Bedienungsanleitung Renesas FP-128

22 Seiten 0.44 mb
Download

Zur Seite of 22

Summary
  • Renesas FP-128 - page 1

    H8S/2636 Series FP-128 User System Interface Cable (HS2636ECH61H) for E6000 Emulator User’s Manual HS2636ECH61HE(B) ...

  • Renesas FP-128 - page 2

    Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...

  • Renesas FP-128 - page 3

    i Preface Thank you for purchasing this user system interface cable (HS2636ECH61H) for the Renesas’s original mi crocomputer H8S/2636 series. The HS2636ECH61H is a user system interface cable that connects an H8S/2636 and H8S/2646 series E6000 em ulator (HS2646EPI61H; hereinafte r referred to as the emulator) t o the IC socket for a FP-128 packag ...

  • Renesas FP-128 - page 4

    ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 4 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 4 2.2 Connecti ...

  • Renesas FP-128 - page 5

    1 Section 1 Configuration CAUTION Use an NQPACK128RD socket (manufactured by Tokyo Eletech Corporation) for the FP-128 package IC socket on the user system. Figure 1 shows the configuration of the HS2636E CH61H user system interface cable for the FP-128 package. ...

  • Renesas FP-128 - page 6

    Figure 1 HS2636ECH61H User System Interface Cable 2 ...

  • Renesas FP-128 - page 7

    3 Table 1 lists t he HS2636ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2636ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-128 package 4 Socket cover 1 For installing anFP-128 packaged MCU 5 Screws (M2 x 10 mm) 4 For fastening cab ...

  • Renesas FP-128 - page 8

    Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system a ...

  • Renesas FP-128 - page 9

    Figure 2 Connecting User System Int erface Cable to Emulator Station 5 ...

  • Renesas FP-128 - page 10

    2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the ...

  • Renesas FP-128 - page 11

    User system Guide pins 4 projections to apply epoxy resin adhesive to Bottom view of IC soket Pin 1 Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for an FP-128 package to the user system. Be sure t o completely solder the leads so that the sold er slops gently over the lead s and forms solder ...

  • Renesas FP-128 - page 12

    8 2.2.4 Fastening Cable Head CAUTION 1. Use the screwdriber provided for tightening screw s. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightene ...

  • Renesas FP-128 - page 13

    Figure 4 Connecting User System Interface Cable to User System 9 ...

  • Renesas FP-128 - page 14

    2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 5 Fastening Cable Body 10 ...

  • Renesas FP-128 - page 15

    2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an FP-128 package (NQPACK128RD: m anufactured by Tokyo Elet ech Corporation). Not e that the dimensions in figure 6 are somewhat different from those of t he actual chip's m o ...

  • Renesas FP-128 - page 16

    2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 12 ...

  • Renesas FP-128 - page 17

    2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Connecting User System Interface Cable 13 ...

  • Renesas FP-128 - page 18

    14 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screw s. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly ...

  • Renesas FP-128 - page 19

    Figure 9 Installing MCU to User System 15 ...

  • Renesas FP-128 - page 20

    Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2636 series, turn on the emulator according to the procedures described in the H8S Series E6000 Em ulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and ports to check the bus states of the pi ...

  • Renesas FP-128 - page 21

    Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifi ...

  • Renesas FP-128 - page 22

    6. The P1 jumper socket is used for t esting. Do not remove t he inserted jumper pin. P1 3 2 1 Figure 12 P1 Jumper Socket 18 ...

Produzent Renesas Kategorie Computer Hardware

Dokumente, die wir vom Produzenten des Geräts Renesas FP-128 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Renesas
- Bedienungsanleitungen FP-128
- Produktkarten Renesas
- Informationsbroschüren
- oder Energieetiketten Renesas FP-128
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Renesas FP-128.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Renesas FP-128, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Renesas FP-128. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Renesas FP-128 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Renesas FP-128, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Renesas FP-128 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Renesas FP-128 verständlich ist.

Eine gänzliche Bedienungsanleitung von Renesas sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Renesas FP-128 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Renesas FP-128 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Renesas FP-128, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Renesas FP-128 - die uns die ersten Schritte während der Nutzung von Renesas FP-128 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Renesas FP-128 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Renesas FP-128 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Renesas FP-128?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Renesas FP-128 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Renesas FP-128 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)