Bedienungsanleitung National Instruments NI 9852

27 Seiten 0.32 mb
Download

Zur Seite of 27

Summary
  • National Instruments NI 9852 - page 1

    OPERATING INSTRUCTIONS NI 9852 2-Port, Low-Spe ed/Fault-Tolerant CAN Module ...

  • National Instruments NI 9852 - page 2

    NI 9852 Operating Instructions 2 ni.com These operating instructions desc ribe ho w to use the Natio nal Instruments (NI) 9852 module. F o r information about installing, configuring, and programming your system, refer to your system documentation. The NI 9852 module requires the NI 985 x softw are (version 1.2 o r higher) to be inst alled. The lat ...

  • National Instruments NI 9852 - page 3

    © National Instruments Corp. 3 NI 9852 Operating Instructions Safety Guidelines fo r Hazardous Loca tions The NI 9852 is suitable for use in Cl ass I, Division 2, Groups A, B, C, D, and T4 hazardous locations; Class 1, Zone 2, AEx nA II T4 and Ex nA II T4 hazardous loca tions; and nonhazardous locations only . Follo w these guidelines if you are i ...

  • National Instruments NI 9852 - page 4

    NI 9852 Operating Instructions 4 ni.com Caution For Zone 2 applications, install a protection device between the CAN signals and the NI 9852 CAN pins. The de vice must pre v ent the CAN Port-to-COM voltage from e xceeding 55 V if there is a transient ov ervoltage condition. Special Conditions for Hazard ous Locations Use in Europe This equipment ha ...

  • National Instruments NI 9852 - page 5

    © National Instruments Corp. 5 NI 9852 Operating Instructions Each port has two isolat ed common pins (COM) that are internally connected to the isolated referenc e of the module and serve as the reference ground for CAN_H and CAN_L. Connect the CAN bus reference ground (sometimes referre d to as CAN_V–) to the COM pin. Each port also has an opt ...

  • National Instruments NI 9852 - page 6

    NI 9852 Operating Instructions 6 ni.com Table 1. Pin Assignments for CAN0 Connector Pin Signal 1 No Connection (NC) 2 CAN_L 3 COM0 4 NC 5 SHLD 6 COM0 7 CAN_H 8 NC 9 V SUP0 6 7 8 9 1 2 3 4 5 ...

  • National Instruments NI 9852 - page 7

    © National Instruments Corp. 7 NI 9852 Operating Instructions Table 2. Pin Assignments for CAN1 Connector Pin Signal 1 No Connection (NC) 2 CAN_L 3 COM1 4 NC 5 SHLD 6 COM1 7 CAN_H 8 NC 9 V SUP1 6 7 8 9 1 2 3 4 5 ...

  • National Instruments NI 9852 - page 8

    NI 9852 Operating Instructions 8 ni.com CAN Bus T opology and T e rmination A CAN bus consists of two or more CAN nodes cabled together . The CAN_H and CAN_L pins of each node are connected to the main CAN bus cable through a short con nection kno wn as a “stub . ” The pair of signal wires, CAN_H and CAN_L constitutes a transmission line. Every ...

  • National Instruments NI 9852 - page 9

    © National Instruments Corp. 9 NI 9852 Operating Instructions Figure 1. CAN Bus T opology and T ermination Resistor Lo cations Connecting a CAN Bus to the NI 9852 Each port of the NI 9852 can be connected to any location on a CAN bus. Figure 2 shows one exam ple of the con nection of CAN0 of the NI 9852 directly to one C AN node, and CAN1 directly ...

  • National Instruments NI 9852 - page 10

    NI 9852 Operating Instructions 10 ni.com Figure 2. Connecting Both Ports of th e NI 9852 to CAN Buses CAN1 CAN Device CAN0 NI 9852 CAN Cable (With Optional Shield) (SHLD) CAN_H CAN_L V sup1 COM1 (SHLD) CAN_H CAN_L V sup1 COM1 CAN Device CAN Cable (With Optional Shield) (SHLD) CAN_H CAN_L V sup0 COM0 (SHLD) CAN_H CAN_L V sup0 COM0 + – External Pow ...

