Bedienungsanleitung Swisher ZT2560

16 Seiten 0.76 mb
Download

Zur Seite of 16

Summary
  • Swisher ZT2560 - page 1

    REPAIR MANUAL ZT2560 Swisher Mower Co Warrensburg, MO ...

  • Swisher ZT2560 - page 2

    TABLE OF CONTENTS 1. If engine won’t crank 2. If engine won’t crank – continued 3. If engine cranks but won’t start If engine stalls when PTO is engaged 4. If PTO clutch will not engage Hour meter not operating 5. Wire identification at switches 6. Wire identification at switches – continued 7. Drive control adjustment 8. Drive control ad ...

  • Swisher ZT2560 - page 3

    IF ENGINE WON’T CRANK ALWAYS CHECK FUSE FIRST TEST #1 Using a remote starter switch or suitable device, make a connection between the large ter minals on the solenoid. If engine does not crank!!! • Battery may be weak or dead • Starter may be bad • Battery cables may have bad connections • Do not go to Test #2 until this test gives result ...

  • Swisher ZT2560 - page 4

    A neutral switch is located on the lower end of bot h drive control handles and is activated when the handles are outward in the neutral position. Check that the plunger buttons on both switches are depressed at least 3/8”. Meter should go to zero when checking continuity across switch terminals with plungers depressed. With PTO switch in the off ...

  • Swisher ZT2560 - page 5

    ENGINE CRANKS BUT WON’T START Checks for electrical problems • While turning ignition switch to its first position, listen for the fuel solenoid on the carburetor to click. It must click to supply fuel to the carburetor. • Try a new spark plug. • Check for spark at plug when it is re moved and the threaded end is grounded. • Unplug the si ...

  • Swisher ZT2560 - page 6

    IF PTO CLUTCH WILL NOT ENGAGE HOUR METER NOT OPERATING Hour meter has a positive and a negative post. Gray wire should go on the positive. Power is supplied from the ignition switch. Green wire from hour meter is grounded by the oil pressure switch, therefore only has a ground when the engine is running. Apply a negative ground to this terminal App ...

  • Swisher ZT2560 - page 7

    WIRE IDENTIFICATION AT SWITCHES 3623 IGNITION SWITCH STARTER SOLENOID Heavy red cable goes to the starter. Red wire goes to ignition switch. Green wire goes to neutral switches and on to the ignition switch. Green wire with orange stripe goes to the ground. Red wire goes to engine plug. Heavy red cable goes to the positive post of the battery. PTO ...

  • Swisher ZT2560 - page 8

    WIRING HARNESS TO EN GINE PLUG CONNECTION Gray wire goes to carburetor fuel solenoid Green wire goes to oil pressure switch Black wire goes to engine ignition module Red wire goes to engine charging system Green wire goes to hour meter Red wire goes to terminal on solenoid with the positive battery cable. Black wire goes to the ignition switch. Gra ...

  • Swisher ZT2560 - page 9

    BATTERY CHARGING SYSTEM To test alternator before it goes to the regulator, unplug the yellow connector and measure the AC voltage across the the two gray wires inside this connector.There should be at least 20 volts AC. CARBURETOR FUEL SOLENOID Red wire goes to the engine plug and then on to the positive terminal of the solenoid to keep the batter ...

  • Swisher ZT2560 - page 10

    DRIVE CONTROL ADJUSTMENTS LEFT SIDE SHOWN Control plate shown in neutral position Hydro linkage Start your adjustments by putting the drive control arms in the neutral position. Remove the linkage from the control plate at the Eaton hydro by removing the cotter pin and washer on the under side. By moving the control plate forward and backwards by h ...

  • Swisher ZT2560 - page 11

    OVERVIEW OF DRIVE CONTROL LINKAGE RIGHT SIDE SHOWN Right side control handle Pivot point for control handle moveme nt Pivot point Adjustment threads on control rod Forward and reverse control on hydrostat DRIVE CONTROL ADJUS TMENTS (CONTINUED) LEFT SIDE SHOWN Once both hydro units are pulling equally, make your fina l control handle adjustment with ...

  • Swisher ZT2560 - page 12

    PARKING BRAKE AND NEUT RAL SWITCH OPERATION Parking brake cable atta ches here. Right side is shown. Control panel has been removed for better view. Right side drive control handle. Safety switch rocker arm pivots on a bolt at this point. Parking brake is activated by this bolt as the drive control handle is swung outward in the neutral position. T ...

  • Swisher ZT2560 - page 13

    DECK LIFTING SYSTEM Three rocker arms are activated by the deck lift handle. This is the right side control. Note the routing of the cabl e. It drops straight below to the deck. This center rocker arm lifts the front center of the deck. It also drops through the lower frame but is directed by two pulleys under the mower frame to the front of the de ...

  • Swisher ZT2560 - page 14

    DECK BELT REPLACEMENT ENGINE TO DECK BELT •Lower the deck to lowest setting •Loosen tension on tension idler •Remove worn or damaged belt •Using part# 10263 belt, route it around the engine pulley as shown in the diagram. •Retighten the tensi on idler and check the operation DECK CROSS BELT •Remove the belt covers •Remove the engine t ...

  • Swisher ZT2560 - page 15

    REPAIRING OR REPLACING BLADE DRIVER Torque top nut to 90 ft/lbs Replacing this nut each time is recommended. Pulley does not have a hub. When removing, just lift it off like a washer, no puller is needed. Machine washers are used to keep the pulley from contacting the outer ra ce of the bearing. When applying torque to the top nut the pressure is t ...

  • Swisher ZT2560 - page 16

    For additional assistance on service Contact Swisher Mower Co., Inc. Phone 1-800-222-8183 Fax 1-660-747-3160 E-mail cust.serv@swisherinc.com 14 ...

Produzent Swisher Kategorie Lawn Mower

Dokumente, die wir vom Produzenten des Geräts Swisher ZT2560 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Swisher
- Bedienungsanleitungen ZT2560
- Produktkarten Swisher
- Informationsbroschüren
- oder Energieetiketten Swisher ZT2560
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Swisher ZT2560.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Swisher ZT2560, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Swisher ZT2560. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Swisher ZT2560 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Swisher ZT2560, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Swisher ZT2560 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Swisher ZT2560 verständlich ist.

Eine gänzliche Bedienungsanleitung von Swisher sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Swisher ZT2560 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Swisher ZT2560 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Swisher ZT2560, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Swisher ZT2560 - die uns die ersten Schritte während der Nutzung von Swisher ZT2560 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Swisher ZT2560 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Swisher ZT2560 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Swisher ZT2560?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Swisher ZT2560 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Swisher ZT2560 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)