Bedienungsanleitung Cub Cadet 190-002

28 Seiten 3.84 mb
Download

Zur Seite of 28

Summary
  • Cub Cadet 190-002 - page 1

    IMPO RT AN T : Read saf ety rules a nd instructions ca refully bef o re operat ing equ ipment. CUB CADET CORP . P .O . BO X 368023 CLEVELAND , OHIO 44136-9722 Model 190 -002 30” Hy drau lic Tiller Attachment REQ UIRED FO R USE: W eight Kit Brac ket (190- 307-100) Suitcase W eights (3 Req’ d) (190 -390-1 00) PRINTED IN U .S.A. Oper ator’ s Man ...

  • Cub Cadet 190-002 - page 2

    2 TABLE OF CONTENTS Cont ent Pag e Important Safe O peratio n Practi ces .... ............. ............. ................... ............. ..... 3 Slope G auge ...... ............. ................... ............. ................... ............. ............. ..... 6 To the Owner ..... ............. ............. ................... ........... ...

  • Cub Cadet 190-002 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES W ARNING: This symb ol points out impo r tant saf ety instr uct ions whic h, if not followed, could endang er the pers onal safety and/or prop er ty of yourself and other s. Read and f ol low all instr uctions in this manual be f ore attempting to operate this ma chine. F ailure to comply wit h these ...

  • Cub Cadet 190-002 - page 4

    4 parking brake, turn engine off and remove key before dismounting. • Disengage the PTO, stop the engi ne and wait until the tiller comes to a complete stop before making any repairs, adjustments, or removing any rocks or debris. • Use extra caution when loading or unloading the machine into a trailer or truck. A tractor w ith a till er attachm ...

  • Cub Cadet 190-002 - page 5

    5 • Never remove gas cap or add fuel while the engine is hot or running. Allow engi ne to cool at least two minutes before refueling. • Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion. • Replace gasoline cap and tighten s ecurely. • If gasoline is spill ed, wipe it ...

  • Cub Cadet 190-002 - page 6

    6 SECTION 2: SLOPE GAUG E ...

  • Cub Cadet 190-002 - page 7

    7 SECTION 3: TO THE OWNER Model 190- 002-100 , 30-inch hydr aulic ti ller attac hment is de signed for use on Seri es 2000 Lawn Tr actors with 23 ” rear tires only. It w ill NOT fit no r operate pro perly or sa fely on AN Y other trac tor. Using this tille r attachm ent requir es the use of we ight kit brac ket 1 90-307- 100 and suit case we ight ...

  • Cub Cadet 190-002 - page 8

    8 To co nnect the hyd raulic hoses to t he hydr aulic pump assembl y: • Loca te both male hy draulic fittin gs on the hydr aulic pump. Notic e that the fit tings are not the s ame diameter . Figure 2 • Thread t he end of the sm all diam eter h ose onto the male end of the hy drauli c pump by han d, making sure to not c ross threa d the connec t ...

  • Cub Cadet 190-002 - page 9

    9 SECTION 6: PREPARING THE TRACTOR NOTE: References to LE FT and RIG HT indic ate the lef t and right sides of the tractor and ti ller attac hment when facing forw ard in the op erator’s po sition. NOTE: If the tr actor is equipped with a mower deck, remove i t now. Refer to the tractor’s operator’s manual for inst ructio n on rem oving th e ...

  • Cub Cadet 190-002 - page 10

    10 IMPORT ANT : I f working on or with the batter y for any reason, disconn ect the NEG A TIVE ( Black) wire fro m it ’ s ter minal fir st, f o llowed b y the POSITIVE (Red) wire. When reat taching the batter y c ables, alw ays connec t the POSITIV E (Red) wi re to the posi tive (+) batter y ter minal fir st, f o llowed b y th e NEGA TIV E (Black ...

  • Cub Cadet 190-002 - page 11

    11 • To mark the hole to ens ure proper centerin g of the new h ole to be dr illed, place the po inted end o f a cente r punch on the cross ha irs of new hol e position . Using a h ammer, s trike th e end of th e cente r punch to cr eate a perm anent mark in the metal fram e and carefu lly remo ve the tem plate. • Using a 7/1 6 ” drill bit, s ...

  • Cub Cadet 190-002 - page 12

    12 SECTION 7: MOUNTING THE TILLER Installing the Attachment Hitch The attac hment hitc h, which ha s the elec tric li ft cylind er attached to i t, attaches to the re ar of the tractor ’ s fr ame over the hitc h plate. Ther e is a short cl evis pin and cotter pi n mounted to the lo wer porti on of the attachmen t hitch during shippi ng, rem ove t ...

  • Cub Cadet 190-002 - page 13

    13 Attaching the Hydraulic Pump Assembly To m ount t he hydr auli c pump assem bly to t he tr actor , make certai n that it is pla ced unde r the center of the tractor ’ s fr ame, rest ing on th e ground, wi th the hydr aulic hos es att ached. Conne ct the hydrau lic pu mp asse mbly as foll ows: • The rea r of the hydraul ic pum p assembl y has ...

  • Cub Cadet 190-002 - page 14

    14 SECTION 8: KNOW THE TILLER Fig ure 14 Lift Switch The lif t switch is loca ted on t he right side of the stee ring wheel on the das h panel and i s used to raise and lower the till er atta chment and al so t o dete rmine t he de pth at which the tin es dig into the gr ound. Se e Figure 15. Fig ure 15 Push ing forwa rd, or up, on the swi tch will ...

