-
Ryobi 2075r - page 1
MODEL 2075r GAS TRIMMER OPERA TOR’S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA IMPORT ANT MANUAL DO NOT THROW AW A Y ...
-
Ryobi 2075r - page 2
INTRODUCTION 2 T ABLE OF CONTENTS THANK YOU Thank you for purchasing this quality pr oduct. This modern outdoor power tool is designed to provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to- understand operating instructions. Read the entire manual and follo ...
-
Ryobi 2075r - page 3
3 SP ARK ARRESTOR CALIFORNIA EMISSION REGULA TIONS SAFETY WARNINGS The engine of your lawn and garden car e product meets the 1995 to 1998 California emissions regulations. These units ar e identified by the label on the engine of your product. A typical identification label is shown. T o ensure that your unit continues to meet these regulations, r ...
-
Ryobi 2075r - page 4
WHILE OPERA TING • W ear safety glasses or goggles and ear/hearing protection at all times when operating this unit. Always wear a face or dust mask if the operation is dusty . • Dress pr operly . Do not operate this unit when barefoot or wearing open sandals. Always wear sturdy , rubber -soled footwear . The use of gloves and long pants are re ...
-
Ryobi 2075r - page 5
SAFETY WARNINGS 5 • Keep all bystanders, especially children and pets, at least 30 feet (9.1 m) away from the unit during operation. • Do not operate the engine faster than the speed necessary to cut, trim or edge. Do not run the engine at high speed when not cutting. • Always stop the engine when cutting is delayed or when walking from one c ...
-
Ryobi 2075r - page 6
6 • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate unit as a trimmer without string guard in place. Keep away fr om rotating cutter . • IGNITION SWITCH ON / ST ART / RUN • IGNITION SWITCH OFF or STOP • HOT SURF ACE WARNING Do not touch a hot muffler , gear box or cylinder . Y ou may get burned. These p ...
-
Ryobi 2075r - page 7
ASSEMBL Y INSTRUCTIONS 7 INST ALLING AND ADJUSTING THE LOOP HANDLE If the loop handle is not assembled on this model, use the following instructions: 1. Place the loop handle and bottom handle clamp on the boom shaft (Fig. 1). 2. Install, one at a time , the four (4) screws and four (4) hex nuts with a Phillips screwdriver . NOTE: Install all four ...
-
Ryobi 2075r - page 8
8 OIL AND FUEL INFORMA TION Old or improperly mixed fuel ar e usually the main reasons for the unit not running properly . Be sure to use fr esh, clean fuel and follow the instructions carefully for the pr oper fuel/oil mixture. NOTE: Alcohol-blended fuel absorbs moisture (water). As little as 1% moisture in the fuel can cause fuel and oil to separ ...
-
Ryobi 2075r - page 9
9 OPERA TING INSTRUCTIONS Fig. 6 1. MIX OIL WITH GAS AND FILL FUEL T ANK WITH FUEL/OIL MIXTURE per instructions on page 8. 2. Put the IGNITION SWITCH IN THE “ ON ” POSITION (Fig. 5). 3. FULL Y PRESS AND RELEASE THE PRIMER BULB 5 TO 7 TIMES. FUEL SHOULD BE VISIBLE IN THE BULB (Fig. 6). 4. PLACE THE CHOKE LEVER IN THE “ ST ART ” POSITION (A) ...
-
Ryobi 2075r - page 10
10 OPERA TING INSTRUCTIONS OPERA TING THE CLICK-LINK SYSTEM This unit is equipped with a Click-Link ® System, which enables optional attachments to be installed on the unit. The optional attachments are: Blower/V acuum. . . . . . . . . . . . . . . . . . . . . BV720r Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . GC720r Edger . . . . ...
-
Ryobi 2075r - page 11
11 OPERA TING INSTRUCTIONS CAUTION: Do not remove or alter the line cutting blade assembly . Excessive line length will cause clutch to overheat and may result in serious personal injury . Fig. 12 Each time the head is bumped, about 1 inch (25.4 mm) of trimming line is released. A blade in the string guard will cut the line to the pr oper length if ...
-
Ryobi 2075r - page 12
MAINTENANCE AND REP AIR INSTRUCTIONS 12 Fig. 15 3. Insert the line into the locking hole (Fig. 15) no more than 1/2 inch (12.7 mm). Do not push the line too far into the inner reel. A small loop is formed when the line is inserted correctly (Fig. 15). Locking Hole 4. Pull the line away from the spool until the line is tight against the inner reel ( ...
-
Ryobi 2075r - page 13
MAINTENANCE AND REP AIR INSTRUCTIONS 13 Fig. 18 Fig. 19 Fig. 17 5. Repeat the procedur e with the second eyelet and use the same amount of line as specified in Step 2. 6. Wind the inner reel counter clockwise until approximately four (4) inches of line r emains outside of the eyelets in the outer spool (Fig. 17). 7. If winding the line becomes diff ...
-
Ryobi 2075r - page 14
MAINTENANCE AND REP AIR INSTRUCTIONS 14 3. W ash the filter in detergent and water (Fig. 26). Rinse the filter thoroughly and allow it to dry . Fig. 26 Air Filter Fig. 24 2. Remove the air filter (Fig. 25). Fig. 25 AIR FIL TER MAINTENANCE CLEAN AND RE-OIL THE AIR FIL TER EVERY 10 HOURS OF OPERA TION. Y our unit ’ s air filter is one of the most i ...
-
Ryobi 2075r - page 15
MAINTENANCE AND REP AIR INSTRUCTIONS 15 6. Reinstall the filter (Fig. 25) and air filter cover . NOTE: If the unit is operated without the carburetor/air filter cover assembled, you will VOID the warranty . The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict the air flow , which upsets the fue ...
-
Ryobi 2075r - page 16
16 0.025 inch (0.655 mm) CAUTION: Replace a cracked, fouled or dirty spark plug. Do not sand blast, scrape, or clean electrodes because the engine could be damaged by grit entering the cylinde r. REPLACING THE SP ARK PLUG Use a Champion RCJ-6Y spark plug (or equivalent). Correct air gap is 0.025 in. (0.655 mm) . Remove plug after every 50 hours of ...
-
Ryobi 2075r - page 17
17 TROUBLESHOOTING If further assistance is requir ed, contact your authorized service dealer . PROBLEM CAUSE ACTION Engine will not start Fouled spark plug Engine will not idle Engine will not accelerate Engine lacks power or stalls when cutting Cutting head will not advance line Ignition switch is “ OFF ” Empty fuel tank Primer bulb wasn&apos ...
-
Ryobi 2075r - page 18
18 SPECIFICA TIONS DRIVE SHAFT & CUTTING HEAD Drive Shaft Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum T ube (Click-Link) Throttle Contr ol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Finger -Tip T rig ger Operating W eight . . . . . . . . . . . . ...
-
Ryobi 2075r - page 19
19 The California Air Resources Board and Ryobi Outdoor Products (ROP), is pleased to explain the emission control system warranty on your 1995 and later lawn and garden equipment engine. In California, new lawn and garden equipment engines must be designed, built and equipped to meet the State's stringent anti-smog standards. ROP must warrant ...
-
Ryobi 2075r - page 20
R YOBI OUTDOOR PRODUCTS warrants each new R YOBI Product for two (2) years according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of original retail purchase. Any part of the R YOBI Product manufactured or supplied by R YOBI and found in the reasonable judgement of R YOBI to be defect ...
Haben Sie eine Frage bezüglich Ryobi 2075r?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ryobi 2075r nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ryobi 2075r hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.