Bedienungsanleitung Locke RS-5100

32 Seiten 2.41 mb
Download

Zur Seite of 32

Summary
  • Locke RS-5100 - page 1

    Reel and Bedknife Sharpener RS-5100 Operators Manual Locke T urf 307 Highway 52E Opp, Al abama 36467 (334) 493-1300 ...

  • Locke RS-5100 - page 2

    CONGRA TULA TIONS Y ou have invested in the best implemen t of its type on the market today . The care you give your Locke T urf implement will greatly determine your satisfaction with it s performance and it s service life. W e urge a careful study of this manual to provide you with a thorough understanding of you new implement before operating, a ...

  • Locke RS-5100 - page 3

    REEL & BEDKNIFE SHARPENER Operator ’ s Manual T able of Content s SECTION Dealer Preparation Check List 3 Sharpening Bedknives 20 Getting Acquainted with Your Sharpene r 4 Bedknife Grinding Angles 22 Safety 5 Maintenance and Lubrication 24 Federal Laws and Regulations 7 Servicing the Stones 25 Assembly and Setup Instructions 8 Dressing the St ...

  • Locke RS-5100 - page 4

    INTRODUCTION More than merely devices created fo r mowing grass, the excellence of design, construction and operation of Locke power mowers is unp aral- leled. Introduced in 1928, tested an d proven, Locke power mowers may be considered, in terms of today’ s te chnology , the ultimate response to the need for the highest degree of qua lity lawn c ...

  • Locke RS-5100 - page 5

    DEALER PREP ARA TION CHECK LIST REEL and BEDKNIFE SHARPENER BEFORE DELIVERING MACHINE- The foll owing check list should be completed. Use the Operator ’ s Man- ual as a guide.  1. Assembly completed.  2. Gearbox filled with oil.  3. All fittings lubricated.  4. All shields in place and in good condition.  5. All fasteners torqued t ...

  • Locke RS-5100 - page 6

    Safe ty Fi rst! Locke Turf employees are fully a ware of the need for safe operating procedures aro und all of our equipment. We hope that you will make a sincer e effort to put safety above all other prioritie s. T he Reel and Bed- knife Sharpener requir es an e xtra sp ecia l There are some features t hat have been incorporate d into this unit th ...

  • Locke RS-5100 - page 7

    Important Safety Information For your safety and to help in developin g a better un- derstanding of your equipm en t, we highly recom- mended that you read the op erator’s ma nua l. Reading these sections not only prov ides valuable trai ning but also familiarizes you with helpful information and its location. The parts sections are for reference ...

  • Locke RS-5100 - page 8

    4. DO NOT ROTATE THE REEL BY GRA SPING THE BLADES WITH YOUR BA RE H AND. THIS COULD RESULT IN SERIOUS INJURY TO YOUR FINGERS OR HAND. 5. Be sure to check the clearance of the reel and/or bedkinfe before begin nin g the grinding operation. Too much “in-feed” will cause the stone to gr ag- ment or shatter. 6. Insure that the new grinding wheel is ...

  • Locke RS-5100 - page 9

    IMPORT ANT FEDERAL LA WS AN D REGULA TIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERA TIONS. *(This section is intended to explai n in broad terms the concept and effect of the follo wing federal laws and regula- tions. It is not intended as a legal interpretation of the la ws and should not be consider ed as such.) U.S. Public Law 91-596 (The Will ...

  • Locke RS-5100 - page 10

    Uncrating the Sharpener Refer to Figures 2-1 and 2-2: 1. First, remove the eight (8) bolts securing he sharp- ener to the pallet. Fig. 2-1 (#1) 2. Using a fork lift, narrow the forks so they slide un- der the drain pan from the rear. Be careful to avoid hoses and electrical co mponents. Make sure that the forks do not slide all the way up to the ba ...

  • Locke RS-5100 - page 11

    9 1 3 4 5 2 Figure 2-1 Figure 2-2 ...

  • Locke RS-5100 - page 12

    Wiring The 5100 Sharpener THIS SHOULD BE DONE BY AN EXPERI- ENCED, LICENSED EL ECTRICIAN. Wire the sharpener to a 20 amp, 220 volt breaker equipped with a di sconnect. The elec- trical junction box is located in the upper center area inside the front panel. IMPORTANT Disconnect all power during routine mainte- nance and when the sharpener will be o ...

