FG6SW*/FGGSW*) layout (front/back) Table B-5 P-SW board (FG6SW*/FGGSW*) connector (back) Number Name W3270 (Debugging short-circuit of a serial model) CN9600 System board I/F connector Satellite Pr o S300, TECRA A10/S10/ P10 Mainte ...

  • Toshiba A10 - page 392

    Appendices Appendix B Boar d Layout B.6 USB/MDC board (FG6US*/FGGUS*/FGAUS*) V iew (front) (back) Figure B- 6 USB/MDC board (FG6US*/FGGUS*) layout (front/back) Table B- 6 USB/MDC board (FG6US*/FGGUS*) connector s ( front/b ack) Number Name CN3010 MDC I/F connector CN4610 USB I/F connector CN4620 USB I/F connector CN4621 USB I/F connector CN9660 Sys ...

  • Toshiba A10 - page 393

    Appendix B Boar d Layout Appendices B.7 Serial board (FG6SR*/FGGSR*) V iew (front) (back) Figure B-7Serial board (FG6SR */FGGSR*) layout (front/back) Table B- 7 Serial board (FG6SR*/FGGSR*) connector ( back ) Number Name CN3420 Serial I/F connector CN9620 System board I/F connector Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ...

  • Toshiba A10 - page 394

    Appendices Appendix B Boar d Layout B.8 Sound board (FG6SN*/FGGSN*/FGASN*) V iew (front) (back) Figure B-8 Sound board (FG6SN*/FGGSN*) layout (front/back) Table B- 8 Sound board (FG6SN*/FGGSN*) connector (back) Number Name CN6050 Int-Mic I/F connector CN9300 RTCVCC I/F connector CN9630 System board I/F connector J6051 Microphone connector J6310 Hea ...

  • Toshiba A10 - page 395

    Appendix B Boar d Layout Appendices B.9 Finger/Pad Button board (FGGFS*) V iew It is used by a Fingerprint Sensor model (front) (back) Figure B-9 Finger/Pad Button board (FGGFS*) layout (front /back ) Table B-9 Finger/Pad Button b oard ( FGGFS *) connector ( back ) Number Name CN3240 Dual point I/F connector CN9650 System board I/F connector Satell ...

  • Toshiba A10 - page 396

    Appendices Appendix B Boar d Layout B.10 Pad Button board (FGGTP*) View (front) (back) Figure B-10 Pad Button board (FGGTP*) layout (front /back ) Table B-10Pad Button board (FGGTP*) connector ( back ) Number Name CN3240 Dual point I/F connector CN9650 System board I/F connector B-14 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenanc ...

  • Toshiba A10 - page 397

    Appendix B Boar d Layout Appendices B.1 1 SIM board (FGGSM*) View (front) (back) Figure B-11 SIM board (FGGSM*) layout (front /back ) Table B-11 SIM board (FGGSM*) connector ( back ) Number Name CN9670 System board I/F connector Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) [CONFIDENTIAL] B-15 ...

  • Toshiba A10 - page 398

    Appendices Appendix B Boar d Layout B.12 GPU board (FGGNM*) View : It is used by a GPU model. (front) (back) Figure B-12GPU board (FGGNM*) layout (front /back ) Table B-12 GPU board (FGGNM*) connector ( back ) Number Name CN5960 System board I/F connector B-16 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) ...

  • Toshiba A10 - page 399

    Appendix B Boar d Layout Appendices B.13 ODD FPC (FGGOD*) View (front) (back) Figure B-13 ODD FPC (FGGOD*) layout (front /back ) Table B-13 ODD FPC (FGGOD*) connector ( front/back ) Number Name CN1960 System board I/F connector CN1961 ODD I/F connector Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) [CONFIDENTIAL] B-17 ...

  • Toshiba A10 - page 400

    Appendices Appendix B Boar d Layout B-18 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/ P10 Maintenance Manual (960-684 ) ...

  • Toshiba A10 - page 401

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [CONFIDENTIAL] C- 1 Appendix C Pin Assignments System board (FG6IN*/FGGIN*/FGAIN*) C.1 CN1400 Memory A connector(200-pin) Table C-1 Memory A connector (200-pin) (1/3) Pin No. Signal Name Pin No. Signal Name 1 MRVREF-B0V 2 GND 3 GND 4 ADQ05-B1P 5 ...

