Bedienungsanleitung Dell W04C

59 Seiten 7.33 mb
Download

Zur Seite of 59

Summary
  • Dell W04C - page 1

    Dell OptiPlex 9020 AIO Owner's Manual Regulatory Model: W04C Regulatory Type: W04C002 ...

  • Dell W04C - page 2

    Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 201 ...

  • Dell W04C - page 3

    Contents 1 Working on Your Computer....................................................................................................... 5 Before Working Inside Your Computer ..................................................................................................................... 5 Recommended Tools ................................... ...

  • Dell W04C - page 4

    Installing the Power-Supply Fan ............................................................................................................................. 24 Removing the I/O Board Shield ............................................................................................................................... 25 Installing the I/O Board Shi ...

  • Dell W04C - page 5

    1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that ...

  • Dell W04C - page 6

    CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Recommended Tools The procedures in this document may requ ...

  • Dell W04C - page 7

    After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. 1. Replace the cover. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 2. Connect any telephone or network c ...

  • Dell W04C - page 8

    2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. System Overview Figure 1. Inside View 1. power supply unit (PSU) 2. camera 3. hard drive 4. processor fan 5. coin-cell battery 6. heat sink assembly 7. heat sink 8. memory module 8 ...

  • Dell W04C - page 9

    9. WLAN card 10. speakers 11. input/output (I/O) board shield 12. power-supply fan 13. power-supply fan bracket 14. intrusion switch 15. converter board 16. power-button and on-screen display (OSD) buttons board 17. optical drive Removing the VESA Stand 1. Follow the procedures in Before Working Inside Your Computer . 2. Place the computer on a fla ...

  • Dell W04C - page 10

    5. Remove the screws that secure the VESA stand to the computer and lift the VESA stand away from the computer. Installing the VESA Stand 1. Align and place the VESA stand on the back of the computer. 2. Tighten the screws that secure the VESA stand to the computer. 3. Place and press the VESA cover on the computer, until it clicks into place. 4. F ...

  • Dell W04C - page 11

    4. Lift the cover and remove it from the computer using the notches near the input/output (I/O) panel. Installing the Back Cover 1. Align the back cover to its original position on the computer and press until it clicks in place. 2. Tighten the screws to secure the back cover to the computer. 3. Install the VESA stand. 4. Follow the procedures in A ...

  • Dell W04C - page 12

    3. Lift the memory shield outwards. 4. Pry the retention clips away from the memory module until it pops-up. Lift and remove the memory module from its connector. Installing the Memory 1. Align the notch on the memory-card with the tab in the system-board connector. 2. Press down on the memory module until the release tabs spring back to secure the ...

  • Dell W04C - page 13

    Installing the VESA Mount Bracket 1. Align and place the bracket on the back of the computer. 2. Tighten the screws that secure the VESA mount bracket to the computer. 3. Install the: a. back cover b. VESA stand 4. Follow the procedures in After Working Inside Your Computer . Removing the Power and On-Screen Display (OSD) Buttons Board 1. Follow th ...

  • Dell W04C - page 14

    Installing the Power and OSD Buttons Board 1. Align and place the power and OSD buttons board on the computer. 2. Connect the cable to the power and OSD buttons board. 3. Install: a. back cover b. VESA stand 4. Follow the procedures in After Working Inside Your Computer . Removing the System-Board Shield 1. Follow the procedures in Before Working I ...

  • Dell W04C - page 15

    Installing the System-Board Shield 1. Align and place the system-board shield on the back of the computer. 2. Tighten the screws that secure the system-board shield to the computer. 3. Install the: a. VESA mount bracket b. back cover c. VESA stand 4. Follow the procedures in After Working Inside Your Computer . Removing the Converter Board 1. Follo ...

  • Dell W04C - page 16

    Installing the Converter Board 1. Place the convertor board into its place. 2. Tighten the screws to secure the converter board to the computer. 3. Connect the backlight and converter cables to the converter board. 4. Install the: a. back cover b. VESA stand 5. Follow the procedures in After Working Inside Your Computer . Removing the Coin-Cell Bat ...

  • Dell W04C - page 17

    4. Slide the optical drive outward and disconnect the optical-drive cable. 5. Slide and lift the optical drive from the computer. 6. Remove the screws that secure the optical-drive bracket to the optical drive. Remove the optical-drive bracket from the optical drive. 17 ...

  • Dell W04C - page 18

    Installing the Optical Drive 1. Place the optical-drive bracket on the optical drive. 2. Tighten the screws that secure the optical-drive bracket to the optical drive. 3. Align and slide the optical drive into its slot. 4. Connect the optical-drive cable. 5. Tighten the screws that secure the optical drive to the computer. 6. Install the: a. back c ...