  • Locke RS-5100 - page 13

    Electrical Wiring Source To Front Panel Models—240 volts (Foreign) 1. Unfasten the front panel on cont rol box and s wing the do or open. 2. Locate the disconnect. It is the black pl astic switch located on the top center of the box. 3. Remove screw A and slip off the cover. 4. Connect a 0V lead to the neutral pos it ion and the 240V lead to the ...

  • Locke RS-5100 - page 14

    Overview— The RS 5100 is the latest dev elopment in the family of reel and bedknife sharpeners manufac- tured by Locke Turf. Incorporating the dual wheel head, which is an exclu- sive and unique feature of the Locke Turf sharpeners, we now offer a 6” diameter grinding stone for sharpe n- ing and grinding reels. The RS 5100 is a complete grindi ...

  • Locke RS-5100 - page 15

    Spin Grinding NOTE When discussing spin grinding, any reference to the carriage or its associated parts me ans the reel carriage, located to the righ t as viewed for the operator’s side. 1. Open front canopy and adjust wheel head a way form work table bars by turning infeed screw hand wheel coun ter clockwise, bri nging wheel he ad towards operat ...

  • Locke RS-5100 - page 16

    6. Manually move grinding carr iage left and right making sure there is ample clearance bet ween the stone and the end of the reel bla des. (It may be necessary to reposition the reel unit slig htl y.) When satisfied that the grinding wheel clears the reel unit at both ends, tighten the brackets. Figure 3-5. There are two ways to make reel a djustm ...

  • Locke RS-5100 - page 17

    Now attach the drive coupler from the spin motor to the reel. In most cases, town wobble extensions work w ell. Figure 3-8 Be sure the extension is as straight as possible. Ad- justing the spin motor on it s bracket may be necessary. Good alignment eliminates driv e lin e chatter. Figure 3- 9 NOTE The spin motor shaft must be removed and in- stalle ...

  • Locke RS-5100 - page 18

    REEL DIAMETER REV/MIN DIAL READING 4 375 10.00 5 300 7.70 6 250 6.25 7 215 5.40 8 190 4.75 9 170 4.30 10 150 3.80 RPM Setting Figure 3-11 13. Start the wheel head. PROLONGED CONTACT BETWEEN THE STONE AND REEL MA Y C AUSE THE STONE TO CHIP OR BREAK APART, CAUSING SERIOUS INJURY TO THE OPERATOR. DAMAGE TO THE REEL MAY ALSO RESULT. 14. With the carria ...

  • Locke RS-5100 - page 19

    Left The total amount of “in-f eed” can be pr e-selected from 2 to 35 teeth (0.002 to 0.035 inch), by setting the knock-off arm located directly behind the ratchet wheel. In-feeding stops automatically when the knock-off arm has rotated around and make s contact with the ratchet “pawl.” Figure 3-13 Manual Relief Grinding 1. Remove the drive ...

  • Locke RS-5100 - page 20

    7. Starting at the end of a reel blade, carefull y move the wheel head in toward the blade. Take extreme care that the blade you are gri nding is placed firmly on the finger guide slope. At this point, do not let the grinding stone make contact with the blade. Check for clearance bet ween the “next blade” and the grindin g wheel. Figure 3-15 8. ...

  • Locke RS-5100 - page 21

    25° AVG. 45° MAX. 10° MIN. Grinding Relief Angles on Reels Grinding the Angles Relief grinding should b e “tailored” to suit the applica- tion of the reel mower. T he angle of the grind should be sufficient to last for a full season of use before nor- mal wear completely removes all the relief. For exam- ple, a mower being used on Kentuck y ...

  • Locke RS-5100 - page 22

    Sharpening Bedknives 1. Install tool bar assembly on work table. Mount the bedbar with “leading edge” or “front face” of bed- knife up on the tool bar and tighten the “L” br acket clamping bolts. Figure 3-18 NOTE The two (2) location brackets can be re loc ated along the toolbar to accommodate bed bars of varying l ength. 2. Make sure t ...

  • Locke RS-5100 - page 23

    4. The cupped grindi ng stone should not extend be- yond the guard. Adjust the wheel head vertically on the pedestal mount so the inside edge of the cupped grinding stone is slightl y below the top edge of the bedknife. This will insure an ev en wear pattern on the grinding face of the stone. Figure 3-22 INJURY COULD OCCUR TO THE OPERA- TOR IF THE ...

