Deutsch dropdown-ico

Bedienungsanleitung Calculated Industries 4080

39 Seiten Betrifft nicht
Download

Zur Seite of 39

Summary
  • Calculated Industries 4080 - page 1

    C ONSTRUCTION M ASTER ® P RO Pocket Reference Guide For Models: 4065 v3.1 Construction Master Pro 4080 v3.1 Construction Master Pro T rig ...

  • Calculated Industries 4080 - page 2

    The Construction Master Pro calculators help you save time, cut costly errors and build like a pro! Quickly Solve: • Feet-Inches-Fractions, Y ards, Metric Dimensional Problems and Conversions • Problems Involving All Fractions – 1/2 through 1/64ths! • Areas, V olumes and Weights • Column/Cone Area and Volume • Blocks/Bricks, Drywall and ...

  • Calculated Industries 4080 - page 3

    KEY DEFINITIONS ..................................1 Basic Function Keys ............................1 Unit Keys .............................................2 Length, Width and Height Keys ( NOT A V AILABLE ON TRIG MODEL #4080) .......2 Circle/Arc Keys ....................................2 Construction Project Keys ................... 3 T rigonomet ...

  • Calculated Industries 4080 - page 4

    Board Feet and Cost .........................15 Circle Area and Circumference..........16 Circle/Arc Properties ..........................16 Compound Miter ................................17 Concrete Columns .............................18 Concrete Footings ( NOT A VAILABLE ON TRIG MODEL #4080) .........................19 Concrete V olume for Drive ...

  • Calculated Industries 4080 - page 5

    P OCKET R EFERENCE G UIDE — 1 Basic Function Keys + – x Arithmetic operation keys. ÷ = % Four-function (+, –, x, ÷) percent key . 0 – 9 Keys used for entering and • numbers. O Off Key — T urns all power off, clearing all non-perma- nent registers. o On/Clear Key — T urns on power . Pressing once clears the display . Pressing twice c ...

  • Calculated Industries 4080 - page 6

    P OCKET R EFERENCE G UIDE — 2 Unit Keys y Y ards f Feet i Inch / Fraction Bar m Meters Ç 7 Centimeters Ç 9 Millimeters Ç 2 Acres Length, Width and Height Keys ( NOT A VAILABLE ON TRIG MODEL #4080) l Enters length for calculation of area or volume. W Calculates area, square-up and perimeter . h Calculates volume, wall area and total room area. ...

  • Calculated Industries 4080 - page 7

    P OCKET R EFERENCE G UIDE — 3 Ç a Radius — Enters or calcu- lates circle radius. Construction Project Keys Ç l Blocks/Bricks — Finds the number of blocks or bricks for a given area and stored block/brick size. ß 4 — Stores block or brick size (default: 128 Square Inches area and 16 Inches length). Ç 8 Board Feet — Enters or converts c ...

  • Calculated Industries 4080 - page 8

    P OCKET R EFERENCE G UIDE — 4 Ç h Drywall — Calculates num- ber of 4 x 8, 4 x 9 and 4 x 12 drywall sheets based on entered or calculated area. Ç W Footing — Finds quantity of concrete, based on entered wall length and stored footing area. ß 6 — Stores footing area (default: 264 Square Inches). Ç d Roof — Calculates roof area, number o ...

  • Calculated Industries 4080 - page 9

    P OCKET R EFERENCE G UIDE — 5 T rigonometric Keys ( TRIG MODEL #4080) S Finds the sine of a degree or undimensioned value. Ç S Arcsine (sin -1 ) — Gives the angle for the Sine value. ç Finds the Cosine. Ç ç Arccosine (cos -1 ) — Gives the angle for the Cosine value. t Finds the T angent. Ç t Arctangent (tan -1 ) — Gives the angle for t ...

  • Calculated Industries 4080 - page 10

    P OCKET R EFERENCE G UIDE — 6 R Enters or calculates the horizontal leg of a right tri- angle. d Diagonal — Enters or cal- culates the Diagonal leg, or Common rafter . H Hip/V alley — Calculates length of the regular or irregular Hip/V alley rafter . Ç H Enters irregular pitch used to calculate lengths of the irregular Hip/V alley and Jack r ...