  • National Instruments NI 9852 - page 11

    © National Instruments Corp. 11 NI 9852 Operating Instructions Cabling Requirements for NI 9852 This section deals wi th cabling specif icatio ns, termination resistors, cable lengths, and the number of CAN nodes that can exist in a system. Cable Specifications Cables should meet th e physical medium re quirements specified in ISO 11898, sho wn in ...

  • National Instruments NI 9852 - page 12

    NI 9852 Operating Instructions 12 ni.com Determining the Necessary T ermination Resistance for the Board Unlike High-Speed CAN, Low- Speed/F ault-T olerant CAN requires termination at the Lo w-Speed/F ault-T olerant CAN transceiv er instead of on the cable itself. T ermination requires two resistors, R TH for CAN_H and R TL for CAN_L. This configu ...

  • National Instruments NI 9852 - page 13

    © National Instruments Corp. 13 NI 9852 Operating Instructions Number of CAN Nodes The maximum number of nodes depends on the electrical characteristics of the nodes on the ne twor k. If all of the nodes meet the requirements of Lo w-Spee d/Fault-T olerant CAN, up to 32 nodes may be connected to the b us. NI 9852 Hardware Over view The NI 9852 has ...

  • National Instruments NI 9852 - page 14

    NI 9852 Operating Instructions 14 ni.com Figure 3. NI 9852 Hardware Overview + _ + _ V SUP0 Ext Pwr Supply 0 COM0 CAN_H CAN_L Ext Pwr Supply 1 V SUP1 COM1 CAN_H CAN_L CAN0 CAN1 CAN T ransceiv er +5 V Reg CAN T ransceiv er +5 V Reg Rx Rx Rx Rx Tx Tx Tx Tx CAN Controller CAN Controller ...

  • National Instruments NI 9852 - page 15

    © National Instruments Corp. 15 NI 9852 Operating Instructions Sleep Mode (CompactRIO Only) Y ou can enable sleep mode fo r the CompactRIO system in software. In sleep mode, the syst em consumes less power and may dissipate less heat. T ypically , when a system is in sleep mode, you cannot communicate with th e modules. Refer to the Spec ification ...

  • National Instruments NI 9852 - page 16

    NI 9852 Operating Instructions 16 ni.com Specifications The follo wing spec ificat ions are typical for the range – 40 to 70 °C unless otherwise noted. Low-Speed/Fault-T olerant CAN Characteristics T ranscei ver ............ ........... ............ ..... Philips TJ A1054A Max baud rate .............. ........... .......... 125 Kbps CAN_H, CAN_L ...

  • National Instruments NI 9852 - page 17

    © National Instruments Corp. 17 NI 9852 Operating Instructions Note Contact NI for Bellcore MTBF specifications at other temperatures or for MIL-HDBK -217F specifications. Power Requirements Power consumption from chassis Activ e mode T ransmitting ............. ............ 400 mW max Receiving ........ ........... .......... 400 mW max Sleep mod ...

  • National Instruments NI 9852 - page 18

    NI 9852 Operating Instructions 18 ni.com Safety Maximum Voltage 1 Connect only v oltages that are wi thin these limits. Port-to-COM ....... ...................... ........ –27 to +40 VDC max, Measurement Category I Measurement Cate gory I is f or measurements performed on circuits not directly connected to the electrical distribution system refer ...

  • National Instruments NI 9852 - page 19

    © National Instruments Corp. 19 NI 9852 Operating Instructions Isolation Voltages Port-to-port W ithstand .......... ............ ........... ... 500 V rms , 5 s Continuous .......... ........... ........... . 6 0 VDC, Measurement Category I Port-to-earth ground W ithstand .......... ............ ........... ... 500 V rms , 5 s Continuous ........ ...

