Bedienungsanleitung Simplicity 1691620

20 Seiten 0.35 mb
Download

Zur Seite of 20

Summary
  • Simplicity 1691620 - page 1

    A TT ACHMENT OPERA T OR’S MANUAL Snow Plow/Dozer Blade Mfg. No. Description 1691520 42” Snow Plow/Dozer Blade Hitch Mfg. No. Description 1692039 Hitch (for Landlord / 1700 / 2700 Series & Broadmoor / 1600 / 2600 Series) 1692624 Hitch (for Regent / 500 / 2500 Series) 1715046-02 Rev 10/97 TP 100-2122-02-AT-SMA Snow/Dozer Blade & Hitch ...

  • Simplicity 1691620 - page 2

    ...

  • Simplicity 1691620 - page 3

    1 Recommended Accessories ...................................................................................................................................1 Safety Rules .............................................................................................................................................................2 Components ........ ...

  • Simplicity 1691620 - page 4

    2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The tri- angle in the text signifies important cautions or warnings which must be followed. General • Read the operator’s manual carefull ...

  • Simplicity 1691620 - page 5

    3 Components A. Blade Assembly B. I.D. Plate C. Hex Nut, 5/16-18 (4) D. Eyebolt (2) E. Tension Spring (2) F. Pivot Frame Assembly G. Hex Lock Nut, 1/2-13 (2) H. Spacer (2) I. Hex Capscrew, 1/2-13 x 1 (2) J. Shoe Assembly (2) K. Plain Washer, 3/8 (4) L. Lockwasher, 3/8 (10) M. Hex Head Capscrew, 3/8-16 x 3/4 (4) N. Wear Plate O. Hex Nut, 3/8-16 P. C ...

  • Simplicity 1691620 - page 6

    4 Components Broadmoor/L T/1600/2600, & Landlord/GT/1700/2700 Series Parts Figure 2. Mfg. No. 1692039 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 1/2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod, (Manual or Electric Lift) F. Clip, Spring (Qty. 3) G. King Pin H. Push Bar Assembly I. Safety Clip (Qty. 2) ...

  • Simplicity 1691620 - page 7

    5 Components Figure 3A. Mfg. No. 1692624 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod F. Spring Clip (Qty. 3) G. Clevis Pin, 3/8 (Qty. 2) H. Push Bar Assembly I. Hitch Pin J. Plain Washer 5/16 K. Safety Clip L. Chain M. Spring N. Pivot Pin I J K M L N Regent/500 ...

  • Simplicity 1691620 - page 8

    6 Components Figure 3B. Mfg. No. 1692624 Hitch Assembly A. Hitch Assy. B. Rear Support Assy. C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) H. Rod I. Spring Assist Bracket J. Capscrew, 3/8-16 x 2 K. Spacer, 25/64 x 5/8 x 17/64 L. Spacer, 13/32 x 1 x 13/16 M. Nut, Whizlock, 3/8-16 N. Lockwashe ...

  • Simplicity 1691620 - page 9

    7 Assembly All Models 1. Place the blade on a flat surface. 2. Regent/500/2500 & Broadmoor/LT/1600/2600 Series: See Figure 4. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B). Do not install second bar stop. Landlord/GT/1700/2700 Series: Do not install bar stops. Figure 4. Bar Stop A. Bar Stop B. Taptite Screw, 5/16-18 x 1 ...

  • Simplicity 1691620 - page 10

    NOTE: On single cylinder tractors, clevis pin (B, Figure 6) must be installed to bracket before mount- ing bracket on tractor frame. NOTE: Spring-assist bracket (A, Figure 6) does not need to be installed on units with electric lift. Broadmoor/L T/1600/2600 Series & Landlord/GT/1700/2700 Series Only: 7. See Figure 6. Install the spring-assist b ...

  • Simplicity 1691620 - page 11

    9 Regent/500/2500 Series Only: 1. Increase front tire pressure to 20 psi (138 kPa) to compensate for added weight of the hitch, plus bar and blade. Be sure both tires have equal pressure. 2. From the front of tractor, slide the hitch under the tractor so that the hitch bar is positioned at the front of the unit. 3. See Figure 8. Turn the wheels ful ...

  • Simplicity 1691620 - page 12

    10 Installation Figure 10. A. Push Bar Hitch C. Hitch Pin B. Frame Bracket D. Safety Clip Broadmoor/L T/1600/2600 Series & Landlord/GT/1700/2700 Series 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. See Figure 10. Position the push bar hitch (A) into the t ...

  • Simplicity 1691620 - page 13

    11 Installation All Models 4. See Figure 12. Raise the push bar and attach the spring (A) to the push bar bracket and the open end link of the 4-link spring assist chain. Figure 12. A. Spring Figure 13. Dozer Blade Assembled and Installed A. Push Bar D. Spring Clip B. Pivot Frame E. Pivot Pin C. King Pin 5. See Figure 13. Insert front of push bar ( ...

  • Simplicity 1691620 - page 14

    NOTE: Two lift rods are packaged with the Broadmoor/LT/1600/2600 & Landlord/GT/1700/2700 hitch assembly. Use the correct lift rod for manual or electric lift as shown in Figure 2. 7. Assemble lift rod per Figure 2 or 3. 8. See Figure 14. Insert prong of rod guide (A) through hole in upright of push bar (B), and secure with spring clip (C). 9. E ...

  • Simplicity 1691620 - page 15

    13 Removal 1. Lower the blade. 2. Remove blade and lift rod from push bar. 3. Raise push bar and unhook the spring from the chain. Remove the chain from the frame bracket. Reinstall safety clip to clevis pin. 4. Disconnect the lift rod from the lift lever on tractor by removing the spring clip. Set tractor speed to obtain the needed power to move t ...

  • Simplicity 1691620 - page 16

    Lift Rod See Figure 17. For initial setting, place front set collar (A) one inch from rod guide with blade fully lowered. Place rear set collar (B) against spring (C). Tighten the setscrews in the two set collars.To adjust, perform the following: 1. Fully raise the blade by pulling back on the tractor lift lever. Measure distance between scraper ba ...

  • Simplicity 1691620 - page 17

    15 Adjustments Spring T ension See Figure 19. This snow plow/dozer blade is spring loaded so that when the blade strikes a solid object, the springs will allow the blade to release as shown, rather than cause damage. The blade will go back to its original position after object is cleared. Figure 19. Dozer Blade “Released” Figure 20. Tension Spr ...

  • Simplicity 1691620 - page 18

    16 T orque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8.6 ...

  • Simplicity 1691620 - page 19

    ...

  • Simplicity 1691620 - page 20

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 1997 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Produzent Simplicity Kategorie Snow Blower Attachment

Dokumente, die wir vom Produzenten des Geräts Simplicity 1691620 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Simplicity
- Bedienungsanleitungen 1691620
- Produktkarten Simplicity
- Informationsbroschüren
- oder Energieetiketten Simplicity 1691620
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Simplicity 1691620.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Simplicity 1691620, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Simplicity 1691620. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Simplicity 1691620 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Simplicity 1691620, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Simplicity 1691620 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Simplicity 1691620 verständlich ist.

Eine gänzliche Bedienungsanleitung von Simplicity sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Simplicity 1691620 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Simplicity 1691620 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Simplicity 1691620, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Simplicity 1691620 - die uns die ersten Schritte während der Nutzung von Simplicity 1691620 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Simplicity 1691620 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Simplicity 1691620 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Simplicity 1691620?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Simplicity 1691620 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Simplicity 1691620 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)