  • Calculated Industries 4080 - page 11

    P OCKET R EFERENCE G UIDE — 7 Stair Layout Key s Given rise and/or run and stored variables, calculates or displays: Press Result 1 Riser Height 2 Number of Risers 3 Riser Overage/ Underage 4 T read Width 5 Number of T reads 6 T read Overage/ Underage 7 Stairwell Opening 8 Stringer Length 9 Angle of Incline 10 Stored or Calculated Run 1 1 Stored ...

  • Calculated Industries 4080 - page 12

    P OCKET R EFERENCE G UIDE — 8 Ç s Riser Limited — Recalculates Riser Height and other stair values if you’re limited by local code. The calculated Riser Height will never exceed the stored Desired Riser Height. ST AIR DEF AULT V ALUES • 7-1/2” Desired Riser Height • 10” Desired T read Width • 10” Floor Thickness • 6’8” Head ...

  • Calculated Industries 4080 - page 13

    P OCKET R EFERENCE G UIDE — 9 Miscellaneous Functions B Backspace Key ® = Paperless T ape Ç ß Preference Settings Ç ÷ (1/x) Reciprocal Ç x Clear All Ç – (+/–) T oggle Ç + Pi ( π ) 3.141593 Ç • Converts between D:M:S and Decimal Degrees. Ç % x 2 Ç B ( ) Square Root Ç / Exponential Notation (x10 y ) Ç 0 T otal Cost (based on ent ...

  • Calculated Industries 4080 - page 14

    P OCKET R EFERENCE G UIDE — 10 ß 1 (M1) Storage Register ß 2 (M2) Storage Register ß 3 (M3) Storage Register ® ® Recall and Clear M+ ® µ , 1 , Recall M+, M1, M2 or M3 2 or 3 Entering Linear Dimensions Examples of entering Linear Dimensions: DIMENSION KEYSTROKE Clear calculator o 5 Feet 1-1/2 Inch 5 f 1 i 1 / 2 * Clear calculator o 5 Y ards ...

  • Calculated Industries 4080 - page 15

    P OCKET R EFERENCE G UIDE — 11 Entering Square/Cubic Dimensions Examples of entering Square and Cubic Dimensions: KEYSTROKE DISPLA Y o o 0. Enter numeric value and press desired unit key once to label value as “Linear:” 1 0 0 f 100 FEET KEYSTROKE DISPLA Y o o 0. Enter numeric value and press desired unit key twice to label value as “Square: ...

  • Calculated Industries 4080 - page 16

    P OCKET R EFERENCE G UIDE — 12 Adding and Subtracting Strings of Dimensions Add the following measurements: • 6 Feet 2-1/2 Inches • 1 1 Feet 5-1/4 Inches • 18.25 Inches Then subtract 2-1/8 Inches. KEYSTROKE DISPLA Y 6 f 2 i 1 / 2 + 1 1 f 5 i 1 / 4 + 1 8 • 2 5 i = 19 FEET 2 INCH – 2 i 1 / 8 = 18 FEET 1 1-7/8 INCH Rectangular Area and V o ...

  • Calculated Industries 4080 - page 17

    P OCKET R EFERENCE G UIDE — 13 Entering Square and Cubic and Adding a W aste Allowance Add a 10% waste allowance to 55 Square Feet. Then add a 20% waste allowance to 150 Cubic Feet: KEYSTROKE DISPLA Y 5 5 f f + 1 0 % 60.5 SQ FEET 1 5 0 f f f + 2 0 % 180. CU FEET Using Multi-Function h Key ( NOT A VAILABLE ON TRIG MODEL #4080) Find the volume, wal ...

  • Calculated Industries 4080 - page 18

    P OCKET R EFERENCE G UIDE — 14 Dividing Dimensions Divide 15 Feet 3-3/4 Inches into thirds (divide by 3): KEYSTROKE DISPLA Y 1 5 f 3 i 3 / 4 ÷ 3 = 5 FEET 1-1/4 INCH Linear Conversions Convert 10 Feet 6 Inches to other dimen- sions, including Metric: KEYSTROKE DISPLA Y 1 0 f 6 i 10 FEET 6 INCH Ç f * 10.5 FEET Ç i * 126. INCH Ç y 3.5 YD Ç m 3. ...

