Bedienungsanleitung Jensen MCD10

17 Seiten 0.54 mb
Download

Zur Seite of 17

Summary
  • Jensen MCD10 - page 1

    Thank Y ou! Thank you for choosing a JENSEN product. We’ve tried to make the instructions in this owner ’s manual clear and easy to follow . If you take a few mi nutes to look through it , you’ll learn how to use all of the features of your new JENSEN marine stereo for maximum e njoyment. Introduction . . . . . . . . . . . . . . . . . . . . . ...

  • Jensen MCD10 - page 2

    2 MCD10 Pr eparation Getting S tarted It’s a good idea to read all of the in structions before beginning the installation. We recommend having your JENSEN 10-Disc CD changer in stalled by a reputable installation shop. T ools and Supplies The following tools and supplies are nee ded to install the CD changer . • T orx type, flat-head and Philli ...

  • Jensen MCD10 - page 3

    3 MCD10 Prepar ation (continued) Trans port Lock Screws The mechanism in the CD changer is "locked" in to place during shipment by transport screws. Be sure to remove the screws prio r to installation. Retain these screws for future use when transporting the unit for service/maintenance. Afte r removing the transport lock screws, pla ce t ...

  • Jensen MCD10 - page 4

    4 MCD10 7. Asegúrese de utilizar los tornillos provistos. No utilice ningún tornillo que sea parte del sistema de freno o de la dirección para instalar la unidad. 8. Asegúrese de no enganchar ningún cable cuando esté ajustando los tornillos. 9. Esta unidad no se puede instalar de lado, mirando hacia atrás o de arriba hacia abajo. La instalac ...

  • Jensen MCD10 - page 5

    5 MCD10 Setting the An ti-vibration B oard The unit can be installed horizontally , vertically , at a 45° angle, or susp ended. The position of the built-in anti-vibration springs (left and righ t side) must correspond to the mounting position chosen. If the springs are not set correctly for t he type of installation chosen, the anti-vibration com ...

  • Jensen MCD10 - page 6

    6 MCD10 Installation (continued) Horizontal Installation 1. Make sure the anti-vibration springs are set to position "0". 2. Attach a bracket (A) to each side of the unit using the machine screws (M4x5). 3. Attach the brackets (A) to the mounting base (B) using the hex agonal bolts (M6x12) and M6 flat and split washers. 4. Determine the m ...

  • Jensen MCD10 - page 7

    7 MCD10 Flat Surface a. S tick the su pplied double-sided tape to t he bottom of the mounting bases (B) and peel off the paper backing. b. Drill holes for the self- tapping screws (T5x12). c. Install self-tapping screws to secure the mounting base to the surface. d. Affix the unit to the floor by pressing in place. Carpeted Surface a. Pull the carp ...

  • Jensen MCD10 - page 8

    8 MCD10 Installation (continued) V ertical Installation 1. Make sure the anti-vibration springs are set to position "90". 2. Attach a bracket (A) bracket to each side of the unit using the machine screws (M4x5). 3. Attach the brackets (A) to the mounti ng base (B) using the hexagonal bolts (M6x12) and M6 flat and split washers. 4. Determi ...

  • Jensen MCD10 - page 9

    9 MCD10 Flat Surface a. S tick the supplied double-sided tape to the bottom of the mountin g bases (B) and peel off the paper backing. b. Drill holes for the se lf-tapping screws (T5x12). c. Install self-tapping screws to secu re the mounting base to the surface. d. Affix the unit to the floor by pressing in place. Carpeted Surface a. Pull the carp ...

  • Jensen MCD10 - page 10

    10 MCD10 Installa tion (continued) 45° Angle Installation 1. Make sure the anti-vibration springs ar e set to position "45". 2. Attach a bracket (A) to each side of t he unit using the machine scre ws (M4x5). 3. Attach the brackets (A) to the mounting base (B) using the hexagonal bolts (M6x12) and M6 flat and split washers. 4. Determine ...

  • Jensen MCD10 - page 11

    11 MCD10 Flat Surface a. S tick the supplied double-sided tape to the bottom of the mounting bases (B) and peel off the paper backing. b. Drill holes for the self-tapping screws (T5x12). c. Install self-tapping screws to secure the mounting base to the surface. d. Affix the unit to the floor by pressing in place. Carpeted Surf ace a. Pull the carpe ...

  • Jensen MCD10 - page 12

    12 MCD10 Installation (continued) Suspended Installation 1. Make sure the anti-vibration springs are set to position "0". 2. Attach a bracket (A) to each side of t he unit using the machine screws (M4x5). 3. Determine the mounting location for the unit. 4. Drill holes for the self-tapping screws (T5x12). 5. Install self-tapping screws to ...

  • Jensen MCD10 - page 13

    13 MCD10 Wiring / Cableado / Cablage IMPORT ANT : Incorrect wirin g connections can damage the unit. Fol low the wiring instructions carefully, or have the installation handled b y an experienced technician. IMPORT ANTE: Una con exión incorrecta de los cables p uede dañar la unidad. Siga las instrucciones del cableado cuid adosamente o haga que u ...

  • Jensen MCD10 - page 14

    14 MCD10 Oper ation Loading the CD Change r Inserting Compact Discs in the Magazine 1. Grip the tab on the magazine tray into wh ich you will be loading a disc and pull it out gently . Pull out only one tray at a time. 2. Insert a disc into the tray with the label side up (play surface facing down). 3. Push the tray back into the magazine. Load dis ...

  • Jensen MCD10 - page 15

    15 MCD10 Cargando el Cambiador de CD (Continuación) Cargando el Compartimento dentro del Cambiador de CD 1. Presione el botón OPEN para abrir la puerta delantera abajo. 2. Asegurándose que la parte superior del compar timento está hacia arriba, suavemente insértelo dentro de la unidad hasta que escuche un chasquido. 3. Cierre el panel delanter ...

  • Jensen MCD10 - page 16

    16 MCD10 T roubleshooting Using the Reset Button Press RESET only when one of these conditions occur: • The compact disc changer is first installed • V ehicle power is interru pted (as when replacing the battery) Specifications Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz-20kHz (-3dB) ...

  • Jensen MCD10 - page 17

    17 MCD10 Dépannage Utilisation du Bo uton de RESET (Réglage) N'appuyez sur le bouton de RESET (Réglage) que dans les conditions suivantes: 1. Le changeur disque compact vient d'être installé. 2. La puissance du véhicule est interrompue (par exemple, lorsque vous remplacez la pi le). Caractéristiques Réponse fréquence . . . . . . ...

Produzent Jensen Kategorie Car Stereo System

Dokumente, die wir vom Produzenten des Geräts Jensen MCD10 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Jensen
- Bedienungsanleitungen MCD10
- Produktkarten Jensen
- Informationsbroschüren
- oder Energieetiketten Jensen MCD10
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Jensen MCD10.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Jensen MCD10, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Jensen MCD10. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Jensen MCD10 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Jensen MCD10, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Jensen MCD10 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Jensen MCD10 verständlich ist.

Eine gänzliche Bedienungsanleitung von Jensen sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Jensen MCD10 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Jensen MCD10 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Jensen MCD10, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Jensen MCD10 - die uns die ersten Schritte während der Nutzung von Jensen MCD10 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Jensen MCD10 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Jensen MCD10 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Jensen MCD10?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Jensen MCD10 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Jensen MCD10 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)