  • Locke RS-5100 - page 24

    Grinding Relief Angles on Bedknives A shallow relief angle of 10 de grees to 15 degrees would more than likely last o n golf cours e fairway turf for and entire season (3 to 6 months) but on l y a week or two on a sod farm. A steep angle, on the other hand, ma y last t wo sea- sons on golf course fairway turf and only half a season on a sod farm. N ...

  • Locke RS-5100 - page 25

    To achieve a 5 degree angle on the bedknife, rotate the bracket to the 5 degree reference mark. Figure 3- 28, arrow C. Refer to Figure 3-29 and 3-30: The front face should be ground at an angl e which insures the first contact with grass blades is made b y the cutting edge. 5 0 0 10 1 0 5 0 0 C Grinding A ngle Adjustment Figure 3-30 23 ...

  • Locke RS-5100 - page 26

    SECTION 4—MAINTENA NCE & LUBRI CA TION Clean-Up 1. After use, wash the unit with its own water supply which should have an anti-rust additive. T he res- ervoir holds approximatel y three gallons of clear water and recommended amounts of anti-rust ad- ditive. 2. Keep the wheel head carriage assembly clean. Figure 4-1 Refer to Figure 4-2 and 4- ...

  • Locke RS-5100 - page 27

    3. Clean the water reservoir and screens after a p- proximately 60 to 70 units of work. To remove the water reservoir: A. Disconnect the power supply. B. Remove the rear cover from the machine. C. Pull the drain hose out of the lid. D. Slide the tank out. Servicing the Stones EXTREME CARE MUST BE TAKEN TO AVOID CRACKING THE STONE. A CHIPPED OR BRO- ...

  • Locke RS-5100 - page 28

    SECTION 5—TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Electric motors won’t start Master button “ o ff” position T wist master button clockwise. It should “pop up” Spin motor won’t start Safety sw itch on hood not Close canopy engaged Pump runs but doesn’t W ater level low Add water pump water Valve off Open valve Suction screen ...

  • Locke RS-5100 - page 29

    Frequently Asked Questions SAFETY SHIELDS ARE INSTALLED FOR YOUR PROTECTION. 1. Why does the sharpener ha ve safety shields? Grinding stones frequently chip or even shatter, inju ring the oper ator of an unshielded sha r pen er. Also, in spin grinding, an unshiel ded rotating reel presents a co nsiderable hazar d to loose clothing, fingers, ha nds ...

  • Locke RS-5100 - page 30

    SAFETY DECALS To promote safe operation, Locke Turf supplies safety decals on all prod ucts manufactured. Because damage can occur to safety decals either through shipment, use or recondit ioning, Locke Turf will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Locke Turf dealer for mor ...

  • Locke RS-5100 - page 31

    T ORQUE SPECIFICA TIONS Proper torque for American fastene rs used on Locke Turf equipment. Recommended Torque in Foot Pound s (Newton Meters). * WRENCH SIZE (mm) “A” BOLT DIA. (mm) “B” AST M 4.6 AST M 8.8 AS TM 9.8 AST M 10.9 8 5 1.8 (2.4) 5.1 (6.9) 6.5 (8.8) 10 6 3 (4) 8.7 (12) 11.1 (15) 13 8 7.3 (10) 21.1 (29) 27 (37) 16 10 14.5 (20) 42 ...

  • Locke RS-5100 - page 32

    Locke T urf 307 Highway 52E Opp, Al abama 36467 (334) 493-1300 ...

Produzent Locke Kategorie Kitchen Utensil

Dokumente, die wir vom Produzenten des Geräts Locke RS-5100 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Locke
- Bedienungsanleitungen RS-5100
- Produktkarten Locke
- Informationsbroschüren
- oder Energieetiketten Locke RS-5100
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Locke RS-5100.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Locke RS-5100, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Locke RS-5100. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Locke RS-5100 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Locke RS-5100, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Locke RS-5100 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Locke RS-5100 verständlich ist.

Eine gänzliche Bedienungsanleitung von Locke sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Locke RS-5100 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Locke RS-5100 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Locke RS-5100, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Locke RS-5100 - die uns die ersten Schritte während der Nutzung von Locke RS-5100 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Locke RS-5100 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Locke RS-5100 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Locke RS-5100?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Locke RS-5100 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Locke RS-5100 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)