Deutsch dropdown-ico

Bedienungsanleitung Makita LF1000

30 Seiten 2.49 mb
Download

Zur Seite of 30

Summary
  • Makita LF1000 - page 1

    Model No. Description NEW T OOL C ONCEPT AND MAIN APPLICA TIONS S pecif ication P 1 / 30 Flip Over Sa w 260mm (10-1/4") Model LF1000 is the first flip o ver saw from Makita. Miter saw and T able saw are combined for great versatility . Its main adv antages are; W eighs only 32kg (70lbs) for easy transport to job sites. Quick miter saw/table sa ...

  • Makita LF1000 - page 2

    P 2 / 30 S tandard equipment Assorted TCT sa w blades Note: The standard equipment for the tool sho wn abov e may differ by country . TCT saw blade ......... 1 pc V ise ass'y ................. 1 pc Dust bag ass'y .......... 1 pc Ruler ass'y ................ 1 pc Box wrench 13-3 ...... 1 pc Push stick ................. 1 pc Fix plate ...

  • Makita LF1000 - page 3

    P 3 / 30 R epair [1] NECESSAR Y REP AIRING T OOLS CA UTION: Remove the saw blade fr om the machine for safety bef ore r epair/ maintenance ! Code No. 1R003 Retaining ring S Pliers ST -2N Removing Retaining ring from Safety co ver 1R207 45 degree Set square Setting the miter/be vel angle of saw blade to 45 de grees 1R208 90 degree Set square Setting ...

  • Makita LF1000 - page 4

    P 4 / 30 R epair [2] LUBRICA TION (cont.) Apply Makita grease N. No.1 to the follo wing portions designated with the black triangle to protect parts and product from unusual abrasion. See Fig.2 . Slide plate L T able complete T urn table Slide plate R 153 153 Guide fence 228 Sleev e 8 260 The both ends which contact Frame set. The surface that cont ...

  • Makita LF1000 - page 5

    P 5 / 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -1. Handle Section Fig. 4 Fig. 3 Fig. 5 DISASSEMBLING The Handle section can be disassembled without separating Motor housing from Blade case. T ake the following steps: 1) Set the machine in the mode of miter saw . And lock the saw head unit at the lo west position by pushing Knob 20 as illustrated i ...

  • Makita LF1000 - page 6

    P 6 / 30 R epair [3] DISASSEMBL Y/ASSEMBL Y DISASSEMBLING ASSEMBLING [3] -2. Switch Box (On/Off Switch Section) Do the re verse of the disassembling steps. Fig. 10 Fig. 9 1) First, disconnect the right hinge of Switch cov er from Switch box using slotted screwdri ver . ( Fig. 9 ) 2) Then, while lifting up the right hinge, pull of f the left hinge f ...

  • Makita LF1000 - page 7

    P 7 / 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -3. Motor Housing Fig. 12 Fig. 13 DISASSEMBLING Fig. 11 Motor housing 1) Remov e Brush holder caps and Carbon brushes from Motor housing. 2) Remov e four M6x60 Pan head scre ws using No.3 Phillips screwdri ver . ( Fig. 11 ) Note: Motor housing can not be separated from Blade case in this step because ...

  • Makita LF1000 - page 8

    P 8 / 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -4. Gear Section Fig. 17 Fig. 15 Fig. 18 DISASSEMBLING Fig. 14 1) Disconnect T ension spring 4 from Blade case. By removing Retaining ring S-42 with Retaining pliers ST -2N (No.1R003), Safety cov er can be separated from Blade case. ( Fig. 14 ) 2) By unscre wing four M5x16 Countersunk head screws, the ...

  • Makita LF1000 - page 9

    P 9 / 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -5. Blade Case Section Fig. 21 Fig. 22 DISASSEMBLING Fig. 19 Fig. 20 1) Remov e Safety cover as illustrated in Fig . 14 . 2) Remov e Dust nozzle. Then remov e Hex socket head bolt M6x30 and Flat w asher 6 for disconnecting the cutting depth adjusting mechanism and Connecting rod. ( Fig. 19 ) 3) Loosen ...

  • Makita LF1000 - page 10

    P 10/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y Fig. 23 Fig. 24 Fig. 25 ASSEMBLING [3] -5. Blade Case Section (cont.) Slide Slee ve 13 as far as possible to ward Steel ball 6. At this time, the distance between Sleeve 13 and the neck of Knob 40 will be about 7mm. While keeping the distance, secure Connecting rod to Sleev e 13 with Hex socket head bolt ...

