Deutsch dropdown-ico

Bedienungsanleitung Core Gamer AX-900

28 Seiten 0.93 mb
Download

Zur Seite of 28

Summary
  • Core Gamer AX-900 - page 1

    128-6996A 1 of 28 Model AX-900 Installation Manual RY SELECT ABLE FEA TURES Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual. RF Programmable Features : Fea ...

  • Core Gamer AX-900 - page 2

    128-6996A 2 of 28 This Page Intentionally Left Blank 2 ...

  • Core Gamer AX-900 - page 3

    128-6996A 3 of 28 Eighth Press and release the valet switch 1 chirp = siren and horn output Press transmitter Lock button to change 2 chirps = siren output only Press transmitter lock button to change 3 chirps = horn output only or Ninth Press and release the valet switch 2 chirps = horn chirp output 16mS Press transmitter Lock button to change 3 c ...

  • Core Gamer AX-900 - page 4

    128-6996A 4 of 28 HOOD AND TRUNK PIN SWITCHES: The pin switches included in this package are intended for protecting the hood and trunk areas of the vehicle. In all cases, the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood/trunk open), it will supply a ground to the input wire activating the alarm. In ad ...

  • Core Gamer AX-900 - page 5

    128-6996A 5 of 28 CONTROL SWITCH: Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick panel, or glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch, and also that the drill will not penetrate any existing factory wirin ...

  • Core Gamer AX-900 - page 6

    128-6996A 6 of 28 PURPLE Wire: S t arter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear . Underst anding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method ...

  • Core Gamer AX-900 - page 7

    128-6996A 7 of 28 WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red T race Wire: Parking Light Flasher Feed This wire is the common contact of the on board p arking light flasher relay . If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) NOTE: ...

  • Core Gamer AX-900 - page 8

    128-6996A 8 of 28 Brown Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the Brown wire to the Red wire of the Siren. Secure the Black wire of the Siren to a known chassis ground or solid clean metal surface. Siren Wiring Detail 8 Parking Light Wiring Detai ...

  • Core Gamer AX-900 - page 9

    128-6996A 9 of 28 Blue Wire: (-) Instant Trigger Input This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches previously installed. Note: This wire will be shunted when remote control channel 2 is accessed, (trunk release). This wire will remain shunted all the while there is ground present ...

  • Core Gamer AX-900 - page 10

    128-6996A 10 of 28 10 Black w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay and wired to t ...

  • Core Gamer AX-900 - page 11

    128-6996A 11 of 28 Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when ...

  • Core Gamer AX-900 - page 12

    128-6996A 12 of 28 12 Purple w/ White T race Wire: T achometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote S tart module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignit ...

  • Core Gamer AX-900 - page 13

    128-6996A 13 of 28 Red w/ White T race Wire: T runk Pop Delayed 300mA Pulsed Channel 2 Output This wire supplies a 300mA ground pulsed output whenever channel two of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must be connected to a relay to sup ...

  • Core Gamer AX-900 - page 14

    128-6996A 14 of 28 14 White w/ Blue T race Wire: 300mA Pulsed or Latched Channel 4 Output This wire supplies a 300 mA switched output whenever channel four of the receiver is accessed. Pressing the pre-programmed transmitter button(s) will access channel four and will remain active, for up to 8 seconds, as long as the transmitter button(s) is held. ...

  • Core Gamer AX-900 - page 15

    128-6996A 15 of 28 15 W ARNING: Connecting the light blue/black to the high current circuits, will damage the control module. Connect the light blue/black wire to terminal 86 of the AS - 9256 relay (or equivalent 30 A automotive relay), and wire the remaining relay contacts to perform the selected function of channel 7. Grey w/Black T race Wire: DI ...

  • Core Gamer AX-900 - page 16

    128-6996A 16 of 28 16 4 Pin Upgrade T elematic Module: Red = + 5 V olt s / Black = Ground / White = Dat a TX / Y ellow = Data RX Connect the 4 pin harness found in the T elematic one way module kit to the mating port on the PTUGM. NOTE: If using the TWO W A Y T elematic module, only Ground, TX, and RX are used on this port, the + 12 volt supply for ...

  • Core Gamer AX-900 - page 17

    128-6996A 17 of 28 3 Wire Positive Switched Door Locks: In this application, the Green wire of the door lock harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Green wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay . The Blue ...

