-
Yamaha EMX 2000 - page 1
E Owner’s Manual 10 0 PEAK +8 +5 +3 +1 0 –1 –3 –5 –7 –10 –15 –20 GRAPHIC EQUALIZER DIGITAL EFFECT 6 0 6 MAX MIN PROGRAM PHANTOM (+48V) PHONES/C.R.OUT 10 0 ST 2 10 0 ST MONO BRIDGE POWER AMP TAPE IN LIMITER LR MONO +4dB FOOT SW MONI MONI (MONO) PAMP IN 2 EFFECT +4dB PHONES/ C-R OUT (+4dB) LEVEL L/BRIDGE ST L MONI 1 ST R MONO 10 0 +4 ...
-
Yamaha EMX 2000 - page 2
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessori ...
-
Yamaha EMX 2000 - page 3
2 EMX2000—Owner’s Manual Introduction Thank you for pur chasing the Y amaha EMX2000 P owered M ix er . In order t o take full advantage of the EMX2000 and enjoy long, trouble-fr ee performance, please read this owner’ s manual carefully , and keep it in a safe place for future r eferenc e. Features • The EMX2000 pro vides versatile inputs, ...
-
Yamaha EMX 2000 - page 4
3 EMX2000—Owner’s Manual Precautions 1. A void excessive heat, humidity , dust and vibration K eep the unit away fr om locations where it is likely t o be exposed to high temperatures or humidity — such as near radiators, stov es, etc. Also av oid locations which ar e subject to ex ces- siv e dust accumulation or vibration which could cause m ...
-
Yamaha EMX 2000 - page 5
4 EMX2000—Owner’s Manual Front and rear panel Control panel ■ Channel control section In this section, you can adjust equalization (fre- quency response), volume level, effect and moni- tor output levels for the input signal of eac h channel. 1 GAIN control U se this knob to adjust the sensitivit y ac cor ding to the input signal level, so th ...
-
Yamaha EMX 2000 - page 6
5 EMX2000—Owner’s Manual 6 Effect control (EFFECT) For eac h channel, this contr ols the amount of sig- nal that is sent to the EFFECT bus. The signal of the EFFECT bus is sent to the EFFECT jack (input/output panel A ). It is also sent to the built-in effect when the ON switch P in the EFFECT section is turned on. 7 P AN (panpot) control (Chan ...
-
Yamaha EMX 2000 - page 7
6 EMX2000—Owner’s Manual ■ Master control section In this section, you can adjust the final level of the outputs. E MONI 1 (monitor 1) fader The MONI 1 fader adjusts the final level of the signal sent from the MONIT OR 1 bus to the MONI 1 jack (input/output panel 9 ). If the P ower amp select switch V is set to MONI 1- MONO , using this fad ...
-
Yamaha EMX 2000 - page 8
7 EMX2000—Owner’s Manual ■ Digital effect section This section enables you t o turn the built-in digi- tal effect on/off and select the effect type. M MONI 1/2 (monitor 1/2) control This knob adjusts the level of the r eturn signal that is sent from the built-in digital effect to the MONIT OR 1/2 buses. N ST (stereo) control This knob adjusts ...
-
Yamaha EMX 2000 - page 9
8 EMX2000—Owner’s Manual U LEVEL controls These knobs enable you t o adjust the level of the signals input from the mix er section to the po wer amp section. Rotating the knob clockwise will raise the level of the input signal. U se a screw- driver of a w idth of 3mm or less to adjust the knob . If an external piece of equipment is c onnected t ...
-
Yamaha EMX 2000 - page 10
9 EMX2000—Owner’s Manual Input/output panel 1 Channel input jacks (MIC, LINE) 1~8 These are the input jacks for channels 1~8. By using the GAIN co ntrol (contr ol panel 1 ) you can c onnect an y of the jacks t o a wide r ange of sour ces, from mics to line-level devices (including synthesizers and rh y thm mac hines). The MIC jacks can pro vide ...
-
Yamaha EMX 2000 - page 11
10 EMX2000—Owner’s Manual 3 Channel input jacks 9~12A Channel input jacks 9~12B These are the input jacks for channels 9/10~11/12 and are used to c onnect to the st ereo output jacks of electr onic instruments, cassette decks, or CD play ers. U se the A/B switch (control panel 2 ) to select phone jacks (A) or phono jacks (B). The nominal input ...