  • Makita LF1000 - page 11

    P 11/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -6. Riving Knife Fig. 27 Fig. 26 DISASSEMBLING 1) Loosen W ing nut M8. 1) First, fix ri ving knife as illustrated in Fig. 26 . 2) Remov e Stop ring E-4, then loosen W ing bolt M8. Now Ri ving knife can be removed. ( Fig . 27 ) 2) Pull Ri ving knife a little in the direction of arro w . 3) T urn Riving ...

  • Makita LF1000 - page 12

    P 12/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -7. T able Section Fig. 29 Fig. 30 Fig. 28 DISASSEMBLING Pan head scre w M4x10 Pan head scre w M4x10 Thrust needle gauge 1022 Lev er 100 Hex nut M10-17 Spacer Arm complete When disassembling the T able section, Arm complete has to be separated from Sub arm. Ho wev er , it is not necessary to separate ...

  • Makita LF1000 - page 13

    P 13/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y DISASSEMBLING [3] -7. T able Section (cont.) Fig. 33 Fig. 34 6) Now the T able section can be removed from Guide fence by unscre wing nine M6x20 Hex socket head bolts from the back side of T able complete. ( Fig. 32 ) 7) Remov e Hex socket head bolt M8x50 and Flat washer 8 from each end of Guide fence. ( ...

  • Makita LF1000 - page 14

    P 14/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y DISASSEMBLING [3] -7. T able Section (cont.) Fig. 35 9) Lev er (Lock lev er) is fastened to Frame with each two pieces of Hex socket b utton head bolt M6 and Flat washer 7. When removing Le ver , follow the instruction described in Fig . 35 . Hex socket button head bolt M6 Lev er Flat washer 7 T orsion sp ...

  • Makita LF1000 - page 15

    P 15/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Frame Section Fig. 37 Fig. 39 Fig. 38 Fig. 40 DISASSEMBLING 1) After removing Switch box, place the Frame section as illustrated in Fig. 37 , and remov e four Square pipes by unscrewing eight M8x20 He x socket head bolts. 2) Place the Frame section as illustrated in Fig. 38 . Then, by removing fou ...

  • Makita LF1000 - page 16

    P 16/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Frame Section (cont.) ASSEMBLING Fig. 41 Fig. 42 Fig. 43 1) Fasten Scre w M10 to left Frame/ right Frame so that Pipe 32 complete/ Pipe 32 cov ers 2 pitches of the thread portion on the opposite side of the scre w when the pipe is set in place over the scre w . ( Fig. 41 ) 2) T ighten Frames with ...

  • Makita LF1000 - page 17

    Hex bolt M6x45 Flat washer 6 P 17/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -9. Assembling Feet Section Fig. 44 Fig. 45 1) For smooth folding action of the Feet section, follo w the steps described below to assemble Support brack et to Square pipes precisely at an angle of 90 degrees: i) Put Support bracket on Square pipe 32-510, while keeping abo ...

  • Makita LF1000 - page 18

    P 18/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -9. Assembling Feet Section (cont.) Fig. 48 4) T o Square pipe 32-510, assemble Hook and Foot. And to Square pipe 32-475, assemble Stopper hook and Foot nut. ( Fig. 48 ) LEFT FEET SECTION Stopper hook Hook Square pipe 32-510 Hex nut M6 Foot Foot Foot bolt Compression spring 13 Foot nut Foot nut Square ...

  • Makita LF1000 - page 19

    P 19/ 30 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -10. Assembling Feet Section to Frame Section Fig. 50 Fig. 51 W ith eight M8x20 Hex socket bolts, f asten the left Feet section to Frame, left; and the right Feet section to Frame, right. Important: a) Before assembling, be sure that the follo wing parts are in the correct position as illustrated in F ...

  • Makita LF1000 - page 20

    P 20/ 30 R epair [4] ADJUSTMENT [4] -1. Adjusting Bevel Angle Fig. 52 Fig. 53 Fig. 54 Fig. 55 1) Lock the saw head unit in the full do wn position, and loosen Lev er 100. Then rotate the 90 de gree adjusting screw two or three turns counterclockwise using He x wrench 3, and tilt the blade to the right. ( Fig. 52 ) 2) Put 90 degree set square (No.1R ...

  • Makita LF1000 - page 21

    P 21/ 30 R epair [4] ADJUSTMENT [4] -2. Adjusting Miter Angle Fig. 56 Fig. 57 1) Lock the saw head unit in the full do wn position. 2) Slightly loosen four M6x20 hex sock et head bolts that fasten the Arm section to T urn table. ( Fig. 56 ) 3) Lightly tighten one of the four bolts. Then, applying 90 de gree set square (No.1R208) to the side of saw ...