  • Core Gamer AX-900 - page 18

    128-6996A 18 of 28 18 3 Wire Positive Switched 2 Step Door Locks The Blue wire provides a positive pulse during arming or the pulsed + 12 volt lock output. Connect the blue wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay . The Green wire provides the first positiv ...

  • Core Gamer AX-900 - page 19

    128-6996A 19 of 28 19 Note: Resistive Circuit s, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, and or fixed resistors. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for in ...

  • Core Gamer AX-900 - page 20

    128-6996A 20 of 28 20 REMOTE ST ART SELECT ABLE FEA TURES Feature Lts Flash 1X Lts Flash 2X Lts Flash 3X Lts Flash 4X Default LED Pattern 1 RF S tart Chirp O f f On On 1X Pause,etc... 2 Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min 2X Pause,etc... 3 Park Lights On Steady Flash S teady 3X Pause,etc... 4 Input Check V oltage T ach T ac h 4X Pause,et ...

  • Core Gamer AX-900 - page 21

    128-6996A 21 of 28 NOTE: If the unit fails to learn tach rate due to an improper tachometer connection or a poor tach source, the parking lights will not flash. T o correct this situation, locate and connect the Purple/White wire to the proper tach signal, and then repeat the tach learn routine. Diagnostics: Enter selectable feature #7 and turn on ...

  • Core Gamer AX-900 - page 22

    128-6996A 22 of 28 22 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed af ter the installation of an Audiovox Remote S tart Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. ...

  • Core Gamer AX-900 - page 23

    128-6996A 23 of 28 CAUTION! REMEMBER TO RECONNECT THE BROWN/RED WIRE TEMPORARIL Y DISCONNECTED IN STEP 3 DO NOT RELEASE THIS VEHICLE T O THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE NEUTRAL SAFETY ST ART FEA TURE. 23 The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you ...

  • Core Gamer AX-900 - page 24

    128-6996A 24 of 28 24 T o connect to the key in sensor as shown in method 1: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. ...

  • Core Gamer AX-900 - page 25

    128-6996A 25 of 28 25 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the igni ...

  • Core Gamer AX-900 - page 26

    128-6996A 26 of 28 5. Check the vehicle's wipers, lights, horn, etc.... to insure proper operation. 6. Replace all panels that were removed during installation, and retest the system. 7. Explain all activated features and safety systems associated with Remote S tart Unit inst alled to the customer . 8. Place the V alet Switch T ag and or the R ...

  • Core Gamer AX-900 - page 27

    128-6996A 27 of 28 27 ...

  • Core Gamer AX-900 - page 28

    128-6996A 28 of 28 © 2004 Audiovox Electronics Corp., Hauppauge, NY 11788 128-6996A WWW .audi ovox .com For Customer Service Visit Our Website At Product Infor mation, Ph otos, F AQ’s Owner ’ s Manual s 28 ...

Produzent Core Gamer Kategorie Automobile Accessories

Dokumente, die wir vom Produzenten des Geräts Core Gamer AX-900 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Core Gamer
- Bedienungsanleitungen AX-900
- Produktkarten Core Gamer
- Informationsbroschüren
- oder Energieetiketten Core Gamer AX-900
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Core Gamer AX-900.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Core Gamer AX-900, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Core Gamer AX-900. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Core Gamer AX-900 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Core Gamer AX-900, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Core Gamer AX-900 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Core Gamer AX-900 verständlich ist.

Eine gänzliche Bedienungsanleitung von Core Gamer sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Core Gamer AX-900 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Core Gamer AX-900 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Core Gamer AX-900, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Core Gamer AX-900 - die uns die ersten Schritte während der Nutzung von Core Gamer AX-900 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Core Gamer AX-900 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Core Gamer AX-900 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Core Gamer AX-900?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Core Gamer AX-900 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Core Gamer AX-900 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (1)

SERGIO CAMARGO

NUESTRO EQUIPO ESTA PIDIENDO CON CADA VENTA CIERRE DE LOTE PORQUE SUPUESTAMENTE LA MEMORIA ESTA LLENA, QUE DEBO HACER PARA LIBERAR LA MEMORIA Y DEJE DE PEDIRME CIERRE DE LOTE CON CADA VENTA.