Bedienungsanleitung Moog Videolarm WS6-50NF-X2

12 Seiten Betrifft nicht
Download

Zur Seite of 12

Summary
  • Moog Videolarm WS6-50NF-X2 - page 1

    P R O D U C T I N S T R U C T I O N S INST ALLA TION PREP ARA TION INST ALLA TION PREP ARA TION 1. Choose an appropriate corner location. The WS6 can be mounted at any height in a corner . 2. Complete all wire and conduit runs prior to installation of the housing. REVISION DA TE: 11-11-2010 Depending on the voltage being used, refer to one of the f ...

  • Moog Videolarm WS6-50NF-X2 - page 2

    - 2 - CAMERA BRACKET SE TUP 8. T o adjust the camera bracket, loosen the two thumb screws (Figure 6). When the desired focus and location are achieved tighten the thumb screws on the brackets in place using needle nose pliers. Use Loctite™ or equivalent to secure the screws, especially in installations where vibration is a concern. Figure 3 1. Co ...

  • Moog Videolarm WS6-50NF-X2 - page 3

    - 3 - Figure 7 CAMERA FOCUSING (Figur e 7) 1. The camera is factory equipped with a 3.6mm xed lens. A 2.5mm lens is also provided. T o remove the 3.6mm lens, loosen the set screw and unscrew the lens counter-clockwise. 2. Fine focusing of the lens: Loosen the set screw in the lens mount and manually rotate the lens until a clear picture is achie ...

  • Moog Videolarm WS6-50NF-X2 - page 4

    - 4 - WINDOW GU ARD™ P AINT SHIELD REPLACEMENT Y our W arrior 6 comes with a replaceable Window Guard™ paint shield to protect the front plate window from vandalism. If vandalism occurs (spray paint, scratches, etc.) you need only replace the shield, not the entire window . Additional shields can be ordered. T o replace the shield, use the foll ...

  • Moog Videolarm WS6-50NF-X2 - page 5

    2 50 f t  3  4  5  8  13  W 3 00 f t  4  5  6  10  16  W 4 00 f t  5  6  8  13  21  W 5 00 f t  6  8  10  16  26  W 6 00 f t  8  10  12  19  31  W 8 00 f t  10  13  16  25  42  W 1 0 0 0 ft  13  16  20  32  52  W 1 2 5 0 ft ...

  • Moog Videolarm WS6-50NF-X2 - page 6

    - 6 - IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS UNPACKING SERVICE 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 Cable ...

  • Moog Videolarm WS6-50NF-X2 - page 7

    6 5 4 3 2 1 WS6 - Exploded Diagram and Replacement P ar ts List P ar t Number Description 1 RPWS6010 W ARRIOR 6 F ACE PLA TE F ASTENER KIT 2 RPWS6020 W ARRIOR 6 FRONT PLA TE ASSEMBL Y 3 WS6PS W ARRIOR 6 REPLACEMENT P AINT SHIELD 4 RPWS6040 W ARRIOR 6 REPLACEMENT WINDOW KIT NTSC BOARD CAMERAS 5 RPWS6050 W ARRIOR 6 ST ANDARD RES, BLACK & WHITE, F ...

  • Moog Videolarm WS6-50NF-X2 - page 8

    P ower Supply P ower A P ower B Camera Assembly Primar y P ower Video Signal Video Shield Monitor - 8 - (Ground Return) Figure A Ground Loop TROUBLESHOO TING If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support. IMPORT ANT NOTE: If you h ...

  • Moog Videolarm WS6-50NF-X2 - page 9

    A C Vo l t m e t e r Camera Monitor Bridge Tap NV-213 A NV-213 A - 9 - NV T TROUBLESHOO TING If you a re experi encing p roblems , attempt to simpl ify your setup. T est each cable segment separate ly . For exa mple, te st the camera and monitor together with out the other equi pment. Then add in the NVT transce ivers, b ack-to-b ack. T es t each s ...

  • Moog Videolarm WS6-50NF-X2 - page 10

    - 10 - Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative): T otal current for a 12 VDC system: TO T AL CURRENT = (350mA x total number of cameras) Example: 350mA x 5 total cameras = 1750mA T otal current for a 24 V ...

  • Moog Videolarm WS6-50NF-X2 - page 11

    - 1 1 - LIMITED W ARR ANT Y FOR VIDEOLARM INC. PRODUC TS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows: PRODUCTCA TEGORY P ARTS LABOR All Enclosures and Electronics Five (5) Y ears Five (5) Y ears Pan/T ilts Three (3) Y ears **6 months if used in autoscan Three (3) Y ears **6 months if used in a ...

  • Moog Videolarm WS6-50NF-X2 - page 12

    - 12 - Pr oduct Registration / W arranty Thank you for choosing Videolarm. W e value your patronage and ar e solely committed to providing you with only the highest quality products available with unmatched customer service levels that ar e second- to-none in the security industry . Should a problem arise, r est assure that Videolarm stands behind ...

Produzent Moog Videolarm Kategorie Security camera

Dokumente, die wir vom Produzenten des Geräts Moog Videolarm WS6-50NF-X2 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Moog Videolarm
- Bedienungsanleitungen WS6-50NF-X2
- Produktkarten Moog Videolarm
- Informationsbroschüren
- oder Energieetiketten Moog Videolarm WS6-50NF-X2
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Moog Videolarm WS6-50NF-X2.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Moog Videolarm WS6-50NF-X2, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Moog Videolarm WS6-50NF-X2. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Moog Videolarm WS6-50NF-X2 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Moog Videolarm WS6-50NF-X2, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Moog Videolarm WS6-50NF-X2 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Moog Videolarm WS6-50NF-X2 verständlich ist.

Eine gänzliche Bedienungsanleitung von Moog Videolarm sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Moog Videolarm WS6-50NF-X2 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Moog Videolarm WS6-50NF-X2 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Moog Videolarm WS6-50NF-X2, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Moog Videolarm WS6-50NF-X2 - die uns die ersten Schritte während der Nutzung von Moog Videolarm WS6-50NF-X2 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Moog Videolarm WS6-50NF-X2 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Moog Videolarm WS6-50NF-X2 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Moog Videolarm WS6-50NF-X2?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Moog Videolarm WS6-50NF-X2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Moog Videolarm WS6-50NF-X2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)