  • Makita LF1000 - page 22

    C ircuit diagram P 22/ 30 All European Countries Except UK-110V Color index of lead wires' sheath Black White Red Orange Blue Brown Purple Y ellow A1 3 1 31 41 A2 4 2 32 42 Motor Housing Switch Box Handle A B A B Cord from Switch box Handle Noise suppressor T erminal block Strain relief Strain relief Noise suppressor Band Line filter Choke coi ...

  • Makita LF1000 - page 23

    C ircuit diagram P 23/ 30 UK-110V Color index of lead wires' sheath Black White Red Orange Blue Brown Purple Y ellow *Pick up coil is factory-assembled to Controller . When Connecting Wires to Relay; Attach Receptacle slee ve (indicated by in the diagram) to the Receptacle on the wires to connect with the follo wing terminals: No.5, No.42, No. ...

  • Makita LF1000 - page 24

    P 24/ 30 W iring diagram Lead wire holder D Motor housing Motor housing Choke coil, connected with Controller Choke coil Controller Controller Opening B Opening A Field lead wire (orange) Field lead wire (black) Field lead wire (yello w) Field lead wire (white) Field lead wire (purple) Lead wires of Pick up coil Fix two wires of Pick up coil with t ...

  • Makita LF1000 - page 25

    P 25/ 30 W iring diagram [2] Wiring in Handle All European Countries Except UK-110V Switch Line filter Strain relief 10 - 20mm 10 - 20mm Connecting cord from Switch box L-shaped rib Inside wall A Lead wires from Controller and Field Bottom of Handle Handle cov er side Brake switch Bottom of Handle Handle cov er side Connect lead wires to Brake swit ...

  • Makita LF1000 - page 26

    P 26/ 30 W iring diagram [3] Wiring in Switch Box All European Countries Except UK-110V Switch box Grommet Connecting cord from Handle Power supply cord Relay When mounting Grommet to Switch box, be sure to place; *the big end outside of Switch box *the small end inside of Switch box. Small end of Grommet Big end of Grommet Strain relief Strain rel ...

  • Makita LF1000 - page 27

    P 27/ 30 W iring diagram [4] Wiring at Connecting Rod All Countries [5] Wiring Under T able Switch box Grommet Strain relief Pan head scre w M4x10 Frame complete Connecting cord from Switch box to Handle Connecting cord Pan head scre w M4x10 Connecting rod Strain relief Handle Connecting cord (from Switch box) Cord guard Blade case Be sure that Con ...

  • Makita LF1000 - page 28

    P 28/ 30 W iring diagram Lead wire holder D Motor housing Motor housing Choke coil, connected with Controller Choke coil Controller Controller Opening B Opening A Field lead wire (orange) Field lead wire (black) Field lead wire (yello w) Field lead wire (white) Field lead wire (white) Lead wires of Pick up coil Fix two wires of Pick up coil with th ...

  • Makita LF1000 - page 29

    P 29/ 30 W iring diagram [2] Wiring in Handle UK-110V Switch Line filter Strain relief 10 - 20mm 10 - 20mm Connecting cord from Switch box L-shaped rib Inside wall A Lead wires from Controller and Field Band Noise suppressor Be careful not to route lead wires ov er Strain relief. Put Line filter between Strain relief and Band. Install Connecting co ...

  • Makita LF1000 - page 30

    P 30/ 30 W iring diagram [3] Wiring in Switch Box UK-110V Switch box Grommet Connecting cord from Handle Power supply cord Relay When mounting Grommet to Switch box, be sure to place; *the big end outside of Switch box *the small end inside of Switch box. Small end of Grommet Big end of Grommet Strain relief Strain relief T erminal block Noise supp ...

Produzent Makita Kategorie Router

Dokumente, die wir vom Produzenten des Geräts Makita LF1000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Makita
- Bedienungsanleitungen LF1000
- Produktkarten Makita
- Informationsbroschüren
- oder Energieetiketten Makita LF1000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Makita LF1000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Makita LF1000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Makita LF1000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Makita LF1000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Makita LF1000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Makita LF1000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Makita LF1000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Makita sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Makita LF1000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Makita LF1000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Makita LF1000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Makita LF1000 - die uns die ersten Schritte während der Nutzung von Makita LF1000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Makita LF1000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Makita LF1000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Makita LF1000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Makita LF1000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Makita LF1000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)