Bedienungsanleitung Snapper EMRP216518B

28 Seiten 1.04 mb
Download

Zur Seite of 28

Summary
  • Snapper EMRP216518B - page 1

    Safety Instructions & Operator’s Manual for EUROPEAN 21” STEEL DECK WALK MOWERS (TYPE ‘M’) SERIES 18 PROPELLED MODELS EMRP216518B MODEL NUMBER EXPLANATION E M R P 21 65 18 B EUROPEAN MODEL ENGINE DESIGNATION MODEL DESIGNATION SERIES DESIGNATION RECYCLING MODEL ENGINE HORSE POWER * SELF-PROPELLED CUTTING WIDTH E – European Model P – ...

  • Snapper EMRP216518B - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This po w e rful cutting machine is capable of amputa ting hands and feet and can throw objec ts that can cause injury and damage! Failure to comply with the foll owing SAFETY instructions could result in s erious injury or death to the operator or other persons. The owner of the ma chine must understand the ...

  • Snapper EMRP216518B - page 3

    3 IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. DO NOT refuel the machine indoors. 5. DO NOT store the machine or fuel container inside where there is an open flame, spark or pilot light such as on a ...

  • Snapper EMRP216518B - page 4

    4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 11. Have machine serviced by an authorized SNAPPER dealer at least once a year and ha ve the dealer install any new sa fet y devices. 12. Use only genuine SNAPPER replacement parts to assure that original standards are maintained. ...

  • Snapper EMRP216518B - page 5

    5 TABLE OF CONTENTS IMPORTANT SAFETY IN STRUCTIONS .............................................. 2 - 4 TABLE OF CO NTENTS ............................................................................. 5 SECTION 1 - FAMI LIARIZAT ION .............................................................. 6 SECTION 2 - OPERATIN G INSTRUCTION S ............... ...

  • Snapper EMRP216518B - page 6

    6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has bee n prepared for the operators of the SNAPPER WALK BEHIND MOWE RS. Its purpose, aside from re commending operating and routine service requirem ents, is to promote safety through the use of a ccepted operating practices. Read, Understand and Follow the “IMPORTANT SAFETY I ...

  • Snapper EMRP216518B - page 7

    7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required be fore each start-up. 2.1.1. Check guards, deflectors , grass bag, adapte r and covers to make sure all are in p lace and securely tightened. 2.1.2. Check blade control and wheel drive control to insure they work freely. See Fig ...

  • Snapper EMRP216518B - page 8

    8 Section 2 - OPERATING INSTRUCTIONS 2.2.2. PROPELLI NG MOWE R 1. Start engine. Refer to Section “Starting & Operation”. 2. Move ground speed control to the desire d speed position. See Figure 2.5. 3. Move wheel drive control against handle to engage wheel drive and propel m ower forward. Forward speed can be ad justed while the mower is mo ...

  • Snapper EMRP216518B - page 9

    9 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.6 RECYCLING OPERATION (Optional ...

  • Snapper EMRP216518B - page 10

    10 Section 2 - OPERATING INSTRUCTIONS 2.8 INSTALLATION, COLLECTOR GRAS S BAG (Optional accessory on some models) STEP 1: Install the gras s bag adapter and secure to the side and top of the deck with the two nuts provided on the machine. Slot in front edge o f adapter m ust be under nut located on top of deck. See Figure 2.9. STEP 2: Install grass ...

  • Snapper EMRP216518B - page 11

    11 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.8 INSTALLATION of DISCHARGE DE ...

  • Snapper EMRP216518B - page 12

    12 Section 3 – MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and seri al number. 3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL ...

  • Snapper EMRP216518B - page 13

    13 Section 3 – MAINTENANCE 3.2.2. CHECK GREASE LEVEL IN TRANSMISSION (Continued from previous page ) NOTE: Do not spill grease or oil on surface of drive disc. See Figure 3.3. 3. Reinstall transmission plug. 4. Check grease level after each 25 hours of operation. FIGURE 3.3 WARNING DO NOT attempt any maintenance, adjustments or service w ith engi ...

