Bedienungsanleitung Outback Power Systems 500

24 Seiten 3.6 mb
Download

Zur Seite of 24

Summary
  • Outback Power Systems 500 - page 1

    500 U ser ’ s Guide Includes Mounting, Installation, and Pr oduct Registration ...

  • Outback Power Systems 500 - page 2

    OutBack P ower Systems FLEXwar e is a system of modular aluminum mounting hardware and installation components designed for con venient system installation and integration. About OutBack P ower Sy stems OutBack P ower Systems is a leader in advanced energy con version technology . Our products include true sine wave inv er ter/chargers , a maximum ...

  • Outback Power Systems 500 - page 3

    Requirements and W ar nings The OutBack FLEXwar e 500 enclosures (FW500-AC and FW500-DC) are listed by ETL as indoor enclosures to UL standar d UL 508A Industr ial Control P anels. This enclosure is intended f or battery circuits congured for 12 to 48 v olts nominal. Grounding Instructions – Each enclosure should be connected to a grounded , p ...

  • Outback Power Systems 500 - page 4

    W elcome to OutBack P ower S ystems ’ FLEX ware FLEXware is a con venient all-aluminum power system o ering simpler , code - compliant installation of OutBack power electronics components . Three versions of FLEX ware are a vailable: • FLEXware 250 f or single FX Series I nverter/Charger installations along with the desired A C and DC discon ...

  • Outback Power Systems 500 - page 5

    HUB MX60s Figur e 1: Complete FLEXwar e 500 System installed (vertical installation is acceptable when mounting space is limited) Note: Although FLEXwar e 500 suppor ts two MX Charge Controllers , both locations—top and side —are shown in F igure 1. Getting to Know FLEXw are 500 IOB Kit FW500-AC FW Mounting Plate DC Breakers MX60 DC FW500-DC Di ...

  • Outback Power Systems 500 - page 6

    F ront View Side View Figur e 2 Knockouts and Dimensions 11.40 18.27 12.06 3 ...

  • Outback Power Systems 500 - page 7

    A complete FLEXwar e 500 System consists of the following in addition t o the FW500-AC and FW500-DC: • FLEXware Mounting Plat e (FW-MP) • two FX Series I nverter/Chargers • AC Conduit A dapter (ACA) and a DC Conduit A dapter (DCA), which connect each FX to the FW500-AC and FW500-DC • MX Charge Contr oller(s) (normally par t of this system) ...

  • Outback Power Systems 500 - page 8

    Installation Tips • Never use less than the minimum recommended number and type of fasteners when installing the FLEXware Mounting Plat es. • Each FX weighs in excess of 50 lbs and is often mor e easily installed by two people rather than one. • Be sure the DC enclosure is secur ed to the FLEXware Mounting Plat e before attaching the MX Charg ...

  • Outback Power Systems 500 - page 9

    Figur e 4: F irst FX installed With the Mounting Plate and the hanging screws (f or the FX Inverter/Chargers) inser ted, install the FXs. • Star t with the top FX. • Hang the FX on the hanging screws , but continue to hold onto it. • Loosely install f our M6 X 20 mm screws, included with the FW -MP , one in each corner ; tighten them when all ...

  • Outback Power Systems 500 - page 10

    After the FXs are installed , mount the AC chassis and the DC chassis in either order . Note: It is easier to remove the appropriate side knock outs from both the AC and DC chassis befor e installing either of them. If needed, the back knock outs must be removed befor e installation. Figur e 6: Removing chassis side knock outs When installing the A ...

  • Outback Power Systems 500 - page 11

    Installation of the AC Chassis and DC Chassis T o install the chassis: • Hold each chassis up to its respective mounting holes on the FW-MP . • Place one M6 X 10mm machine screw (pr ovided with the FW-MP) in each corner , tightening only enough to keep the chassis in place. AC side DC side Figur e 7: Chassis Mounting Holes AC Chassis Mounting H ...