  • Toshiba A10 - page 402

    Appendices Appendix C Pin Assignments C-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Table C-1 Memory A connector (200-pin) (2/3) Pin No. Signal Name Pin No. Signal Name 61 ADQ28-B1P 62 ADQ25-B1P 63 ADQ29-B1P 64 ADQ24-B1P 65 GND 66 GND 67 ADM3-B1P 68 ADQS3-B1N 69 NC 70 ADQS3-B1P 71 GND 72 GND 73 ADQ26-B1P 74 A ...

  • Toshiba A10 - page 403

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-3 Table C-1 Memory A connector (200-pin) (3/3) Pin No. Signal Name Pin No. Signal Name 133 GND 134 ADQ35-B1P 135 ADQ38-B1P 136 ADQ34-B1P 137 ADQ39-B1P 138 GND 139 GND 140 ADQ40-B1P 141 ADQ45-B1P 142 ADQ41-B1P 143 ADQ44-B1P 144 ...

  • Toshiba A10 - page 404

    Appendices Appendix C Pin Assignments C-4 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.2 CN1410 Memory B connector (200-pin) Table C-2 Memory B connector (200-pin) (1/3) Pin No. Signal Name Pin No. Signal Name 1 MRVREF-B0V 2 GND 3 GND 4 BDQ00-B1P 5 BDQ04-B1P 6 BDQ01-B1P 7 BDQ05-B1P 8 GND 9 GND 10 BDM0-B1P 11 B ...

  • Toshiba A10 - page 405

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-5 Table C-2 Memory B connector (200-pin) (2/3) Pin No. Signal Name Pin No. Signal Name 61 BDQ24-B1P 62 BDQ29-B1P 63 BDQ25-B1P 64 BDQ28-B1P 65 GND 66 GND 67 BDM3-B1P 68 BDQS3-B1N 69 NC 70 BDQS3-B1P 71 GND 72 GND 73 BDQ26-B1P 74 ...

  • Toshiba A10 - page 406

    Appendices Appendix C Pin Assignments C-6 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Table C-2 Memory B connector (200-pin) (3/3) Pin No. Signal Name Pin No. Signal Name 133 GND 134 BDQ39-B1P 135 BDQ38-B1P 136 BDQ35-B1P 137 BDQ34-B1P 138 GND 139 GND 140 BDQ44-B1P 141 BDQ40-B1P 142 BDQ45-B1P 143 BDQ41-B1P 144 G ...

  • Toshiba A10 - page 407

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-7 C.3 CN1900 SATA HDD interface connector (20-pin) Table C-3 SATA HDD interface connector (20-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 ZSTTHD-P1P 3 ZSTTHD-P1N 4 GND 5 ZSTRHD-P1N 6 ZSTRHD-P1P 7 GND 8 GND 9 GND 10 GND ...

  • Toshiba A10 - page 408

    Appendices Appendix C Pin Assignments C-8 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.5 CN1970 eSATA/USB interface connector (20-pin) Table C-5 eSATA/USB interface connector (20-pin) Pin No. Signal Name Pin No. Signal Name P1 USB0PS-E5V P2 ZUSBES-E3N P3 ZUSBES-E3P P4 GND P5 GND P6 ZSTTES-P1P P7 ZSTTES-P1N P8 ...

  • Toshiba A10 - page 409

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-9 C.6 CN2110 PC CARD interface connector (70-pin) Table C-6 PC CARD interface connector (70-pin)(1/2) Pin No. Signal Name Pin No. Signal Name 1 GND 2 ACAD00-PYP 3 ACAD01-PYP 4 ACAD03-PYP 5 ACAD05-PYP 6 ACAD07-PYP 7 ACCBE0-PYN 8 ...

  • Toshiba A10 - page 410

    Appendices Appendix C Pin Assignments C-10 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.7 CN2170 Smart Card interface connector (10-pin) Table C-7 Smart Card interface connector (10-pin) Pin No. Signal Name Pin No. Signal Name 1 SCC4-PYP 2 SCCLK-PYP 3 SCRST-PYN 4 SCVCC-PYV 5 SCDET-P3N 6 GND 7 GND 8 NC 9 SCIO-P ...

