Deutsch dropdown-ico

Bedienungsanleitung Troy-Bilt 42031

32 Seiten 0.62 mb
Download

Zur Seite of 32

Summary
  • Troy-Bilt 42031 - page 1

    Models 42010 - 8 HP , 24" Auger 42030 - 8 HP , 24" Auger 42012 - 10 HP , 26" Auger 42031 - 10 HP , 26" Auger Owner/Operator Manual Snowthrower • Safety • Assembly • Controls • Operation • Maintenance ® GARDEN WAY INCORPORATED ...

  • Troy-Bilt 42031 - page 2

    2 Dear Owner: Thank you for purchasing this product. The unit was carefully designed and manufactured to provide excellent performance if properly operated and maintained. Read this manual. This is a safety , operation and general maintenance manual which does not attempt to cover major repairs. This manual is considered a permanent part of the uni ...

  • Troy-Bilt 42031 - page 3

    3 T able of Contents SECTION 1: SAFETY ..................................................................... 4 Safety Decals ............................................................................................................ 7 SECTION 2: ASSEMBLY ................................................................. 8 Inspect Unit/Tools Require ...

  • Troy-Bilt 42031 - page 4

    T raining 1. Read this owner/operator manual and the separate engine owner manual carefully before operating the unit. Be completely familiar with the controls and the proper use of the unit. A replacement manual is available by contacting the factory. 2. Never allow children or untrained adults to use the unit. 3. Keep the area of operation clear ...

  • Troy-Bilt 42031 - page 5

    5 Section 1 : Safety 3. Before starting the engine, check the tightness of all screws, nuts, bolts, and other fasteners. Replace or clean any damaged or unreadable safety and operating labels. 4. Wear adequate winter outer garments when operating the unit. Wear footwear that will improve footing on slippery surfaces. Exercise caution to avoid slipp ...

  • Troy-Bilt 42031 - page 6

    6 11. Before inspecting the unit or making any adjustments, or if the unit jams or becomes clogged, shut the engine off immediately and allow all moving parts to come to a stop. Disconnect the spark plug wire from the spark plug and secure the wire away from the spark plug. Use only a wooden stick (at least 3 feet long) to clear away any blockage. ...

  • Troy-Bilt 42031 - page 7

    7 Section 1 : Safety 5. Allow the engine to cool before storing in any enclosure. 6. Store gasoline in a cool, well- ventilated area, safely away from any spark- or flame-producing equipment. 7. Store gasoline only in an approved gasoline storage container, safely out of the reach of children. 8. Use only original equipment replacement parts. Parts ...

  • Troy-Bilt 42031 - page 8

    Assembly 8 Section 2 IMPORTANT: Follow the assembly steps carefully. Contact the factory or your local authorized dealer if you have any questions or problems. A. Inspect Unit Inspect the unit and shipping crate for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and ...

  • Troy-Bilt 42031 - page 9

    9 Section 2: Assembly A J B C E F D G H I IMPORTANT: Left and right sides of the unit are determined from the operator position, facing the direction of forward travel. E. Install Handlebars 1. Cut the plastic cable ties securing the handlebar ends to the chassis and remove the handlebars. Remove the protective wrapping on the handlebars. 2. Attach ...

  • Troy-Bilt 42031 - page 10

    10 Section 2: Assembly F . Install Discharge Chute 1. Remove the cardboard packing shield from the discharge chute mount opening. 2. Loosen (do not remove) the left and right side sets of plastic shims (G, Fig. 2-4, inset A) and plastic hold-down clips (H, Fig. 2-4, inset A) on the toothed flange (J) of the discharge chute assembly. Remove and save ...

  • Troy-Bilt 42031 - page 11

    11 Section 2: Assembly Fig. 2-7 Y Fig. 2-8 AH AC AD AB AA AT AS AG R AF AE 5. Rotate the chute control crank (Z, Fig. 2-6). The deflector chute should turn freely. Adjust the worm gear assembly bracket (L, Fig. 2-4) as necessary to prevent binding. H. Attach Auger Drive Control Rod 1. Remove the plastic cable tie that secures the auger drive contro ...

  • Troy-Bilt 42031 - page 12

    12 Section 2: Assembly Fig. 2-9 AF AB Yellow Yellow & Red Wires AL AO AN AM AK Black Black Blue Red Fig. 2-10 I. Attach Wheel Drive Control Rod 1. Remove the plastic cable tie that secures the wheel drive control rod (AE, Fig. 2-8) and the gear shift control rod (AF) to the left handlebar. 2. Hook the spring (AG, Fig. 2-8) at the lower end of t ...