  • Calculated Industries 4080 - page 19

    P OCKET R EFERENCE G UIDE — 15 Square and Cubic Conversions Convert 14 Square Feet to Square Y ards: KEYSTROKE DISPLA Y 1 4 f f 14 SQ FEET Ç y 1.555556 SQ YD Convert 12 Cubic Feet to Cubic Y ards: KEYSTROKE DISPLA Y 1 2 f f f 12 CU FEET Ç y 0.444444 CU YD Blocks ( NOT A VAILABLE ON TRIG MODEL #4080) How many blocks (block size 8” x 16”) wil ...

  • Calculated Industries 4080 - page 20

    P OCKET R EFERENCE G UIDE — 16 KEYSTROKE DISPLA Y o o 0. 2 x 4 x 1 6 Ç 8 µ BDFT 10.66667 2 x 1 0 x 1 8 Ç 8 µ BDFT 30. 2 x 1 2 x 2 0 Ç 8 µ BDFT 40. ® ® BDFT 80.66667 x 2 7 5 Ç 0 (Cost) $22. 18 Circle Area and Circumference Find the area and circumference of a circle with a diameter of 25 Inches: KEYSTROKE DISPLA Y o o 0. 2 5 i C DIA 25 IN ...

  • Calculated Industries 4080 - page 21

    P OCKET R EFERENCE G UIDE — 17 2. Find Degree of Arc, Chord Length, Segment Area, Pie Slice Area and Segment Rise: a ARC 74.48 ° a CORD 3 FEET 0-5/16 INCH a SEG 1.051381 SQ FEET a PIE 4.0625 SQ FEET a RISE 0 FEET 6-1/8 INCH * *Y ou may also find arched segment wall stud sizes, based on the stored o.c. After the segment rise, the calculator will ...

  • Calculated Industries 4080 - page 22

    P OCKET R EFERENCE G UIDE — 18 Concrete Columns Find the total Cubic Y ards and T ons of concrete (using 1.5 tons per cu. yd) required for three (3) columns, each with a diameter of 5 Feet 2-3/4 Inches and a height of 10 Feet: KEYSTROKE DISPLA Y 1. Recall stored Weight per V olume: o o 0. ® 0 1.5 Ton Per CU YD 2. Enter diameter: 5 f 2 i 3 / 4 C ...

  • Calculated Industries 4080 - page 23

    P OCKET R EFERENCE G UIDE — 19 Concrete Footings ( NOT A V AILABLE ON TRIG MODEL #4080) Find the volume of concrete required for an 8” x 16” footing that measures 100 Feet in length: KEYSTROKE DISPLA Y o o 0. 8 i x 1 6 i = 128. SQ INCH ß 6 F-AR 128. SQ INCH 1 0 0 f Ç W (Footing) FTG 3.292181 CU YD Concrete V olume for Driveway Calculate the ...

  • Calculated Industries 4080 - page 24

    P OCKET R EFERENCE G UIDE — 20 Converting D:M:S Convert 23° 42’ 39” to decimal degrees: KEYSTROKE DISPLA Y o o 0. 2 3 • 4 2 • 3 9 DMS 23.42.39 Ç • (dms deg) 23.71° Drywall ( NOT A VAILABLE ON TRIG MODEL #4080) Find the number of 4 x 8, 4 x 9 and 4 x 12 sheets needed to cover an area of 125 Square Feet: KEYSTROKE DISPLA Y o o 0. 1 2 5 ...

  • Calculated Industries 4080 - page 25

    P OCKET R EFERENCE G UIDE — 21 KEYSTROKE DISPLA Y o o 0. 7 f 5 i Ç a (Radius) RAD 7 FEET 5 INCH 5 Ç R (Polygon) FULL 108.00° R HALF 54.00° R SIDE 8 FEET 8-5/8 INCH R PER 43 FEET 7-1/8 INCH R AREA 130.7868 SQ FEET Roofing Materials Find the roof area, number of roofing squares and bundles of shingles, stored bundles size, and number of 4 x 8 s ...