  • Toshiba A10 - page 411

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-11 C.8 CN2300 DOCKING interface connector (140-pin) Table C-8 DOCKING interface connector (140-pin) (1/3) Pin No. Signal Name Pin No. Signal Name 1 DCOUT 2 DCOUT 3 DOCDT1-S3N 4 GND 5 NC 6 NC 7 NC 8 NC 9 GND 10 ZUSBDC-E3P 11 ZUS ...

  • Toshiba A10 - page 412

    Appendices Appendix C Pin Assignments C-12 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Pin No. Signal Name Pin No. Signal Name 69 ZBIDCN-EXN 70 ZBIDCP-EXP 71 DCOUT 72 DCOUT 73 PWRSW-S3N 74 DOCVON-S3P 75 NC 76 NC 77 GND 78 GND 79 DILSON-S3P 80 NC 81 GND 82 GND 83 GND 84 GND 85 NC 86 GND 87 NC 88 GND 89 GND 90 DB ...

  • Toshiba A10 - page 413

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-13 Table C-8 DOCKING interface connector (140-pin) (3/3) Pin No. Signal Name Pin No. Signal Name A1 GND A2 GND A3 DSKDC A4 NC 1T GND 2T GND 3T GND 4T GND 5T GND 6T GND 7T GND 8T GND 9T GND 10T GND 11T GND 12T GND 13T GND 14T GN ...

  • Toshiba A10 - page 414

    Appendices Appendix C Pin Assignments C-14 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.9 CN2600 PCI-E Mini CARD interface connector (52-pin) Table C-9 PCI-E Mini CARD interface connector (52-pin) Pin No. Signal Name Pin No. Signal Name 1 PEWAKE-E3N 2 E3V 3 WCHDAT-P3P 4 GND 5 WCHCLK-P3P 6 P1V 7 WLXRQ-P3N 8 NC ...

  • Toshiba A10 - page 415

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-15 C.10 CN2610 PCI-E Mini(3G/ROBSON) CARD interface connector (52-pin) Table C-10 PCI-E Mini(3G/ROBSON) CARD interface connector (52-pin) Pin No. Signal Name Pin No. Signal Name 1 NC 2 E3V 3 NC 4 GND 5 NC 6 P1V 7 ROBXRQ-P3N 8 U ...

  • Toshiba A10 - page 416

    Appendices Appendix C Pin Assignments C-16 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.11 CN3230 Keyboard interface connector (34-pin) Table C-11 Keyboard interface connector (34-pin) Pin No. Signal Name Pin No. Signal Name 1 NUMLED-P5N 2 ARWLED-P5N 3 CAPLED-P5N 4 P5V 5 KBRT06-S3N 6 KBRT02-S3N 7 KBRT03-S3N 8 ...

  • Toshiba A10 - page 417

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-17 C.12 CN4100 LAN interface connector (14-pin) Table C-12 LAN interface connector (14-pin) Pin No. Signal Name Pin No. Signal Name 1 ACT-E3N 2 LINK-E3N 3 E3V 4 E3V 5 NC 6 NC 7 ZBIDDN-EXN 8 ZBIDDP-EXP 9 ZBIDCN-EXN 10 ZBIDCP-EXP ...

  • Toshiba A10 - page 418

    Appendices Appendix C Pin Assignments C-18 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.15 CN5000 LCD interface connector (40-pin) Table C-15 LCD interface connector (40-pin) Pin No. Signal Name Pin No. Signal Name 1 FL-P5V 2 FL-P5V 3 FL-P5V 4 NC 5 GND 6 GND 7 GND 8 PNL-P3V 9 PNL-P3V 10 FLPWM-P3P 11 GND 12 PNL ...

  • Toshiba A10 - page 419

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-19 C.16 CN6150 Speaker interface connector (4-pin) Table C-16 Speaker interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name 1 SPOTL-PXN 2 SPOTL-PXP 3 SPOTR-PXP 4 SPOTR-PXN C.17 CN8771 FAN interface connector (4-pi ...

