Bedienungsanleitung Humminbird LCR 400 ID

28 Seiten 0.37 mb
Download

Zur Seite of 28

Summary
  • Humminbird LCR 400 ID - page 1

    ...

  • Humminbird LCR 400 ID - page 2

    TABLE OF CONTE NTS I NSTALLATION PREPARATION ……………………………………………………… . 2 Parts Supplied ………………………………………………………………… …. 2 Accessories …………………………………………………………………… …. 2 Installation Overview ………………? ...

  • Humminbird LCR 400 ID - page 3

    TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the following before in stalling your transducer. TRANSDUCER MOUNTING OPTIONS A. Transom Mount - The Humminbird hig ...

  • Humminbird LCR 400 ID - page 4

    absorb the blow of any obstruction by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it b ack in place. (See Figure A) B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot assemb ...

  • Humminbird LCR 400 ID - page 5

    aluminum boat locate the template on the transom between rows of rivets, or ribs that are on the bottom of the boat. Align the template so that the bottom corner of the template nearest the center of the transom is on the bottom edge of the transom. Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Atta ...

  • Humminbird LCR 400 ID - page 6

    NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied. Be sure to align the holes so that they are c ...

  • Humminbird LCR 400 ID - page 7

    Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the headed pin and insert it through th e two parts. Assemble by screwing the ¼”x3/8” allen head screw into the end of the pin a ...

  • Humminbird LCR 400 ID - page 8

    using the 5/32” allen wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot. (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the b ...

  • Humminbird LCR 400 ID - page 9

    4. Put transducer in the water. The bottom of the transducer should be in a flat area and should be in good contact with the bottom of the boat. 5. Operate the LCR with the boat operating at high speed. The transducer may have t o be moved in order to find an area where satisfactory operation is observed. 6. When an area is found that produces sati ...

  • Humminbird LCR 400 ID - page 10

    INSTALLING THE LCR The LCR should be mounted on a flat, solid surface for maximum stability. The low profile swivel mount has four holes drilled in the base. It is recommended that all four holes be used. Position the swivel base and drill four ¼” diameter holes. Note: The LCR hole pattern Is the same as for all Humminbird flasher units. Use har ...

  • Humminbird LCR 400 ID - page 11

    OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommended since the unit cannot be rotated. INSTALLING THE CABLES Your LCR comes equipped with Humminbird’s ne ...

  • Humminbird LCR 400 ID - page 12

    “Transducer”. Note: An adapter (AD - 4) is available to allow use of an old waterproof (BNC) transducer with the LCR, but be sure that the transducer is a 16degree. A 32 - degree transducer cannot be used. A 11/8” hole must be drilled to pull thr ough the transducer connector. After drilling the hole, pull the transducer connector up through ...

  • Humminbird LCR 400 ID - page 13

    you will install on the transom or inside the hull, and the LCR 400ID unit which you will m ount with the supplied gimbal bracket. The transducer and LCR 400ID communicate by means of a cable, and are powered by your boat’s 12 - volt DC battery. The transducer and LCR 400ID use the basic principles of sonar to reveal objects beneath the water&apo ...

  • Humminbird LCR 400 ID - page 14

    BEFORE BEGINNING THE HUMMINBIRD ADVANTAGE T HE H UMMINBIRD A DVANTAGE The LCR 400ID incorporates the best of available technologies, and offe rs advantages you won’t find in other depth sounders. The liquid crystal display (LCD) offers sharp viewing even in bright, direct sunlight, and is continuously lit for nighttime operation. Advanced LCD “ ...

  • Humminbird LCR 400 ID - page 15

    USING THE LCR400ID USING THE BUILT - IN SIMULATOR USING THE LCR400ID This section provides co mplete information on operating the LCR 400ID through its front panel controls. You are encouraged to read this information completely as you first learn to use the LCR 400ID. Doing so will ensure you make the most of its many features and functions. The f ...

  • Humminbird LCR 400 ID - page 16

    USING THE LCR400ID OPERATING THE LCR4 00ID FRONT PANEL BUTTONS The LCR 400ID offers several functions that you can adjust with the front panel buttons. (Note that to select something with a button, you must press it fully so that you hear a “chirp” sound). You can get acquainted with these features by actual operation, or when using the simulat ...

  • Humminbird LCR 400 ID - page 17

    USING THE LCR400ID OPERATING THE LCR400ID SENSITIVI TY 1. Selecting Sensitivity/Units; Factory setting: +0/FEET The Sensitivity/Units function has two uses: It lets you adjust LCR 400ID sensitivity and controls whether depth measurement is in feet or fathoms. The LCR 400ID automatically increases or decre ases its sensitivity setting when water con ...

  • Humminbird LCR 400 ID - page 18

    USING THE LCR400ID OPERATING THE LCR400ID FISH ALARM 3. Enabling Fish Alarm; Factory Setting: OFF The Fish Alarm alerts you with a chirping sound whenever the LCR 400ID detects fish (or another object not attached to the bottom ). To activate it, select FISH ALM and press the ON - OFF button. A fish symbol reminds you that the alarm is on. ZOOM 4. ...