  • Cub Cadet 190-002 - page 15

    15 R is the rev erse tillin g posit ion. The tin e direct ion lev er is push ed towar d the bac k of the m achin e, or aw ay from the o perator to start the t ines in the rever se direc tion. Tines spinni ng in a rev erse direction are used for breaking gr ound or til ling hard soi l. IMPORT ANT : Turn the tr actor ’ s PTO into the off position b ...

  • Cub Cadet 190-002 - page 16

    16 Engaging the Tiller NOTE: Refe r to th e trac tor ’ s operator ’ s m anual for informat ion co ncernin g starti ng and stop ping the tractor, and location an d proper usag e of its co ntrols. Before eng aging the til ler, comp lete the foll owing steps : • Start the tractor ’ s engi ne and make certain it is at operatin g temperatu re (t ...

  • Cub Cadet 190-002 - page 17

    17 For shall ow tilling, drop the rol ler to its lo west posit ion by putting th e locking rod into the hi ghest hole of the adjustme nt bar. For dee per tilling, c ontinu e to raise the roller by us ing lo wer holes in the adjustm ent bar . The lowest h ole ( highest settin g) is us ed for t ranspor ting the tiller. Using the Rear Tine Shield The ...

  • Cub Cadet 190-002 - page 18

    18 If the obje ct does not di slodge us ing this method and the tines co ntinue to not spin: • Shut off the P TO immed iately, s hift the tine directi on lev er to neutra l (N), raise t he ti ller to its highest po sitio n, and turn the trac tor engin e off. • Lift the rolle r to its h ighest position to cr eate eas ier access to the tines. Rai ...

  • Cub Cadet 190-002 - page 19

    19 Wit h the new fil ter i n place , remo ve all t ools us ed to change the fi lter from the tiller : • Start the tiller in mo tion for abo ut one minute in order to circ ulate the oil through the new filter . • Turn off the tiller and the tr actor, lower the tille r until the top fla t portion of the tiller is lev el with the ground, an d chec ...

  • Cub Cadet 190-002 - page 20

    20 Replace on ly one tine at a ti me. This will help to insu re the cor rect pos itioning of the tines a s they are m ounted on the tine ass embly. When installi ng the new tine, be certain that the lon ger shoul der bolt is in the inner hole toward the c enter of the tin e assembly. Re align the bolts and washe rs as show n in Figure 21 and retigh ...

  • Cub Cadet 190-002 - page 21

    21 SECTION 11: STORAGE NOTE: Before removing t he tiller a ttachm ent for storage , perform all lubr icatio n maint enance as outlined in th e Mainte nance sectio n. Removing the T iller NOTE: When r emovin g the t iller a ttachment, becau se the tiller is awkward, i t is recom mended that the tille r be removed in a place that will not requ ire it ...

  • Cub Cadet 190-002 - page 22

    22 Fig ure 25 • Holding the hitch latche s up will allow the tractor, with the attac hment hi tch sti ll moun ted, to be pushed away from the tiller with the slee ve hitch mounted to it. O nly push the tractor away a few inch es. • The hy drauli c pump asse mbly is st ill lyin g on the ground wit h the hose s attached. Careful ly push the tract ...

  • Cub Cadet 190-002 - page 23

    23 SECTION 13: TEMPLATES Dash P anel T emplate Instru ctions: 1. Carefully cut the temp late a long the dotted lines only . 2. T ape the template into position on the dash pan el. 3. Continue following instruction given on page 9, Installing the Lift Switch. ...

  • Cub Cadet 190-002 - page 24

    24 ...

  • Cub Cadet 190-002 - page 25

    25 Rear Frame T emplate Existing Hole Instruction s: 1. Carefully cut the template along the dotted lines only . 2. Continue following instruction given on page 10, Attachment Hitch Mounting Bolts. ...

  • Cub Cadet 190-002 - page 26

    ...

  • Cub Cadet 190-002 - page 27

    ...

  • Cub Cadet 190-002 - page 28

    MANUF A C TURER ’ S LIMITED W ARRANTY FOR: TWO-YEAR RESIDENTIAL ONE-YEAR COMMERCIAL Prope r maintenan ce of your Cub Cadet equi pment is the own er ’ s r espons ibility . Follow the ins tructi ons in your operator ’ s manual for cor rect lub ricants and mai ntenan ce sch edule. Yo ur Cub C adet de aler c arries a comple te line of qual ity lu ...

Produzent Cub Cadet Kategorie Tiller

Dokumente, die wir vom Produzenten des Geräts Cub Cadet 190-002 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cub Cadet
- Bedienungsanleitungen 190-002
- Produktkarten Cub Cadet
- Informationsbroschüren
- oder Energieetiketten Cub Cadet 190-002
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cub Cadet 190-002.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cub Cadet 190-002, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cub Cadet 190-002. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cub Cadet 190-002 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cub Cadet 190-002, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cub Cadet 190-002 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cub Cadet 190-002 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cub Cadet sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cub Cadet 190-002 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cub Cadet 190-002 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cub Cadet 190-002, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cub Cadet 190-002 - die uns die ersten Schritte während der Nutzung von Cub Cadet 190-002 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cub Cadet 190-002 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cub Cadet 190-002 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cub Cadet 190-002?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cub Cadet 190-002 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cub Cadet 190-002 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)