  • Toshiba A10 - page 420

    Appendices Appendix C Pin Assignments C-20 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.20 CN9500 FGGSW* board interface connector (8-pin) Table C-20 FGGSW* board interface connector (8-pin) Pin No. Signal Name Pin No. Signal Name 1 PWRSW-S3N 2 GPBTNA-S3N 3 GPBTNB-S3N 4 PNLOFF-S3N 5 NC 6 S3V 7 SERDBG-P3N 8 GND ...

  • Toshiba A10 - page 421

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-21 C.23 CN9530 FGGSN* board interface connector (30-pin) Table C-23 FGGSN* board interface connector (30-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 XAZBC0-P3P 3 GND 4 AZSYC0-P3P 5 GND 6 AZSDO0-P3P 7 GND 8 AZSDI0-P3P 9 ...

  • Toshiba A10 - page 422

    Appendices Appendix C Pin Assignments C-22 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.24 CN9540 WebCam interface connector (6-pin) Table C-24 WebCam interface connector (6-pin) Pin No. Signal Name Pin No. Signal Name 1 P5V 2 ZUSBCM-E3N 3 ZUSBCM-E3P 4 GND 5 GND 6 CAMDET-P3N C.25 CN9550 FGGFS* board interface ...

  • Toshiba A10 - page 423

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-23 C.26 CN9560 FGGUS* board interface connector (30-pin) Table C-26 FGGUS* board interface connector (30-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 XAZBC1-P3P 3 GND 4 AZRST1-E3N 5 AZSDIM-P3P 6 AZSYC1-P3P 7 E3V 8 AZSDO ...

  • Toshiba A10 - page 424

    Appendices Appendix C Pin Assignments C-24 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.28 IS2140 MEDIA BRIDGE interface connector (46-pin) Table C-28 MEDIA BRIDGE interface connector (46-pin) Pin No. Signal Name Pin No. Signal Name 1 SDCD-P3N 2 GND 3 SDDAT1-P3P 4 SDDAT0-P3P 5 NC 6 GND 7 NC 8 SDCLK-P3P 9 GND 1 ...

  • Toshiba A10 - page 425

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-25 C.29 IS2520 EXPRESS CARD interface connector (26-pin) Table C-29 EXPRESS CARD interface connector (26-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 ZUSBEX-E3N 3 ZUSBEX-E3P 4 CPUSB-E3N 5 NC 6 NC 7 E3V 8 E3V 9 P1V 10 P1 ...

  • Toshiba A10 - page 426

    Appendices Appendix C Pin Assignments C-26 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.30 CN5900 GFX interface connector (230-pin) Table C-30 GFX interface connector (230-pin)(1/4) Pin No. Signal Name Pin No. Signal Name 1 PVT-EFV 2 1R8-E1V 3 PVT-EFV 4 1R8-E1V 5 PVT-EFV 6 1R8-E1V 7 PVT-EFV 8 1R8-E1V 9 PVT-EFV ...

  • Toshiba A10 - page 427

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-27 Pin No. Signal Name Pin No. Signal Name 71 GND 72 ZECG08-P1P 73 ZEGC07-P1N 74 GND 75 ZEGC07-P1P 76 ZECG07-P1N 77 GND 78 ZECG07-P1P 79 ZEGC06-P1N 80 GND 81 ZEGC06-P1P 82 ZECG06-P1N 83 GND 84 ZECG06-P1P 85 ZEGC05-P1N 86 GND 87 ...

  • Toshiba A10 - page 428

    Appendices Appendix C Pin Assignments C-28 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Pin No. Signal Name Pin No. Signal Name 145 NVASDA-P5P 146 GND 147 NC 148 XNLCK1-PYP 149 NC 150 XNLCK1-PYN 151 GND 152 GND 153 NVCSCL-P3P 154 NC 155 NVCSDA-P3P 156 NC 157 NC 158 NC 159 GND 160 ZNLTX6-PYP 161 NVCRED-PXP 162 ZN ...