  • Snapper EMRP216518B - page 14

    14 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade runnin g. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. E ngine and components are HOT. Avoid serious burns; allo w sufficien t time for all components to cool. Wear he avy leather gloves ...

  • Snapper EMRP216518B - page 15

    15 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade runnin g. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. E ngine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.1.2. BLADE SHARPENING 4. S ...

  • Snapper EMRP216518B - page 16

    16 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade runnin g. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. E ngine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3 DRIVEN AND DRIVE DISC SE ...

  • Snapper EMRP216518B - page 17

    17 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.3. DRIVEN DISC ADJUSTMENT ...

  • Snapper EMRP216518B - page 18

    18 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.4. Replacing Rubber Driven ...

  • Snapper EMRP216518B - page 19

    19 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3.6. Replacement Of Bearing ...

  • Snapper EMRP216518B - page 20

    20 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service w ith engine and blade runnin g. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. E ngine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.4.1. Engine Drive Belt Rep ...

  • Snapper EMRP216518B - page 21

    19 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRE CTIVE ACTION Engine Will Not Sta rt 1. Fuel tank empty. 1. F ill fuel tank with fresh fuel. Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. Engine Stalls or Stops A ...

  • Snapper EMRP216518B - page 22

    20 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Clea n Sponge Element Engine Manual & Page 13. X** Air Cleaner Clean or Replace Engine Manual. X** Spark Plug Replace Engine Manual. X En ...

  • Snapper EMRP216518B - page 23

    21 DECAL IDENTIFICATION (1) WARNING INSTRUCTIONS. (2) WARNING: Do Not operate w i thout entire Grass Catcher or Guard in place. (3) PRIME (on engine): Use for initial engine starting. Read and follow engine operating and maintena nce instructions. Push bulb to prime engine. (4) SPARK PLUG: Warns of potential electrical shock from spark plug while e ...

  • Snapper EMRP216518B - page 24

    22 DECAL IDENTIFICATION (6) OPERATOR PRESENCE CONTROL (OPC): Arrow points to the OPC bail. When bail is rotated rearward, the engine may be started and will run as indicated by the engine with rotating arro w . With the engine running, the blade is rotating as indicated by the cut grass sy mbol. When the bail is released and rotates for w ard, the ...

  • Snapper EMRP216518B - page 25

    23 2 YEAR LIMITED WARRANTY For two (2) years from purchase date fo r the orig inal purchaser's residential, non-comme rcial use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for ta xes where applicab le), any part o r parts found upon examination by the factory at McDo nough, Georgia, to be d efective in ...

  • Snapper EMRP216518B - page 26

    24 NOTES 26 ...

  • Snapper EMRP216518B - page 27

    25 NOTES 27 ...

  • Snapper EMRP216518B - page 28

    26 Safety Instructions & Operator’s Manual for EUROPEAN 21” STEEL DECK WALK BEHIND MOWERS (TYPE ‘M’) SERIES 18 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emiss ions requirements on the date manufactured. The labe ls on those engines contain very important emissions information and critica l saf ...

Produzent Snapper Kategorie Security Camera

Dokumente, die wir vom Produzenten des Geräts Snapper EMRP216518B erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Snapper
- Bedienungsanleitungen EMRP216518B
- Produktkarten Snapper
- Informationsbroschüren
- oder Energieetiketten Snapper EMRP216518B
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Snapper EMRP216518B.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Snapper EMRP216518B, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Snapper EMRP216518B. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Snapper EMRP216518B ansehen.

Die komplette Bedienungsanleitung des Geräts Snapper EMRP216518B, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Snapper EMRP216518B hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Snapper EMRP216518B verständlich ist.

Eine gänzliche Bedienungsanleitung von Snapper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Snapper EMRP216518B bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Snapper EMRP216518B befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Snapper EMRP216518B, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Snapper EMRP216518B - die uns die ersten Schritte während der Nutzung von Snapper EMRP216518B erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Snapper EMRP216518B hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Snapper EMRP216518B im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Snapper EMRP216518B?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Snapper EMRP216518B nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Snapper EMRP216518B hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)