  • Dell W04C - page 19

    5. For a 2.5–inch hard drive, remove the screws that secure the hard drive to the hard-drive bracket. Slide the hard drive from the hard-drive bracket. Remove the screws that secure the hard-drive case to the hard drive. 6. For a 3.5–inch hard drive, remove the screws that secure the hard drive to the hard-drive bracket. Slide the hard drive fr ...

  • Dell W04C - page 20

    c. VESA stand 7. Follow the procedures in After Working Inside Your Computer . Removing the Intrusion Switch 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. VESA stand b. back cover c. VESA mount bracket d. system-board shield 3. Disconnect the intrusion-switch cable from the connector on the system board. Unthre ...

  • Dell W04C - page 21

    Installing the Intrusion Switch 1. Place the intrusion switch on the computer and tighten the screw to secure it to the chassis. 2. Thread the cable along the notches on the chassis and connect the intrusion-switch cable to the connector on the system board. 3. Install: a. system-board shield b. VESA mount bracket c. back cover d. VESA stand 4. Fol ...

  • Dell W04C - page 22

    Installing the WLAN Card 1. Align and place the WLAN card on the WLAN adapter. Tighten the screws to secure the WLAN card to the WLAN adapter 2. Place the WLAN card along with the WLAN adapter on its connector and tighten the screws to secure the WLAN card to the system board. 3. Connect the WLAN cables. 4. Install: a. system-board shield b. VESA m ...

  • Dell W04C - page 23

    d. VESA stand 4. Follow the procedures in After Working Inside Your Computer . Removing the Processor Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. VESA stand b. back cover c. VESA mount bracket d. system-board shield 3. Disconnect the processor-fan cable from the connector on the system board. Remove the s ...

  • Dell W04C - page 24

    4. Remove the screws that secure the power-supply fan to the chassis and lift it away from the computer. Installing the Power-Supply Fan 1. Place the power-supply fan on the computer and tighten the screws to secure it to the chassis. 2. Align and place the fan duct from the computer. 3. Tighten the screw that secures the fan duct to the chassis. 4 ...

  • Dell W04C - page 25

    Removing the I/O Board Shield 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. VESA stand b. back cover c. VESA mount bracket d. power supply fan e. system-board shield 3. Lift the I/O panel away from the computer. 4. Remove the screws that secure the power connector to the I/O board shield. 5. Remove the screws t ...

  • Dell W04C - page 26

    6. Flip the input/output (I/O) board shield and remove it from the computer. 7. Disconnect the power-connector cable from the system board. 26 ...

  • Dell W04C - page 27

    Installing the I/O Board Shield 1. Connect the power-connector cable to the system board. 2. Place the I/O board shield on the computer. 3. Pass the power connector and fix it to the socket. Tighten the screws that secure the I/O board shield to the chassis. 4. Tighten the screws that secure the power connector to the I/O shield. 5. Place the I/O p ...

  • Dell W04C - page 28

    4. Remove the screws that secure the PSU to the chassis. Lift the PSU up and remove it from the computer. Installing the Power Supply Unit 1. Place the power supply unit on the computer. 2. Tighten the screws to secure the power supply unit to the chassis. 3. Thread the cable on the hooks in the computer. 4. Connect the power-supply cables to the c ...

  • Dell W04C - page 29

    6. Follow the procedures in After Working Inside Your Computer . Removing the Processor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. VESA stand b. back cover c. VESA mount bracket d. system-board shield e. heat-sink assembly 3. Press the release lever down and then move it outward to release it from the retent ...

  • Dell W04C - page 30

    4. Remove the screws that secure the speakers to the chassis. Lift the speakers from the computer. Installing the Speakers 1. Place and align the speakers on the chassis. Tighten the screws that secure the speaker to the chassis. 2. Thread the cables on the notches. Connect the speaker cables to the system board. 3. Install: a. system-board shield ...

  • Dell W04C - page 31

    Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. VESA stand b. back cover c. VESA mount bracket d. system-board shield e. memory f. optical drive g. hard drive h. heat-sink assembly i. power supply unit j. input/output (I/O) board shield k. converter board l. power-supply fan 3. Disconnec ...

  • Dell W04C - page 32

    1. SATA ODD power connector 2. SATA HDD connector 3. SATA HDD power connector 4. SATA ODD connector 5. graphic heat sink fan connector 6. intrusion switch connector 7. processor heat sink fan connector 8. camera connector 9. coin-cell battery connector 10. processor socket 11. memory connectors (SODIMM sockets) 12. speaker connector 13. mini-PCI Ex ...