  • Toshiba A10 - page 429

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-29 Table C-30 GFX interface connector (230-pin)(4/4) Pin No. Signal Name Pin No. Signal Name 219 ZNDTX1-P3N 220 NVESDA-P5P 221 ZNDTX1-P3P 222 NC 223 GND 224 GND 225 ZNDTX0-P3N 226 P3V 227 ZNDTX0-P3P 228 P3V 229 GND 230 P3V ...

  • Toshiba A10 - page 430

    Appendices Appendix C Pin Assignments C-30 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) P-SW board (FG6SW*/FGGSW*/FGASW*) C.31 CN9500 System board interface connector (4-pin) Table C-31 System board interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 SERDBG-P3N 3 S3V 4 PNLROT-S3N 5 PNLOFF ...

  • Toshiba A10 - page 431

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-31 USB/MDC board (FG6US*/FGGUS*/FGAUS*) C.32 CN3010 MDC interface connector (12-pin) Table C-32 MDC interface connector (12-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 NC 3 AZSDO1-P3P 4 NC 5 GND 6 E3V 7 AZSYC1-P3P 8 GN ...

  • Toshiba A10 - page 432

    Appendices Appendix C Pin Assignments C-32 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.35 CN4621 USB interface connector (4-pin) Table C-35 USB interface connector (4-pin) Pin No. Signal Name Pin No. Signal Name 1 USB1PS-E5V 2 ZUSBP0-E3N 3 ZUSBP0-E3P 4 GND 1T GND 2T GND 3T GND C.36 CN9660 System board interfa ...

  • Toshiba A10 - page 433

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-33 Serial board (FG6SR*/FGGSR*) C.37 CN3420 Serial interface connector (9-pin) Table C-37 Serial interface connector (9-pin) Pin No. Signal Name Pin No. Signal Name 1 DCD-PYP 2 RXD-PYN 3 TXD-PYN 4 DTR-PYP 5 GND 6 DSR-PYP 7 RTS- ...

  • Toshiba A10 - page 434

    Appendices Appendix C Pin Assignments C-34 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Sound board (FG6SN*/FGGSN*/FGASN*) C.39 CN6050 Int-Mic interface connector (2-pin) Table C-39 Int-Mic interface connector (2-pin) Pin No. Signal Name Pin No. Signal Name 1 IMICIN-PXP 2 GND C.40 CN9300 RTCVCC interface connect ...

  • Toshiba A10 - page 435

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-35 C.41 CN9630 System board interface connector (30-pin) Table C-41 System board interface connector (30-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 XAZBC0-P3P 3 GND 4 AZSYC0-P3P 5 GND 6 AZSDO0-P3P 7 GND 8 AZSDI0-P3P 9 ...

  • Toshiba A10 - page 436

    Appendices Appendix C Pin Assignments C-36 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) C.42 J6051 Microphone connector (6-pin) Table C-42 Microphone connector (6-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 EMICIN-PXP 3 EMICB-P2V 4 GND 5 DETCTA-P4N 6 EMICB-P2V C.43 J6310 Headphone connector (6-pin) Tabl ...

  • Toshiba A10 - page 437

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-37 Finger/Pad Button board (FGGFS*) C.44 CN3240 Dual point interface connector (12-pin) Table C-44 Dual point interface connector (12-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 TPBTNL-P5N 3 TPBTNR-P5N 4 NC 5 SP-P5V 6 ...

  • Toshiba A10 - page 438

    Appendices Appendix C Pin Assignments C-38 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Pad Button board (FGGTP*) C.46 CN3240 Dual point interface connector (12-pin) Table C-46 Dual point interface connector (12-pin) Pin No. Signal Name Pin No. Signal Name 1 GND 2 TPBTNL-P5N 3 TPBTNR-P5N 4 NC 5 SP-P5V 6 SPX-PXP ...

  • Toshiba A10 - page 439

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-39 SIM board (FGGSM*) C.48 CN9670 System board interface connector (10-pin) Table C-48 System board interface connector (10-pin) Pin No. Signal Name Pin No. Signal Name 1 UIMPWR-E3V 2 UIMRST-E3P 3 GND 4 GND 5 UIMCLK-E3P 6 GND 7 ...