-
Yamaha EMX 2000 - page 12
11 EMX2000—Owner’s Manual Rear panel 1 SPEAKERS (speaker output) jacks Speakers can be c onnected t o these jacks. The ty pe of sig nals output, the number of speak- ers you can c onnect, and acc eptable impedance differ depending on the setting of the P ower amp select switch (contr ol panel V ). • When the Power amp select switch is set to ...
-
Yamaha EMX 2000 - page 13
12 EMX2000—Owner’s Manual Connections W hen connecting various devices, be sur e to use cables and plugs of the appr opriate standard. Connecting speakers There ar e three wa ys in which speakers can be c onnected t o the EMX2000. 1 Connecting a single speaker to each of the L and R jacks: A single speaker each can be c onnected to either jack ...
-
Yamaha EMX 2000 - page 14
13 EMX2000—Owner’s Manual Basic operation Connecting microphones and instruments 1 Before connecting mics or instruments, make sure that the power of all equip- ment (where applicable) is turned off. Also make sure that each channel fader and the faders in the master section are turned down. Check to see if the Power amp select switch on the co ...
-
Yamaha EMX 2000 - page 15
14 EMX2000—Owner’s Manual Example setups This section pro vides some ways in which the EMX2000 can be used, and explains c onnections and operation. As a band P A Her e is an example of using the EMX2000 as a small P A for a band. In this example, the monitor speakers ar e being sent a mix that is independent of the MAIN speak er mix. An extern ...
-
Yamaha EMX 2000 - page 16
15 EMX2000—Owner’s Manual As a conference/entertainment hall sound system Her e is an example of using the EMX2000 as a conference or ent ertainment hall sound system. ■ Connections • Connect mics t o channel inputs 1~8. • A CD pla yer/LD pla yer/cassett e deck can also be connect ed to the input jacks of channels 9/10 and 11/12. • T o ...
-
Yamaha EMX 2000 - page 17
16 EMX2000—Owner’s Manual ■ Sending an independent mix to the monitor speakers 1 Set the MONI 1 or MONI 2 fader to the “ 10 ” position. 2 Raise the MONI 1 or MONI 2 controls for the channels that you wish to hear from the monitor speakers. 3 Use the MONI 1 or MONI 2 fader of the master section to adjust the overall vol- ume. ■ Using an ...
-
Yamaha EMX 2000 - page 18
17 EMX2000—Owner’s Manual Speci fi cations ■ General speci fi cations Maximum output po wer STEREO: 200 W+200 W/4 Ω @0.5% THD at 1 kHz BRIDGE: 400 W/8 Ω @0.5% THD at 1 kHz Frequency response 20 Hz~20 kHz +1 dB, – 3 dB @1 W output into 8 Ω (SPEAKER OUT) All channel Gain controls at minimum. 20 Hz~20 kHz +1 dB, – 3 dB @+4 dB output ...
-
Yamaha EMX 2000 - page 19
18 EMX2000—Owner’s Manual ■ Input speci fi cations ■ Output speci fi cations Specifications are subject to c hange without pr ior notic e. 1. Sensiti vity is the lo west le vel that can produce an output of +4 dB (1.23 V) or the nominal output le v el when the unit is set at maximum gain. 2. XLR type connectors and PHONE J A CKS (TRS) (T ...
-
Yamaha EMX 2000 - page 20
19 EMX2000—Owner’s Manual Dimensions Unit: mm 167.6 W: 480 D: 454 H: 125 277.7 ...
-
Yamaha EMX 2000 - page 21
20 EMX2000—Owner’s Manual Block/Level Diagram PAN PAN MONI 1,MONO PFL 0 dB dB MONI 1 MONI 2 MONI 1 MONI 2 P AMP L P AMP R MONI 1 MONO PHONES (3mW/40 Ω ) ST, MONO, MONITOR, EFFECT, C.R.OUT, P AMP IN (+4dB) PHONES/C.R.OUT EFFECT C.R.MONITOR L, R BRIDGE 16 15 14 3 2 1 (MIN MAX) P AMP IN L/BRIDGE GRAPHIC EQUALIZER REC OUT ( – 10dBV) CH INS I/O ...
-
Yamaha EMX 2000 - page 22
Y AMAHA CORPORA TION VZ42360 R1 1 IP 24 Pro Audio Division, #18/3 P .O. Box 3, Hamamatsu, 430-8651, J apan NP Printed in T aiwan ...
Haben Sie eine Frage bezüglich Yamaha EMX 2000?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Yamaha EMX 2000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Yamaha EMX 2000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.