  • Calculated Industries 4080 - page 26

    P OCKET R EFERENCE G UIDE — 22 Squaring-Up a Foundation Square-up a 15’ 6” x10’ 2” foundation:* KEYSTROKE DISPLA Y o o 0. 1 5 f 6 i l LNTH 15 FEET 6 INCH 1 0 f 2 i W WDTH 10 FEET 2 INCH W W SQUP 18 FEET 6-7/16 INCH *Alternative Method, or for T rig model (#4080) Owners: Square-up a 15’ 6” x10’ 2” foundation. KEYSTROKE DISPLA Y o o ...

  • Calculated Industries 4080 - page 27

    P OCKET R EFERENCE G UIDE — 23 Studs Find the number of 16-inch On-center studs* required for a wall measuring 25 feet in length: KEYSTROKE DISPLA Y o o 0. 2 5 f Ç 5 (Studs) STUD 20. * If you are working with a number other than 16 Inches On-center , change it via ß 5 (e.g., 18 Inches o.c., enter 1 8 i ß 5 , then recalculate above). ...

  • Calculated Industries 4080 - page 28

    P OCKET R EFERENCE G UIDE — 24 Pitch — Converting Roof Angle Find the % Grade, Slope and Pitch in Inches if the roof angle is 30.25°: KEYSTROKE DISPLA Y o o 0. 3 0 • 2 5 p PTCH 30.25° p %GRD 58.31828 p SLP 0.583183 p PTCH 7 INCH Converting Slope Find the Pitch in Inches, Pitch Degrees, and Percent Grade if the slope is 0.625: KEYSTROKE DISP ...

  • Calculated Industries 4080 - page 29

    P OCKET R EFERENCE G UIDE — 25 KEYSTROKE DISPLA Y 1. Use trigonometry formula (divide the rise by the hypotenuse): o o 0. 6 f ÷ 1 0 f = 0.6 2. Solve for angle or degrees:minutes:sec- onds: Ç ç (cos -1 ) 53.13° Ç • (dms deg) DMS 53.07.48 Common Rafter Length Find the point-to-point length of the Common rafter on a 7/12-pitched roof with a s ...

  • Calculated Industries 4080 - page 30

    P OCKET R EFERENCE G UIDE — 26 Regular Hip/V alley and Jack Rafters A roof ’s Pitch is 9/12 and half the total span is 6 Feet. Find the lengths of the Common, Hip/V alley and Jack rafters. Also find the incremental jack adjustment and the cut angles. (Jack rafters at 16” On-center spacing.) KEYSTROKE DISPLA Y 1. Find the Common rafter length: ...

  • Calculated Industries 4080 - page 31

    P OCKET R EFERENCE G UIDE — 27 j JK 4 0 FEET 10 INCH j JK 5 0 FEET 0 INCH j PLMB 36.87° j LEVL 53.13° j CHK1 45.00° Irregular Hip/V alley A roof has a 9/12 Pitch, an irregular Pitch of 8/12, and half the span is 6 Feet 7 Inches. Solve the Hip/V alley length. On-center spacing is 16 Inches. KEYSTROKE DISPLA Y 1. Find Common rafter length: o o 0 ...

  • Calculated Industries 4080 - page 32

    P OCKET R EFERENCE G UIDE — 28 Rake-W all – No Base Find each stud size in a Rake-Wall with a peak of 3 Feet 6 Inches, and a length of 5 Feet. Use 16 Inches as your On-center spacing (default; already stored): KEYSTROKE DISPLA Y 1. Enter Rise and Run: o o 0. 3 f 6 i r RISE 3 FEET 6 INCH 5 f R RUN 5 FEET 0 INCH 2. Find stud lengths: Ç r (R/Wall ...

  • Calculated Industries 4080 - page 33

    P OCKET R EFERENCE G UIDE — 29 Rake-W all – With Base Find each stud size in a Rake-Wall with a peak of 4 Feet, a length of 8 Feet, and a base of 5 Feet. Use 16 Inches as your On-center spacing: KEYSTROKE DISPLA Y 1. Enter Rise and Run: o o 0. 4 f r RISE 4 FEET 0 INCH 8 f R RUN 8 FEET 0 INCH 2. Enter base and find stud lengths and angle of incl ...