  • National Instruments NI 9852 - page 20

    NI 9852 Operating Instructions 20 ni.com Hazardous Locations U.S. (UL) ........ ........... ........... ........... . Class I, Di vision 2, Groups A, B, C, D, T4; Class I, Zone 2, AEx nA II T4 Canada (C-UL) ..................... ........... . C lass I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, Ex nA II T4 Europe (DEMKO)................. . ...

  • National Instruments NI 9852 - page 21

    © National Instruments Corp. 21 NI 9852 Operating Instructions Storage humid ity .......... ........... .......... 5 to 95% RH, noncondensing Maximum altitude.......... ......... .......... 2,000 m Pollution Degree (IEC 60664) .......... 2 Shock and Vibration T o meet these spec ifications, you must pan el mount the CompactRIO system . Operating v ...

  • National Instruments NI 9852 - page 22

    NI 9852 Operating Instructions 22 ni.com Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electica l equipment for measurement, control, and laboratory use: • EN 61326 EMC requirement s; Minimum Immunity • EN 55011 Emissions; Group 1, Class A • CE, C-Tick, ICES, and FCC Par ...

  • National Instruments NI 9852 - page 23

    © National Instruments Corp. 23 NI 9852 Operating Instructions Note Refer to the Declaration of Co nformity (DoC) for this product for any additio nal regulatory compliance information. T o obtain the DoC for this product, visit ni.com/certification , search by model number or product line, and clic k th e appropriate link in the Certification col ...

  • National Instruments NI 9852 - page 24

    NI 9852 Operating Instructions 24 ni.com Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of their life c ycle, all products must be sent to a WEEE recycling center . For more information about WEEE recy cling centers and National Instruments WEEE initiativ es, visit ni.com/ environment/weee.htm . ⬉ᄤֵᙃѻક∵ᶧ᥻? ...

  • National Instruments NI 9852 - page 25

    © National Instruments Corp. 25 NI 9852 Operating Instructions National Instruments Contact Information National Instruments corporate headquarters is located at 11500 North Mopac Expressway , Austin, T exas, 78759-3504. National Instruments also has of fi ces located around the world to help address your support needs. F or telephone support in t ...

  • National Instruments NI 9852 - page 26

    NI 9852 Operating Instructions 26 ni.com South Africa 27 0 11 805 8197, Spain 34 91 640 0085, Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, T aiwan 886 02 2377 2222, Thailand 662 278 6777, T urk ey 90 212 279 3031, United Kingdom 44 (0) 1635 523545 ...

  • National Instruments NI 9852 - page 27

    © 2006–2008 Nati onal Instruments Corp. All rights reserved. 371849B-01 Jun08 National Instruments, NI, n i.com, and LabVIEW are trademarks of National Instruments C orporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names ment ioned herein are trade ...

Produzent National Instruments Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts National Instruments NI 9852 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen National Instruments
- Bedienungsanleitungen NI 9852
- Produktkarten National Instruments
- Informationsbroschüren
- oder Energieetiketten National Instruments NI 9852
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung National Instruments NI 9852.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen National Instruments NI 9852, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen National Instruments NI 9852. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts National Instruments NI 9852 ansehen.

Die komplette Bedienungsanleitung des Geräts National Instruments NI 9852, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von National Instruments NI 9852 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von National Instruments NI 9852 verständlich ist.

Eine gänzliche Bedienungsanleitung von National Instruments sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von National Instruments NI 9852 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von National Instruments NI 9852 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich National Instruments NI 9852, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts National Instruments NI 9852 - die uns die ersten Schritte während der Nutzung von National Instruments NI 9852 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit National Instruments NI 9852 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von National Instruments NI 9852 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich National Instruments NI 9852?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit National Instruments NI 9852 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit National Instruments NI 9852 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)