Bedienungsanleitung CrimeStopper RS-840

12 Seiten 0.57 mb
Download

Zur Seite of 12

Summary
  • CrimeStopper RS-840 - page 1

    RS-840 Model REMOTE ENGINE STARTING SYSTEM OPERATING INSTRUCTIONS INTRODUCTION Congratulations on your choice of a Crimestopper CoolSt art remote engine starter! This installation Handbook covers the RS-840 Model Remote Start & Keyless Entry System. *IMPORTANT INFORMATION: Primary and Optional Features -PRIMARY: These are features that must be ...

  • CrimeStopper RS-840 - page 2

    TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Remote Control Diagrams………...……………………………………………………………………………...…….3 Remote Engine Control…………….…..………………? ...

  • CrimeStopper RS-840 - page 3

    REMOTE CONTROL DIAGRAM #3 #1 #2 #4 LOCK T RUNK ENGINE UNLO CK VEHICLE #2 FLA SHL IGHT (A UX.) ST A RT /ST OP RS-840 SYSTEM The transmitter supplied with the RS-840 system has a tota l of 6 buttons. The button configuration of the RS-840 is Factory-set and unchangeable. See Page 11 for additional information on how to use your remote to operate a se ...

  • CrimeStopper RS-840 - page 4

    REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1 second. 2) Parking lights flash once; return solid, and the Ignition/Accessory circuits turn on. 3) After a few seconds the Starter Motor engages, Parki ng lights and Accessory circuits will turn off while cranking. 4) Engine Starts and ...

  • CrimeStopper RS-840 - page 5

    REMOTE ENGINE CONTROL ENTERING YOUR REMOTE STARTED VEHICLE: 1) With engine running, Remote Unlock system or open door with key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset) 3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park. 4) Remote starter will reset ...

  • CrimeStopper RS-840 - page 6

    REMOTE ENGINE CONTROL INFINITY RUN MODE This mode can only be activated when "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses . This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the ...

  • CrimeStopper RS-840 - page 7

    TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the CoolStart syst em to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors rem otely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of ...

  • CrimeStopper RS-840 - page 8

    CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as y ...

  • CrimeStopper RS-840 - page 9

    CONVENIENCE AND SAFETY FEATURES HOOD OPEN SAFETY (Requires grounding hood pin installation) This feature prevents the engine from being remote started when hood is open. Helps eliminates risk of injury to someone working under the hood of the vehicle with a properly working hood pin installed. If Remote Start button is pressed with the hood open, t ...

  • CrimeStopper RS-840 - page 10

    TRANSMITTER PROGRAMMING TRANSMITTER PROGRAM DIAGRAM: IGN OFF WAIT F O R 4 FLA SHES PRESS 4 X's FLA SH 2, 3, or 4 X's (GRA Y WIRE GR OUNDED) IGN OFF PRESS LOCK BUTTON COMPLETE 10 ...

  • CrimeStopper RS-840 - page 11

    2-VEHICLE OPERATION The RS-840 system can be used for 2 vehicle operation. A single remote can control a second vehicle with an RS-840 or other CoolStart system installed. There are some exceptions. See “Multi-Vehicle Notes” section below. VEHICLE #2 Press low er s ide button first, then you hav e 3 seconds to control v ehicle #2. Pressing the ...

  • CrimeStopper RS-840 - page 12

    TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit senses a fault at the Brake (Purple wire is active) or the Hood is OPEN (Gray wire grounded). This is a safety feature of the unit. Check installation for faults and make sure hood is closed and latched and brake wire is not active. UNIT C ...

Produzent CrimeStopper Kategorie Remote Starter

Dokumente, die wir vom Produzenten des Geräts CrimeStopper RS-840 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen CrimeStopper
- Bedienungsanleitungen RS-840
- Produktkarten CrimeStopper
- Informationsbroschüren
- oder Energieetiketten CrimeStopper RS-840
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung CrimeStopper RS-840.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen CrimeStopper RS-840, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen CrimeStopper RS-840. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts CrimeStopper RS-840 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts CrimeStopper RS-840, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von CrimeStopper RS-840 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von CrimeStopper RS-840 verständlich ist.

Eine gänzliche Bedienungsanleitung von CrimeStopper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von CrimeStopper RS-840 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von CrimeStopper RS-840 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich CrimeStopper RS-840, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts CrimeStopper RS-840 - die uns die ersten Schritte während der Nutzung von CrimeStopper RS-840 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit CrimeStopper RS-840 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von CrimeStopper RS-840 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich CrimeStopper RS-840?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit CrimeStopper RS-840 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit CrimeStopper RS-840 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)