-
Pelco IS310-CW - page 1
INST ALLA TION C3429M-A (1/08) IS310 Series Camclosure ® Integrated Camera Sy stem ...
-
Pelco IS310-CW - page 2
2 C3429M-A (1/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...
-
Pelco IS310-CW - page 3
C3429M-A (1/08) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...
-
Pelco IS310-CW - page 4
4 C3429M-A (1/08) Description The 310 Series Camclosure ® integrated camera system is a track-light design that mounts to a wall or ceiling. The system incorporates a camera and lens p ackage into a small, unobstructive, medium-security enclosure designed for areas subject to vandalism. The system is quick and easy to install in a variety of indoo ...
-
Pelco IS310-CW - page 5
C3429M-A (1/08) 5 Installation PREPARE WALL OR CEILING Prepare the wall or ceiling accordin g to one of the following options. • Mounting directly to wall or ceiling Figure 1. W all/Ceiling Mounting • Mounting to a 4S electrical box with 404 plaster ring Figure 2. Mounting to a 4S Electrical Box • Mounting to ICS310-COND conduit adapter (not ...
-
Pelco IS310-CW - page 6
6 C3429M-A (1/08) • Mounting to a 2-gang electrical box Figure 4. Mounting to a 2-Gang Electrical Box CONNECT VIDEO AND POWER 1. Some indoor installations do not require a heater . If the installation does not require a heater , disconnect the heater wiring. a. Remove the cover with the supplied 1/8-inch hollow screwdriver bit. b. Remove the came ...
-
Pelco IS310-CW - page 7
C3429M-A (1/08) 7 Figure 5. Exploded Parts View Figure 6. Camera Mounting Holes ATTACH BASE 1. Release the base locking ring for access to the mo unting holes. 2. Attach the base to an adapter plate or conduit adapter using the two 6-32 x 1.25-inch tamper-resistant screws supplied with the adapters. Use the 1/8-inch hollow screwdriver bit supplied ...
-
Pelco IS310-CW - page 8
8 C3429M-A (1/08) ADJUST ENCLOSURE 1. T urn on power to the camera and monitor . 2. Release one or both locking rings, and swivel the enclosure until the angle of the camera is correct (refer to Figure 7). 3. T ighten the locking rings. Figure 7. Adjusting Enclosure Position 4. If you have a varifocal lens, remove the cover with the supplied 1/8-in ...
-
Pelco IS310-CW - page 9
C3429M-A (1/08) 9 DN/CH SERIES ADJUSTMENTS Refer to Figure 9 to adjust the IS310-DN or IS310-CH model. Figure 9. Adjusting the IS310-DN/CH Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Auto Gain Control The automatic gain control (AGC) adjusts the imag e autom atically to compensate for ...
-
Pelco IS310-CW - page 10
10 C3429M-A (1/08) Set to SW4-4 ON to enable flickerless operation. The camera will remove the effects of flickering and the shutter speed will be set to 1/120 (NTSC) or 1/100 (P AL). Set to SW4-4 OFF to disable flickerle ss operation. This is the default setting. NOTE: If you enable flickerless operation, you should use AC line lock for best resul ...
-
Pelco IS310-CW - page 11
C3429M-A (1/08) 11 Adjusting V ertical Phase Y ou may need two people when synchronizing the cameras: one at the camera, the other at the monitor to observe the vertical roll and the effect of any camera adjustments. T o synchronize the cameras: 1. Choose a reference camera to which all other cameras will be phased. 2. Select the camera to synchron ...
-
Pelco IS310-CW - page 12
12 C3429M-A (1/08) DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view , l ...
-
Pelco IS310-CW - page 13
C3429M-A (1/08) 13 DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 11 to adjust the IS310-DW or IS310-CW model. Figure 11. Adjusting the IS310-DW/C W Series Camclosure SWITCH SETTINGS Locate the DIP switch and then set the switches for your installation. SW1-1: Video Format Set SW1-1 to ON for NTSC. Set it to OFF for P AL. The default ...
-
Pelco IS310-CW - page 14
14 C3429M-A (1/08) SW1-4: Auto White Balance/Ma nual White Balance Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video is all white. 3. While holding the background in place, set SW1-4 to OFF . A green block and a white ...
-
Pelco IS310-CW - page 15
C3429M-A (1/08) 15 SW1-8: Day/Night Operation (DW models onl y) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the general light levels at which th ...
-
Pelco IS310-CW - page 16
16 C3429M-A (1/08) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS310-DW and IS 310-CW Series Camclosures automatic ally adjust the camera to the auto iris. Auto iris level adjustments are not necessary. V ERTICAL PHASE ADJUSTMENT NOTES: • Use this procedure for 24 VAC operation only . • When adjusting vertical phase, line sync (SW1 -2) mu ...
-
Pelco IS310-CW - page 17
C3429M-A (1/08) 17 Service Connector The IS310 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the field of view and focus the camera. Figure 1 3. Service Connector Pelco offers two optional items that plug directly into the service connector: CST150 compac ...
-
Pelco IS310-CW - page 18
18 C3429M-A (1/08) Specifications General Pan/T ilt Adjustment Manual Pan 180° T ilt 180° Construction Aluminum base and cover , steel camera mounting bracket Finish Gray polyester powder coa t Environment Low temperature, indoor/ou tdoor Operating T emperature -50° to 122°F (-46° to 50°C); de-ices to -10°F (-23°C) Heater T urns on at 50°F ...
-
Pelco IS310-CW - page 19
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warranty are as noted below: • Five years on fiber opt ic products and TW3 000 Series unshield ed twisted pair (UTP) ...
-
Pelco IS310-CW - page 20
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab E ...
Haben Sie eine Frage bezüglich Pelco IS310-CW?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco IS310-CW nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco IS310-CW hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.