  • Outback Power Systems 500 - page 12

    Clear plastic AC cover AC Conduit Plat e Figur e 9: FX Series I nverter/Charger DC Wiring Cover (DC C) Figur e 8: AC and DC chassis mounted With each chassis loosely mounted , the AC Conduit Adapt er (ACA) and DC Conduit Adapt er (DCA) are installed on each FX. • Remove the clear plastic AC cov er and AC Conduit Plat e from each FX. Corrugated Co ...

  • Outback Power Systems 500 - page 13

    • Line up either the ACA or DCA on its respective side of the FX, starting at the top. • T o attach a DCA, line up its t wo screw holes with the upper and low er right DCC screw holes. • When lined up, loosely install the upper scr ew to hold the DCA in place. • Slide the DC chassis over snug against the DCA (the scr ew slots in each chassi ...

  • Outback Power Systems 500 - page 14

    Plastic bushing, DC side Figur e 11: DCA bushing Note: The DCA will be held rmly in place when the DCC (FX cover) is secured at the end of the installation. T o install an ACA: • F ollow the separate ACA instructions f or mounting to the FX. • Line each ACA up with its conduit hole in the AC chassis . • When aligned, mo ve the AC chassis s ...

  • Outback Power Systems 500 - page 15

    F igure 12: ACAs installed With both the AC Chassis and DC Chassis installed , the breaker brackets, AC din rail(s), and optional AC and DC breakers can be installed. P lease see the individual Input/Output/B ypass Breaker (IOB) kit for instructions. Each ACA ts against the AC chassis 13 ...

  • Outback Power Systems 500 - page 16

    MX60 Installation A FLEXware 500 Syst em will normally have up to two MX Charge Contr ollers installed on the FW500-DC. The chassis accommodates both side and top installation. Newer MXs have r ear knock outs allowing them to be mounted dir ectly to the side of the enclosure without the need for additional mounting brackets. Mounting brackets are a ...

  • Outback Power Systems 500 - page 17

    The MX Charge Contr oller attaches to the chassis using three #10 X 3/8” sheet metal screws included in the hardware kit. Two ar e inser ted from inside the MX and the third through the hanger on the top of the MX. MX Knockouts Figur e 13: MX Charge Contr oller 1” knock outs Charge Controller knock outs 15 ...

  • Outback Power Systems 500 - page 18

    Installing an OutBack HUB An OutBack HUB allows the FX Series Inver ter/Chargers , MX60 Charge Controllers , and MA TE to communicate with each other . I t attaches to the outside of the FW500-AC (har dware included with the HUB). Figur e 14: OutBack HUB HUB connection 16 ...

  • Outback Power Systems 500 - page 19

    Figur e 15: Wiring Diagram 17 ...

  • Outback Power Systems 500 - page 20

    ...

  • Outback Power Systems 500 - page 21

    ...

  • Outback Power Systems 500 - page 22

    ...

  • Outback Power Systems 500 - page 23

    Pr oduct Registration Please take a moment to regist er and provide us with some important information. Send to: OutBack P ower Systems , 19009 62nd Avenue NE, Arlington, W A 98223 USA. Name: ����������������������������������������������������? ...

  • Outback Power Systems 500 - page 24

    European Sales Office Barcelona, España (+34) 600-843-845 19009 62nd A venue NE Arlington, W A USA (+1) 360-435-6030 www .outback power .com 900-0061-1 ...

Produzent Outback Power Systems Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Outback Power Systems 500 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Outback Power Systems
- Bedienungsanleitungen 500
- Produktkarten Outback Power Systems
- Informationsbroschüren
- oder Energieetiketten Outback Power Systems 500
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Outback Power Systems 500.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Outback Power Systems 500, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Outback Power Systems 500. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Outback Power Systems 500 ansehen.

Die komplette Bedienungsanleitung des Geräts Outback Power Systems 500, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Outback Power Systems 500 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Outback Power Systems 500 verständlich ist.

Eine gänzliche Bedienungsanleitung von Outback Power Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Outback Power Systems 500 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Outback Power Systems 500 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Outback Power Systems 500, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Outback Power Systems 500 - die uns die ersten Schritte während der Nutzung von Outback Power Systems 500 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Outback Power Systems 500 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Outback Power Systems 500 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Outback Power Systems 500?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Outback Power Systems 500 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Outback Power Systems 500 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)