-
Ultra Start 26XX Series - page 1
Co v er s All 25xx and 26xx Series R emote Star ter/ Alar ms -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle. - CARBON MONOXIDE ...
-
Ultra Start 26XX Series - page 2
T able of Contents INST ALLATION MANUAL REMOTE V EHICLE S T ARTER/ALARM Page 2 Pre-Inst allation Page 3 Components Feature List Pre-Installation Inst allation Procedures Page 4 Wiring Diagrams Page 5-7 Wire Description Page 8-9 6 Pin Connector 14 Pin Connector Auxiliary Outputs Optional Connectors Jumper Positions Quick S t art Inst allation Page 1 ...
-
Ultra Start 26XX Series - page 3
R ecommended Pre-Installation Procedures F eature List - Control module - 2 4 button transmitters* - Antenna with built in - 6 pin main harness with dual - Program Button and LED’s 30 amp power inputs. - Multi-tone Siren - 3 pin auxiliary output harness - 14 pin harness - 4 pin Auxiliary sensor harness - 4 pin keyless entry harness - 2 pin T empe ...
-
Ultra Start 26XX Series - page 4
R ecommended Installa tion Procedures Under Hood Connections - Route the hood pin and tach wire through the firewall into the engine compartment. If possible route the wires through a factory rubber grommet. If drilling a hole through the firewall, BE CAREFUL . Always check for obstructions on both sides of the firewall. After drilling, use a snap ...
-
Ultra Start 26XX Series - page 5
REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL Page 5 Wiri ng Diagra m 1 3 5 2 4 6 2 1 4 3 6 5 7 8 10 10 10 9 12 12 11 11 14 13 13 4P I N BLUE 30 AMP ST ARTER DISABLE RELA Y - NORMALL Y CONNECTED Blue Green Red Red Y ellow White /Green White /Blue Red St a r t e r Heater Main Power Ignition 1 Selectable Main Power F ACTOR Y RE-ARM STA RTER DI ...
-
Ultra Start 26XX Series - page 6
Page 6 INST ALLATION MANUAL REMOTE V EHICLE S T ARTER/ALARM Side View PI N 4 RE D P N 4I WE HI T 4 P IN W HITE P N 3 I W HIT E Note-250ma outputs are low current and are designed to activate relays Green Pink Blue Programmable * AUX #1 (Hold 1&3) * / (-) HORN OUTPUT* AUXILIARY OUTPUT #2 (Hold 2&3) Programmable (+) Input (+)DISCONNECT/ (+) S ...
-
Ultra Start 26XX Series - page 7
Page 7 REMOTE V EHICLE ST ARTER/ALARM INST ALLATION MANUAL 6-pin Description T est For Wire 1-Y ellow 30amp S tarter Output This wire will test 0volts in of f, accessory and in the ignition position.12volts during st art only . 2-Green 30amp Heat/Acc Output This wire will test 0volts in the of f position 12- 14volts in the accessory and run positio ...
-
Ultra Start 26XX Series - page 8
Page 8 INST ALLATION MANUAL REMOTE V EHICLE ST ARTER/ALARM 14 Pin Connector Continued F r om Pre vious Page 1-Green Door Lock Door Lock Output - Programmable Menu 1 2-Red 12vlt Output Output For Door Lock Module Only! 3-Blue Door Unlock Door Unlock Output - Programmable Menu 1 4-Pink 2nd Unlock Output when button #2 is pressed twice. * The centre p ...
-
Ultra Start 26XX Series - page 9
Page 9 REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL 6 Pin P o w er Connector S t e p1-C onnect All Of the F ollo wing W ir es Y ellow 30amp S tarter Output 12volt s during start position only . Green 30amp Heater Output 12volts in the accessory position off during start and 12volt s during run. Red 30amp Power Input Constant 12volt power at ...
-
Ultra Start 26XX Series - page 10
Step 1 - Connect All Of the F ollo wing W ir es 6 Pin P o w er Connector Y ellow 30amp St arter Output 12volts during st art position only . Green 30amp Heater Output 12volts in the accessory position off during st art and 12volt s during the run position. Red 30amp Power Input Constant 12volt power at ignition harness or battery . Red 30amp Power ...
-
Ultra Start 26XX Series - page 11
Manual T ra nsmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation. Park Brake Input- This w ...
-
Ultra Start 26XX Series - page 12
Auto T ach Learn 1) T urn the ignition key to the “ON” position. (The park lights will turn on*). 2) S tart the vehicle with the key , The LEDs on the antenna will turn on if a proper t ach signal is detected**, then after 30-35 seconds the p ark lights will flash and the siren will chirp twice to confirm T ach Learn. * If the park lights do no ...