  • Troy-Bilt 42031 - page 13

    13 Section 2: Assembly K. Wiring Harness Installation 1. Remove the plastic cable tie that secures the wiring harness to the right handlebar. 2. Route the wiring harness to the inside of the right handlebar and over to the right side of the engine. 3. Attach the ring terminal (AK, Fig. 2-10) on the two black wires to the screw on the engine shroud ...

  • Troy-Bilt 42031 - page 14

    14 Controls This section defines the various controls on the unit. Refer to the following section, “Operation,” for an explanation of the proper use of these controls. A, Fig. 3-1—Wheel drive control lever Controls the engagement of the wheel drive. When this lever is down against the handlebar and the engine is running, the wheels will rotat ...

  • Troy-Bilt 42031 - page 15

    15 Section 3: Controls H, Fig. 3-4—Throttle Located on back left corner of the engine, the throttle controls the speed of the engine. For proper operation information, refer to the following section, “Operation.” NOTE: The engine lubrication and cooling systems operate best at full throttle. Operating the engine at less than full throttle for ...

  • Troy-Bilt 42031 - page 16

    Operation 16 Pre-operation checklist 1. Review Section 1, “Safety” and Section 3, “Controls” in this manual. 2. Check the unit for any loose or missing hardware. Tighten or replace as needed. 3. Check inside the auger housing and the discharge chute and remove any debris. 4. Check the engine oil level: a. Move the unit onto a level surface. ...

  • Troy-Bilt 42031 - page 17

    17 Section 4: Operation Fill the fuel tank with fresh, clean unleaded gasoline with a minimum octane rating of 87. Leave 1/2" of space for fuel expansion. DO NOT MIX OIL WITH GASOLINE! Tighten the gasoline fill cap securely. Refer to the engine owner manual for additional gasoline information. DO NOT MIX OIL WITH GASOLINE! 6. The unit should b ...

  • Troy-Bilt 42031 - page 18

    18 Starting the engine 1. Review the “Pre-operation checklist” earlier in this section. Move the unit outside to a well-ventilated, level area. 2. Move the gearshift lever (B, Fig. 4-4) into the desired gear position. 3. Turn the ignition key (C, Fig. 4-4) to the RUN “ ” position. 4. Turn choke knob “ ” (D, Fig. 4-5) clockwise to FULL C ...

  • Troy-Bilt 42031 - page 19

    19 Auger drive engagement 1. Remove any debris from inside the auger housing. 2. Adjust the discharge chute deflector cap (RR, Fig. 4-6) angle with adjustment lever (SS, Fig. 4-6). The discharge chute deflector cap should usually be adjusted to a low angle, so it is not pointing at any persons, animals, buildings or vehicle, especially in windy con ...

  • Troy-Bilt 42031 - page 20

    20 Section 4: Operation T ransporting the unit Release the auger drive control lever to disengage the auger drive whenever the unit is being transported to the work site. The unit is extremely heavy. Have at least one other person help you when loading or unloading the unit into a truck or trailer. Use ramps when loading or unloading the unit onto ...

  • Troy-Bilt 42031 - page 21

    Maintenance 21 Engine oil Check the engine oil level each time before starting the unit and after each 5 hours of operation. To check the engine oil level: 1. Move the unit onto a level surface. 2. Remove the oil dipstick (A, Fig. 5-1). 3. Wipe the oil from the dipstick with a clean cloth. 4. Screw the dipstick back into the engine. 5. Remove the o ...

  • Troy-Bilt 42031 - page 22

    22 Section 5: Maintenance Lubrication At the beginning and end of each season or after every 25 hours of operation, lubricate the unit as recommended below: 1. Lightly oil both the deflector chute cap pivot points (D, Fig. 5-3). 2. Lightly oil the discharge chute control rod pivot points where the control rod enters the control panel bearing (E, Fi ...

  • Troy-Bilt 42031 - page 23

    length of spring (W, Fig. 5-6) again. The spring length should now measure 5/8" – 3/4" (15–19mm) longer than the measurement taken in step 2. If it does not, loosen jam nut (Y, Fig. 5-6) and turn adjuster (Z, Fig. 5-6) to increase or decrease the spring length. (1-1/4 turns of the adjuster equals 1/16" [1.5mm] of spring extension ...

  • Troy-Bilt 42031 - page 24

    24 Auger Drive Belt Adjustment Due to wear, the auger drive belt may begin to slip when the auger drive lever is engaged. To adjust the auger drive belt: 1. Perform the brake arm adjustment as described later in this section. 2. If assembling a new unit, raise the wheel drive control lever (AP, Fig. 5-9) and the auger drive control lever (AL). 3. P ...