  • Toshiba A10 - page 440

    Appendices Appendix C Pin Assignments C-40 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) GPU board (FGGNM*) C.49 CN2451 System board interface connector (230-pin) Table C-49 System board interface connector (230-pin) (1/4) Pin No. Signal Name Pin No. Signal Name 1 PVT-EFV 2 1R8-E1V 3 PVT-EFV 4 1R8-E1V 5 PVT-EFV 6 ...

  • Toshiba A10 - page 441

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-41 Table C-49 System board interface connector (230-pin) (2/4) Pin No. Signal Name Pin No. Signal Name 65 GND 66 ZECG09-P1P 67 ZEGC08-P1N 68 GND 69 ZEGC08-P1P 70 ZECG08-P1N 71 GND 72 ZECG08-P1P 73 ZEGC07-P1N 74 GND 75 ZEGC07-P1 ...

  • Toshiba A10 - page 442

    Appendices Appendix C Pin Assignments C-42 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) Pin No. Signal Name Pin No. Signal Name 137 GTHERM-P3N 138 GND 139 HSYNCA-P3P 140 NVAGRN-PXP 141 VSYNCA-P3P 142 GND 143 NVASCL-P5P 144 NVABLU-PXP 145 NVASDA-P5P 146 GND 147 NC 148 XLCK1-PYP 149 NC 150 XLSK1-PYN 151 GND 152 GN ...

  • Toshiba A10 - page 443

    Appendix C Pin Assignments Appendices Satellite Pro S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [CONFIDENTIAL] C-43 Pin No. Signal Name Pin No. Signal Name 209 XTCK0-P3P 210 M5V 211 GND 212 IC5970-4pin 213 ZTTX2-P3N 214 FLPWM-P3P 215 ZTTX2-P3P 216 FLVEN-P3P 217 GND 218 NVESCL-P5P 219 ZTTX1-P3N 220 NVESDA-P5P 221 ZTTX1-P3P 222 NC 223 GND 2 ...

  • Toshiba A10 - page 444

    Appendices Appendix C Pin Assignments C-44 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ODD FPC (FGGOD*) C.50 CN1960 System board interface connector (13-pin) Table C-50 System board interface connector (13-pin) Pin No. Signal Name Pin No. Signal Name S1 GND S2 ZSTTOD-P1P S3 ZSTTOD-P1N S4 GND S5 ZSTROD-P1N S6 ZS ...

  • Toshiba A10 - page 445

    Appendix D Keyboard Scan/Character Codes Appendices Satellite Pro S300, TECRA A10/S1 0/P10 Maintena nce Manual ( 960-684) [ CONFIDENTIAL] D- 1 Appendix. D Appendix D Keyboard Scan/Character Codes D.1 Scan Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! ...

  • Toshiba A10 - page 446

    Appendices Appendix D Keyboard Scan/Character Codes D-2 [ CONFIDENTIAL] Satellite Pro S300, TECRA A10/ S10/P10 Mainte nance Manual ( 960-684) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 2 ...

  • Toshiba A10 - page 447

    Appendix D Keyboard Scan/Character Codes Appendices QOSMIO G50 Maint enance Manual ( 960-683) [CONFIDENTIAL] D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 5 ...

  • Toshiba A10 - page 448

    Appendices Appendix D Keyboard Scan/Character Codes D-4 [ CONFIDENTIAL] Satellite Pro S300, TECRA A10/ S10/P10 Mainte nance Manual ( 960-684) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 * ...

  • Toshiba A10 - page 449

    Appendix D Keyboard Scan/Character Codes Appendices QOSMIO G50 Maint enance Manual ( 960-683) [CONFIDENTIAL] D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 ...

  • Toshiba A10 - page 450

    Appendices Appendix D Keyboard Scan/Character Codes D-6 [ CONFIDENTIAL] Satellite Pro S300, TECRA A10/ S10/P10 Mainte nance Manual ( 960-684) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Brea k Make Brea k 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 ...

  • Toshiba A10 - page 451

    Appendix D Keyboard Scan/Character Codes Appendices QOSMIO G50 Maint enance Manual ( 960-683) [CONFIDENTIAL] D-7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 ...

  • Toshiba A10 - page 452

    Appendices Appendix D Keyboard Scan/Character Codes D-8 [ CONFIDENTIAL] Satellite Pro S300, TECRA A10/ S10/P10 Mainte nance Manual ( 960-684) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co m mo n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes. ...