  • Calculated Industries 4080 - page 34

    P OCKET R EFERENCE G UIDE — 30 Stairs — Given Rise and Run Y ou’re going to build a stairway that has a floor-to-floor height of 10 Feet 1 Inch, a run of 12 Feet 5 Inches, and a desired riser height of 7-1/2 Inches (default). Find the stair values: KEYSTROKE DISPLA Y 1. Enter rise and run: o o 0. 1 0 f 1 i r RISE 10 FEET 1 INCH 1 2 f 5 i R RU ...

  • Calculated Industries 4080 - page 35

    P OCKET R EFERENCE G UIDE — 31 Stairs — Given Rise Only Y ou’re building a stairway with a total rise of 9 Feet 1 1 Inches. Using the default riser height of 7-1/2 Inches and tread width of 10 Inches, find the stair values: KEYSTROKE DISPLA Y 1. Enter known Rise: o o 0. 9 f 1 1 i r RISE 9 FEET 1 1 INCH 2. Recall stored desired stair riser hei ...

  • Calculated Industries 4080 - page 36

    P OCKET R EFERENCE G UIDE — 32 Stairs — Riser Limited Function Calculate stairs using the Riser Limited function, if you must limit the Riser Size to 7-1/2 Inches: KEYSTROKE DISPLA Y 1. Enter Rise and Run: o o 0. 1 0 f 1 i r RISE 10 FEET 1 INCH 1 2 f 5 i R RUN 12 FEET 5 INCH 2. Recall stored 7-1/2” Desired Riser height and find stair values: ...

  • Calculated Industries 4080 - page 37

    P OCKET R EFERENCE G UIDE — 33 After a Clear All ( Ç x ), your calculator will return to the following settings: STORED V ALUES DEF AUL T V ALUE Desired Riser Height 7-1/2 INCH Desired T read Width 10 INCH Floor Height 10 INCH On-center Spacing 16 INCH Weight per V olume 1.5 Ton Per CU YD Block Area (except T rig model) 128. SQ INCH Block Length ...

  • Calculated Industries 4080 - page 38

    P OCKET R EFERENCE G UIDE — 34 (Cont’d) PREFERENCE SETTINGS DEF AULT V ALUE Stairway Headroom 6 feet 8 inch Rake-W all Descending Arched W all Outside Jack Rafters Descending Irregular Jack Spacing OC-OC Exponent Off Meter Linear Display 0.000 Decimal Degree Display 0.00° Fractional Mode Standard *Depressing the Reset button located above the ...

  • Calculated Industries 4080 - page 39

    This equipment has been certified to comply with the limits for a Class B computing device, pursuant to Subpart J of Part 15 of FCC rules. Software copyrighted and licensed to Calculated Industries, Inc. by Construction Master T echnologies, LLC, 2006. Pocket Reference Guide copyrighted by Calculated Industries, Inc. © 2006. Construction Master® ...

Produzent Calculated Industries Kategorie Calculator

Dokumente, die wir vom Produzenten des Geräts Calculated Industries 4080 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Calculated Industries
- Bedienungsanleitungen 4080
- Produktkarten Calculated Industries
- Informationsbroschüren
- oder Energieetiketten Calculated Industries 4080
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Calculated Industries 4080.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Calculated Industries 4080, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Calculated Industries 4080. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Calculated Industries 4080 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Calculated Industries 4080, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Calculated Industries 4080 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Calculated Industries 4080 verständlich ist.

Eine gänzliche Bedienungsanleitung von Calculated Industries sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Calculated Industries 4080 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Calculated Industries 4080 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Calculated Industries 4080, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Calculated Industries 4080 - die uns die ersten Schritte während der Nutzung von Calculated Industries 4080 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Calculated Industries 4080 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Calculated Industries 4080 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Calculated Industries 4080?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Calculated Industries 4080 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Calculated Industries 4080 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)