  • Troy-Bilt 42031 - page 25

    25 Section 5: Maintenance 5. Remove the auger drive belt from the lower drive pulley (AO). 6. Remove the belt from unit. To install the auger drive belt: 1. Position the auger drive belt (AD) down through gap. Position the belt into the lower drive pulley (AO). 2. Position the auger drive belt (AD) into pulley (AE). Reinstall the belt guide (AC) an ...

  • Troy-Bilt 42031 - page 26

    26 Section 5: Maintenance Brake Arm Adjustment The brake arm adjustment is set at the factory to 1/16 - 1/8” for proper belt/brake clearance. Due to wear this may need adjustment. To perform this adjustment: 1. Remove the bolts, flat washer, lock washer and belt cover (AB, Fig. 5-9). 2. Squeeze the auger drive control lever (AL, Fig. 5-9) against ...

  • Troy-Bilt 42031 - page 27

    27 Section 5: Maintenance POSSIBLE PROBLEM Ignition key in STOP position Choke knob in incorrect position Engine throttle lever in incorrect starting position Engine not primed enough (when cold) Engine primed too much (when cold) Spark plug wire disconnected Fouled or faulty spark plug Gasoline tank empty Fuel shutoff valve is closed Carb / fuel l ...

  • Troy-Bilt 42031 - page 28

    28 Section 5: Maintenance TROUBLE Auger drive control lever does not engage auger drive Auger spins with drive lever disengaged Wheel drive control lever does not turn wheels Wheels turn with wheel drive control lever disengaged Snowthrower does not throw snow well Snowthrower does not clear snow Snowthrower makes sloping cut in snow Electric start ...

  • Troy-Bilt 42031 - page 29

    29 Section 5: Maintenance Interval Before each use After each use Every 25 hours of operation or annually Every 50 hours of operation or annually Annually Item Engine oil All fasteners Auger drive lever Wheel drive lever Handlebar control levers and linkages Snowthrower Engine oil Tires Auger gear box Belts Cooling air screen Spark plug Drive chain ...

  • Troy-Bilt 42031 - page 30

    30 Specifications Snowthrower Models 42010, 42012, 42030, & 42031 Snowthrower Height ......................To top of handlebar levers: 41.5" (105.3 cm) ...........w/o handlebars, deflector cap down: 33" (83.75 cm) Length........................................With handlebars: 70" (177.6 cm) ....................................Wit ...

  • Troy-Bilt 42031 - page 31

    31 Specifications Wiring Diagram DIODE/RECTIFIER ENGINE CONNECTOR RED BLUE IGNITION SWITCH HANDLEBAR HEATER HANDLEBAR HEATER GROUND TO HANDLEBAR BLACK To Light (optional) BLACK RED RED YELLOW RED YELLOW ENGINE SHROUD GROUND SCREW ENGINE CONNECTOR RED GREEN OFF ON TO MAGNETO TO ENGINE STATOR ...

  • Troy-Bilt 42031 - page 32

    For customer assistance, contact your nearest authorized dealer or: GARDEN WAY INCORPORATED • 1 Garden Way • Troy, New York U.S.A. 12180 Customer Service: 1-800-437-8686 • Technical Service: 1-800-520-5520 • Parts Service: 1-800-648-6776 • FAX: (518) 391-7332 Outside the U.S.A. and Canada: Customer Service: (518) 391-7007 • For Technica ...

Produzent Troy-Bilt Kategorie Snow Blower

Dokumente, die wir vom Produzenten des Geräts Troy-Bilt 42031 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Troy-Bilt
- Bedienungsanleitungen 42031
- Produktkarten Troy-Bilt
- Informationsbroschüren
- oder Energieetiketten Troy-Bilt 42031
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Troy-Bilt 42031.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Troy-Bilt 42031, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Troy-Bilt 42031. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Troy-Bilt 42031 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Troy-Bilt 42031, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Troy-Bilt 42031 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Troy-Bilt 42031 verständlich ist.

Eine gänzliche Bedienungsanleitung von Troy-Bilt sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Troy-Bilt 42031 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Troy-Bilt 42031 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Troy-Bilt 42031, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Troy-Bilt 42031 - die uns die ersten Schritte während der Nutzung von Troy-Bilt 42031 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Troy-Bilt 42031 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Troy-Bilt 42031 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Troy-Bilt 42031?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Troy-Bilt 42031 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Troy-Bilt 42031 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)