  • Toshiba A10 - page 453

    Appendix E Key Layout Appendices 4 Appendix E Key Layout 4.31 E.1 United Kingdom (UK) Keyboard Figur e E-1 UK keyboar d 4.31 E.2 United States (US) Keyboard Figur e E-2 US keyboar d Satellite Pr o S300, TECRA A10/S10/P10 Mainte nance Manual (960-684) [ CONFIDENTIAL] E-1 ...

  • Toshiba A10 - page 454

    Appendices Appendix E Key Layout E-2 [CONFIDENTIAL] Satellite Pr o S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 455

    Appendix F W iring diagrams Appendices 4 Appendix F Wiring diagrams F.1 RGB Monitor Loopback Connector Figur e F-1 RGB Monitor Loopback Connector F.2 RS-232C Loopback Connector Figur e F-2 RS-232C Loopback Connector Satellite Pr o S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [CONFIDENTIAL] F-1 ...

  • Toshiba A10 - page 456

    Appendices Appendix F W iring diagrams F.3 RS-232C direct connection cable (9-pin to 9-pin) Figur e F-3 RS-232C dir ect connection cable (9-pin to 9-pin) F.4 RS-232C direct connection cable (9-pin to 25-pin) Figur e F-4 RS-232C dir ect connection cable (9-pin to 25-pin) F-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/ P10 Maintenance Manual (9 ...

  • Toshiba A10 - page 457

    Appendix F W iring diagrams Appendices F.5 LAN Loopback Connector Figur e F-5 LAN Loopback Connector Satellite Pr o S300, TECRA A10/S10/P10 Maintenance Manual (960-684) [CONFIDENTIAL] F-3 ...

  • Toshiba A10 - page 458

    Appendices Appendix F W iring diagrams F-4 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/ P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 459

    Appendix G BIOS r ewrite pr ocedures Appendices Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite th e system BIOS program when you update the system BIOS. Tools T o rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk Rewriting the BIOS 1. Set the system to boot mode. 2. T urn of f the pow ...

  • Toshiba A10 - page 460

    Appendices Appendix G BIOS r ewrite pr ocedures G-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 461

    Appendix H EC/KBC r ewrite pr ocedures Appendices Satellite Pr o S300, TECRA A10/S10/P10 Maintenance Manual (960-684)[CONFIDENTIAL] H-1 Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite th e EC/KBC system program when you update the EC/KBC system. It is necessary to rewrite the EC/KBC system program when the foll ...

  • Toshiba A10 - page 462

    Appendices Appendix H EC/KBC r ewrite pr ocedures H-2 [CONFIDENTIAL] Satellite Pro S300, TECRA A10/S10/P10 Maintenance Manual (960-684) ...

  • Toshiba A10 - page 463

    Appendix I Reliability Appendices Satellite Pro S300, TECRA A10/ S1 0/P 10 Mainte na nce Manual (960-68 4)[ CO NFID E NTIAL ] I-1 Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures ) in maximum configuration. Table I-1 MTBF Time (hours) 5,182 ｈ ...

  • Toshiba A10 - page 464

    Appendices Appendix I Reliability I-2 [CONFIDENTIAL ] Satellite Pro S300, TECRA A10/S10/P 10 Mainte na nce Man ual (960-684) ...

Produzent Toshiba Kategorie Laptop

Dokumente, die wir vom Produzenten des Geräts Toshiba A10 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Toshiba
- Bedienungsanleitungen A10
- Produktkarten Toshiba
- Informationsbroschüren
- oder Energieetiketten Toshiba A10
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Toshiba A10.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Toshiba A10, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Toshiba A10. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Toshiba A10 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Toshiba A10, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Toshiba A10 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Toshiba A10 verständlich ist.

Eine gänzliche Bedienungsanleitung von Toshiba sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Toshiba A10 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Toshiba A10 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Toshiba A10, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Toshiba A10 - die uns die ersten Schritte während der Nutzung von Toshiba A10 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Toshiba A10 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Toshiba A10 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Toshiba A10?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Toshiba A10 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Toshiba A10 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)