  • Humminbird LCR 400 ID - page 19

    USING THE LCR400ID OPER ATING THE LCR400ID BOTTOM LOCK 5. Using Bottom - Lock; Factory Setting: OFF Bottom - lock provides an up - close view like Zoom, except that in this case the zoomed view automatically moves up or down to stay on the bottom. To use this feature, select BTM LOCK and press ON - OFF. The range of the display is shown when Bottom ...

  • Humminbird LCR 400 ID - page 20

    USING THE LCR400ID OPERATING THE LCR400ID DEPTH RANGE 7. Setting Depth Range; Factory Setting: On (Automatic) When you turn the LCR 400ID on, it finds the bottom, sets the ideal depth range, and automati cally adjusts the depth range (to as much as 480’) as the depth changes. In this “Auto Depth Range” mode, the bottom is blacked - in for eas ...

  • Humminbird LCR 400 ID - page 21

    SPECIFICATIONS Operating Frequency 200 KHz Power Requirements 10 - 16 Volts Power Cable Length Standard Unit 48” Port able Unit Non - replaceable Transducer : Standard XHS - 6 - 16 Portable XPT - 6 - 16 Transducer Cone Angle 16 degrees Depth Ranges 0 to 15’, 30’, 60’, 120’, 180’, 240’, 360’, or 480’ (plus 0 - 600’ in manual mode ...

  • Humminbird LCR 400 ID - page 22

    MAINTENANCE AND WARRANTY MAINTENANCE MAINTENANCE Your Humminbird fishfinder is designed to provide years of trouble free operation with virtually no maintenance. Follow these simple procedures to ensure your Humminbird continues to deliver top performance. • If the unit comes into contact with salt spray simply wipe the affected surfaces with a c ...

  • Humminbird LCR 400 ID - page 23

    MAINTENANCE AND WARRANTY TROUBLESHOOTING TROUBLESHOOTING Do not attempt to repair the fishfinder yourself. There are no user serviceable parts inside, and special tools and techniques are required for reassembly to ensure the waterproof integrity of the housing. Repairs should be performed only by authorized Humminbird technicians. Many requests fo ...

  • Humminbird LCR 400 ID - page 24

    MAINTENANCE AN D WARRANTY TROUBLESHOOTING Second, inspect the transducer cable from end to end for breaks, kinks, or cuts in the outer casing of the cable. Also ensure the transducer is fully submerged in water. If the transducer is connected to the unit through a switc h, temporarily connect it directly to the unit and try again. If none of these ...

  • Humminbird LCR 400 ID - page 25

    MAINTENANCE AND WARRANTY TROUBLESHOOTING 5. The unit comes on before I press POWER, and won't turn off. Check the transducer cable. If the outer jacket of the cable has been cut and the cable is in contact with bare metal, you need to repair the cut with electrical tape. If there is no problem with the cable, disconnect the transducer from the ...

  • Humminbird LCR 400 ID - page 26

    MAINTENANCE AND WARRANTY WARRANTY HUMMINBIRD ONE YEAR FULL WARRANTY First year repairs (from original date of purchase) on your Humminbird fishfinder are ab solutely free. This does not include physical damage to the unit or its accessory items. Any modification or attempt to repair the original equipment or accessories by unauthorized individuals ...

  • Humminbird LCR 400 ID - page 27

    MAINTENANCE AND WARRANTY SERVICE POLICY SERVICE POLICY This Service Policy is valid in the United States only. This applies to Humminbird units returned to our facto ry in Eufaula, Alabama, and is subject to change without notice. All repair work is performed by factory - trained technicians to meet exacting factory specifications. Factory serviced ...

  • Humminbird LCR 400 ID - page 28

    MAINTENANCE AND WARRANTY CUSTOMER SUPPORT CUSTOMER SUPPORT If you have any questions, call our Humminbird Customer Suppor t Hotline: 1 - 334 - 687 - 0503 Throughout the U.S. and Canada, hours are Monday - Friday, 8:00 a.m. to 5:00 p.m. Central time. If after reading “Troubleshooting” you determine your unit needs factory service, please attach ...

Produzent Humminbird Kategorie Fish Finder

Dokumente, die wir vom Produzenten des Geräts Humminbird LCR 400 ID erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Humminbird
- Bedienungsanleitungen LCR 400 ID
- Produktkarten Humminbird
- Informationsbroschüren
- oder Energieetiketten Humminbird LCR 400 ID
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Humminbird LCR 400 ID.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Humminbird LCR 400 ID, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Humminbird LCR 400 ID. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Humminbird LCR 400 ID ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Humminbird LCR 400 ID, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Humminbird LCR 400 ID hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Humminbird LCR 400 ID verständlich ist.

Eine gänzliche Bedienungsanleitung von Humminbird sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Humminbird LCR 400 ID bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Humminbird LCR 400 ID befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Humminbird LCR 400 ID, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Humminbird LCR 400 ID - die uns die ersten Schritte während der Nutzung von Humminbird LCR 400 ID erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Humminbird LCR 400 ID hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Humminbird LCR 400 ID im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Humminbird LCR 400 ID?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Humminbird LCR 400 ID nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Humminbird LCR 400 ID hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)