  • Dell W04C - page 33

    Installing the System Board 1. Place the system board on the computer. 2. Connect all the cables to the system board. 3. Tighten the screws to secure the system board to the base panel. 4. Install: a. power-supply fan b. converter board c. input/output (I/O) board shield d. power supply unit e. heat-sink assembly f. hard drive g. optical drive h. m ...

  • Dell W04C - page 34

    4. Press and push down the screws that are connected to the system board. 5. Remove the heat sink from the system board. Installing the Heat Sink (Graphics Card) 1. Place the heat sink on the system board. 2. Press the screws to lock the heat sink to its position. 3. Connect the fan cable. 4. Install: a. system board b. power-supply fan c. converte ...

  • Dell W04C - page 35

    d. input/output (I/O) board shield e. power supply unit f. heat-sink assembly g. hard drive h. optical drive i. memory j. system-board shield k. VESA mount bracket l. back cover m. VESA stand 5. Follow the procedures in After Working Inside Your Computer . Removing the Antenna Module 1. Follow the procedures in Before Working Inside Your Computer . ...

  • Dell W04C - page 36

    Installing the Antenna Module 1. Place the antenna module on the chassis. 2. Thread the antenna cable around the edges of the computer. Tighten the screws to secure the antenna module to the chassis 3. Install: a. system board b. power-supply fan c. heat-sink assembly d. power supply unit e. processor fan f. converter board g. power and OSD buttons ...

  • Dell W04C - page 37

    NOTE: These instructions are valid only for non-touch computers. For touch computers, the display panel should be disassembled in a clean-room environment. 3. Disconnect the LVDS cable from the display panel. Remove any other cables or antennae around the edges of the base panel. 4. Remove the screws that secure the base panel to the chassis. Lift ...

  • Dell W04C - page 38

    6. Remove the screws that secure the display bracket to the display panel. Remove the display bracket from the display panel. Installing the Display Panel 1. Tighten the screws to secure the display bracket to the display panel. 2. Place the display panel on the chassis. 3. Place the base panel on the chassis. 4. Tighten the screws to secure the ba ...

  • Dell W04C - page 39

    f. power supply unit g. power-supply fan h. converter board i. power and OSD buttons board j. intrusion switch k. hard drive l. optical drive m. WLAN card n. input/output (I/O) board shield o. system-board shield p. VESA mount bracket q. back cover r. VESA stand 7. Follow the procedures in After Working Inside Your Computer . Removing the Camera 1. ...

  • Dell W04C - page 40

    Installing the Camera 1. Tighten the screws to secure the camera to the chassis. 2. Connect the camera cable and fix the latch. 3. Install: a. display panel b. system board c. power-supply fan d. heat-sink assembly e. power supply unit f. processor fan g. converter board h. power and OSD buttons board i. intrusion switch j. hard drive k. optical dr ...

  • Dell W04C - page 41

    3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardware • View the system hardware configuration • Enable or disable integrated devices • Set performance and power management thresholds • Manage ...

  • Dell W04C - page 42

    Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only. <Esc> Moves to the previous page till you view the main scr ...

  • Dell W04C - page 43

    Option Description • Apply - Enables you to apply the settings. • Exit - Exits and starts the computer. Advanced Boot Options The Enable Legacy Option ROMs option will allow the legacy option ROMs to load, when in UEFI boot mode. Without this option, only UEFI option ROMs will load. This option is required for Legacy boot mode. This Legacy boot ...

  • Dell W04C - page 44

    Option Description USB Configuration This field configures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any type of USB mass storage devices (HDD, memory key, floppy). If USB port is enabled, device attached to this port is enabled and available for operation system. If USB port is disabled, the operation ...

  • Dell W04C - page 45

    Option Description The drive does not have a password set by default. • Enter the old password • Enter the new password • Confirm the new password Internal HDD-4 Password Allows you to set, change, or delete the password on the computer's internal hard disk drive (HDD). Successful changes to this password take effect immediately. The dri ...

  • Dell W04C - page 46

    Option Description • Disable • Enable - This option is enabled by default • On-Silent CPU XD Support Allows you to enable or disable the execute disable mode of the processor. • Enable CPU XD Support - This option is enabled by default. OROM Keyboard Access Allows you to determine if you access the Option Read Only Memory (OROM) configurati ...