-
Ultra Start 26XX Series - page 13
Impor tant T ac h Notes T ach Learning the remote st arter is one of the most import ant steps in the inst allation process. Do not tach learn vehicle while the engine is in high idle. T o ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM. V ehicles such as T oyot a and Honda may idle much higher wh ...
-
Ultra Start 26XX Series - page 14
Entering Pr ogr am Mode 1) With the ignition in the OFF position, turn the ignition key from “Of f” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park light s will flash and the siren will chirp to confirm entering program mode. ...
-
Ultra Start 26XX Series - page 15
Quic k Vie w Progr amming * See the following p ages for more det ailed programming instructions. Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp T ype 1 T ype 2 All Chirps 3 Lock&Unlock Options Double Unlock 3 second .75 second 4 Unlock/Disarm 125ms 750ms 5. Passive Locks Enable Disable ...
-
Ultra Start 26XX Series - page 16
Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Lock Button Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Chirp Doors Lock/Unlock with Ignition key . 2) Ignition Lock Only 2 Flashes/Chirps Doors Lock when ignition is turned ON only . *3) Ignition Auto Lock Disable 3 Flashes/Chirp ...
-
Ultra Start 26XX Series - page 17
Menu 1- User Settings .. . continued from pr e vious page Setting 5 Active/Passive Locks 1) No Auto-Lock with Passive Arm 1 Flash/Chirp No auto-lock with passive arming *2) Doors Auto-Lock with Passive Arm 2 Flashes/Chirp s Doors Lock when p assive arming Press & Release the Program Button 5 T imes (Setting 5) Confirmed with 5 LED flashes. Pres ...
-
Ultra Start 26XX Series - page 18
*(Default Settings) Menu 2 - Additional Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Unlock Button Setting 1 Secure V alet Mode - Length of time required to set the system into Service Mode 1) Secure V alet 1 Flash/chirp Hold the Program Button for 15 seconds *2) Normal V alet 2 Flashes/chirp s Hold the Program Button ...
-
Ultra Start 26XX Series - page 19
Page 19 Menu 3- Star ter Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #3 Setting 1 S pecial Door Lock/Unlock Operations (Factory Alarm Rearm) . 1) T ype 1 1 Flash/chirp Unlock before st art. Lock pulse after st art and on shut down. 2) T ype 2 2 Flashes/chirps Lock pulse ONL Y af ter remote start shut down. *3) ...
-
Ultra Start 26XX Series - page 20
Menu 4- T ac h Settings Setting 1 Auto T ach Learn. 1) Perform a System Reset. See p age 15. 2) T urn the ignition key on. (Park lights will turn on). 3) S tart the vehicle, the LEDs on the antenna will come on when a proper t ach signal is detected*. 4) After approximately 30-35 seconds the p ark light s will go out then will flash twice and the s ...
-
Ultra Start 26XX Series - page 21
Page 21 REMOTE V EHICLE S T ARTER/ALARM INST ALLATION MANUAL Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Button - Th e park Lights will turn ON and the siren will chirp once. If the park lights do not come on at this point, turn the ignition key off f or 5 seconds, then repeat st ...
-
Ultra Start 26XX Series - page 22
87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Ve h i c l e Lock/Unlock Switch T o Control Relay or Actuator Green Fused +12V Blue Ground Ne ga tiv e Type Door Loc ks 250ma Ne ga tiv e Door Loc ks (More T han 250ma) P ositiv e T ype Door Locks Note: When installing relays always use a fused power source. Blue Green Lock Un lock V ehicle Lock/Unlock S ...
-
Ultra Start 26XX Series - page 23
87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock V ehicle Lock/Unlock Switch To Actuator Fused +12V x x Cut Cut 87 86 85 87a 30 Ground DIA GNOSTICS 13 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock T o V acuum Pump Fused +12V x Cut Ground Page 23 REMOTE V EHICLE ST ARTER/ALARM INST ALLATION MANUAL 5 W ir e / R e v er se P olarity Ty ...
-
Ultra Start 26XX Series - page 24
DIA GNOSTICS If the remote starter does not activate when the st art button is pressed the p ark lights will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the p ark lights flash 3 times slowly . Looking at the chart below this would indicate that the system is in Service Mode, si ...
Haben Sie eine Frage bezüglich Ultra Start 26XX Series?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ultra Start 26XX Series nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ultra Start 26XX Series hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.