-
Patton electronic 2156 - page 1
USER MANUAL MODELS 2156 & 2157 CopperLink Ethernet Extender s SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2156_2157 Doc# 032131U Rev . A Revised 2/4/03 An ISO-9001Cer tified Company ...
-
Patton electronic 2156 - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 3 1.1 Radio and TV Interference ............................................................ 3 1.2 CE Notice ...................................................................................... 3 1.3 FCC Part 68 .................................. ...
-
Patton electronic 2156 - page 3
3 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2156 or 2157 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or mater ials , and does not cov er customer damage, ...
-
Patton electronic 2156 - page 4
4 1.3 FCC PART 68 1. Y ou are required to request service from the telephone company bef ore you connect the Model 2156 or 2157 to a netw ork. When you request ser vice , y ou must pro vide the telephone compan y with the f ollo wing data. — The required Universal Service Order code (USOC) jack: RJ-11C — The make , model number , Ringer Equival ...
-
Patton electronic 2156 - page 5
5 1.4 INDUSTRY CANADA NOTICE NO TICE: This equipment meets the applicable Industry Canada T ermi- nal Equipment T echnical Specifications. This is confirmed by the registr a- tion number . The abbre viation IC , bef ore the registration number signifies that registration was perf ormed based on a Declaration of conformity indicating that Industr ...
-
Patton electronic 2156 - page 6
6 2.0 GENERAL INFORMATION Thank you purchasing this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one y ear for par ts and labor . If questions ar ise while installing or using this product, contact T echnical Support at +1 (301) 975-1007 . 2.1 FEATURES • Easy-to-install Ethernet Extender ...
-
Patton electronic 2156 - page 7
7 Figure 1. T ypical application The 2157/L and 2157/R work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. ...
-
Patton electronic 2156 - page 8
8 3.0 INSTALLATION Because the CopperLink Ethernet Extenders require no configuration, they can be installed quickly . Installation consists of the f ollo wing: • Connect the line interf ace between the units (refer to section 3.1, “Connecting the T wisted-P air Line Interf ace” on page 8) Note See Figure 2 for the rear-panel connectors loca ...
-
Patton electronic 2156 - page 9
9 F ollow the steps below to connect the CopperLink interf aces. Note The Model 2156 or 2157 units work in pairs. One of the units must be a Model 2156/L (local) or 2157/L, and the other unit must be a Model 2156/R (remote) or 2157/R. 1. T o function proper ly , the two Ethernet Extenders must be connected together using twisted-pair , unconditione ...
-
Patton electronic 2156 - page 10
10 Figure 4. CopperLink Ethernet Extender 10/100Base-T RJ-45 Connector Pinout. Connecting the 10/100Base-T Ethernet P ort to a Hub or PC The Models 2156 and 2157 are equipped with an MDI-X s witch that enables connections to a hub (DCE) or PC (DTE) interf ace, thereb y elimininating confusion ov er whether a straight-through or crossov er cable is ...
-
Patton electronic 2156 - page 11
11 Figure 7. MDI-X switch pressed in perf orms 10/100Base-T crossover function 3.3 CONNECTING POWER An e xter nal A C or DC power supply is a vailab le separately . This connec- tion is made via the barrel jack on the rear panel of the Models 2156 and 2157. No configuration is necessary for the po wer supply (See Appendix B on page 18 f or domesti ...
-
Patton electronic 2156 - page 12
12 External 48 VDC power supply • Input – Rated voltage: 36–60 VDC – Rated current: 0.25 A DC at nominal 48 VDC – 3-pin locking connector , 3.5 mm pitch – Reverse polarity protection – T ransient over -voltage pr otection, 100 VDC at 2 ms • Output – Rated voltage: 5 VDC ± 5%, 5W – Rated current; 1 A DC – 6-inch cable terminat ...
-
Patton electronic 2156 - page 13
13 3.5 CONSOLE PORT The Console P or t is only intended f or use by P atton Electronics T echnical Suppor t technicians. ...
-
Patton electronic 2156 - page 14
14 4.0 OPERATION Once the CopperLink Ethernet Extenders are proper ly installed, the y should operate transparently . No user settings required. This section describes reading the LED status monitors. 4.1 FRONT PANEL LED STATUS MONITORS The Models 2156 and 2157 f eature eight front-panel LEDs that monitor power , Ether net signals, and the CopperLi ...
-
Patton electronic 2156 - page 15
15 APPENDIX A SPECIFICATIONS A.1 GENERAL CHARACTERISTICS • Compact low cost plug-and-pla y router • 10/100 Ethernet • Unlimited host suppor t • Eight front panel LEDs indicate P o wer , W AN, Ether net LAN speed and status • Conv enient and standard RJ connectors f or Ether net and line • External UI or 48 VDC po wer supply options • ...
-
Patton electronic 2156 - page 16
16 A.4 EXTENSION DISTANCE AND RATE • 2.3 Mbps (Model 2156) or 4.6 Mbps speed (Model 2157) • Distances up to 30,000 ft (9,144 m) on 24 A WG (0.4 mm) wire • A uto-adjusting rate picks best rate f or a giv en extension distance (see tables belo w) T able 2: Model 2156 Extension Distances DSL line rate No Noise 26g (0.4 mm) 24g (0.5 mm) 22g (0.6 ...
-
Patton electronic 2156 - page 17
17 A.5 LED INDICATORS • Eight LED indicators •P o w e r • W AN Link, T ransmit, and Receiv e • Ethernet Link, 100M, T ransmit, and Receive A.6 POWER AND POWER SUPPLY SPECIFICATIONS • Either A C or DC options are av ailable • Connection to the CopperLink Ethernet Extender requires +5VDC ±5% DC power (1.0A minim um). Center pin is +5V . ...
-
Patton electronic 2156 - page 18
18 APPENDIX B MODELS 2156 AND 2157 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) P atton Model # Description 2156 Base Models 2156/L CopperLink Ethernet Extender ; Line: RJ-11 (Local) 2156/R CopperLink Ethernet Extender ; Line: RJ-11 (Remote) 2156-2PK CopperLink Ethernet Extender Kit: ...
-
Patton electronic 2156 - page 19
19 APPENDIX C MODELS 2156 AND 2157 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-11 • Pin 2: RING • Pin 3: TIP • Pins 1 & 4: no connection ...
-
Patton electronic 2156 - page 20
20 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ...
Haben Sie eine Frage bezüglich Patton electronic 2156?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Patton electronic 2156 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Patton electronic 2156 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.