  • Dell W04C - page 47

    Option Description • Reset All Keys - Resets to default setting • Delete All Key s- Deletes all the keys NOTE: If you disable the Custom Mode, all the changes made will be erased and the keys will restore to default settings. Table 6. Performance Option Description Multi Core Support Specifies whether the process will have one or all cores enab ...

  • Dell W04C - page 48

    Option Description • Last Power State Auto On Time This option sets the time of the day when you would like the system to turn on automatically. Time is kept in standard 12-hour format (hour:minutes:seconds). The startup time can be changed by typing the values in the time and A.M./P.M. fields. • Disabled - The system will not automatically pow ...

  • Dell W04C - page 49

    Option Description POST Hotkeys Specifies whether the sign-on screen displays a message, that displays the keystroke sequence required to enter the BIOS Boot Option Menu. • Enable F12 Boot Option menu - This option is enabled by default. Fastboot Speeds up the boot process by bypassing some compatibility steps. The options are: • Minimal • Th ...

  • Dell W04C - page 50

    Option Description SERR Messages Controls the SERR message mechanism. This option is not set by default. Some graphics cards require that the SERR message mechanism be disabled. Table 12. Cloud Desktop Option Description Server Lookup Method This option specifies how the Cloud Desktop software will lookup the server address. The options are: • St ...

  • Dell W04C - page 51

    Option Description NOTE: This option is relevant only when the Integrated NIC control in the System Configuration group is set to Enable with Cloud Desktop. Table 13. System Logs Option Description BIOS events Displays the system event log and allows you to clear the log. • Clear Log Updating the BIOS It is recommended to update your BIOS (system ...

  • Dell W04C - page 52

    CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended. NOTE: Your computer is shipped with the system and setup password feature disabled. Assigning a System Password and Setup Password You can assign a new S ...

  • Dell W04C - page 53

    NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the System and/or Setup password, confirm the deletion when promoted. 5. Press <Esc> and a message prompts you to save the changes. 6. Press <Y> to save the changes and exit from the System Setup. The computer reboots. 53 ...

  • Dell W04C - page 54

    4 Technical Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer. Table 14. System Information Feature Specification Processor type • Intel Dual / Quad Core • Intel C ...

  • Dell W04C - page 55

    Table 17. Audio Feature Specification Controller Intel High Definition Audio with Waves MaxxVoice Pro Speaker single 8-ohms speakers in both the left and right speaker assembly (5 W average per channel) Internal speaker amplifier up to 15 W per channel Internal microphone support dual digital microphone Volume controls Volume up/down buttons (Windo ...

  • Dell W04C - page 56

    Table 22. Ports and Connectors Feature Specification Audio: • one line-out connector • one audio input/microphone port • one headphone port Network adapter one RJ45 connector USB 2.0 four USB 3.0 four Video 15-pin VGA connector HDMI one 19-pin output port Media card reader one 8-in-1 slot Table 23. Power Feature Specification 200 Watt PSU Fre ...

  • Dell W04C - page 57

    Feature Without Stand With Stand non-touch 70.50 mm (2.78 inches) 174.40 mm (6.87 inches) touch 72.80 mm (2.87 inches) 174.40 mm (6.87 inches) Weight: non-touch 8.10 kg to 8.76 kg (17.86 lb to 19.31 lb) 10.25 kg to 10.91 kg (22.60 lb to 24.05 lb) touch 9.19 kg to 9.84 kg (20.26 lb to 21.70 lb) 11.34 kg to 11.99 kg (25.00 lb to 26.43 lb) NOTE: The w ...

  • Dell W04C - page 58

    Feature Specification Relative humidity (maximum): Operating 10% to 90% (non-condensing) Storage 10% to 95% (non-condensing) Maximum vibration: Operating 0.66 GRMS Storage 1.30 GRMS Maximum shock: Operating 110 G Storage 160 G Altitude: Operating –15.2 m to 3048 m (–50 to 10,000 ft) Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborn ...

  • Dell W04C - page 59

    5 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your are ...

Produzent Dell Kategorie Personal Computer

Dokumente, die wir vom Produzenten des Geräts Dell W04C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Dell
- Bedienungsanleitungen W04C
- Produktkarten Dell
- Informationsbroschüren
- oder Energieetiketten Dell W04C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Dell W04C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Dell W04C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Dell W04C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Dell W04C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Dell W04C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Dell W04C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Dell W04C verständlich ist.

Eine gänzliche Bedienungsanleitung von Dell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Dell W04C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Dell W04C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Dell W04C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Dell W04C - die uns die ersten Schritte während der Nutzung von Dell W04C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Dell W04C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Dell W04C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Dell W04C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Dell W04C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Dell W04C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)