Bedienungsanleitung Kenmore 153.31604

24 Seiten 1.06 mb
Download

Zur Seite of 24

Summary
  • Kenmore 153.31604 - page 1

    1 SA VE THIS MANUAL FOR FUTURE REFERENCE. Owner ’ s Manual FOR POT ABLE W A TER HEA TING ONL Y . NOT SUIT ABLE FOR SP ACE HEA TING. MODEL NO. 153.316040 6 GALLON 153.316050 10 GALLON 153.316060 19 GALLON SHORT 153.316070 19.9 GALLON T ALL 153.316331 30 GALLON 153.326060 19 GALLON 240 V . SHORT 153.326070 19.9 GALLON 240 V . T ALL 153.326331 30 GA ...

  • Kenmore 153.31604 - page 2

    2 SAFE INST ALLA TION, USE AND SERVICE Y our safety and the safety of others is extremely important in the installation, use and servicing of this water heater . Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and others of a potential injury hazard. Read and obey all safety m ...

  • Kenmore 153.31604 - page 3

    3 GENERAL SAFETY ...

  • Kenmore 153.31604 - page 4

    4 Thank Y ou for purchasing a Sears water heater . Properly installed and maintained, it should give you years of trouble free service. It is strongly suggested that this new water heater be professionally installed, contact the local Sears Service Center or any Sears store. They will arrange for prompt, quality installation by Sears authorized con ...

  • Kenmore 153.31604 - page 5

    5 PRODUCT SPECIFICA TIONS MAXIMUM FUSE RECOVER Y RA TE MINIMUM OR CIRCUIT MODEL IN GALLONS GALS.PER HOUR WIRE SIZE* BREAKER NUMBER (LITERS) DIA. HEIGHT @90 0 F Rise 120 V olt 240 V olt (GAUGE) SIZE (AMPS) 153.316040 6 (22.7) 14. 250 ” ( 362 ) 15. 375 ” ( 391 ) 7.5 1650 ---- 12 20 153.316050 10 (37.8) 16” (4 06) 18. 25” (4 64) 7.5 1650 ---- ...

  • Kenmore 153.31604 - page 6

    6 MA TERIALS AND BASIC TOOLS NEEDED Basic T ools Y ou may or may not need all of these tools, depending on your type of installation. These tools can be purchased at your local Sears store. Pipe Wrench (2) Screwdriver 6 Foot T ape or Folding Rule Garden Hose Drill Pipe Dope or T eon T ape Additional T ools Needed When Sweat Soldering T ubing Cut ...

  • Kenmore 153.31604 - page 7

    7 Removing the Old W ater Heater FIGURE 1. 1. Turn “OFF” electrical supply to the water heater . FIGURE 2. 2. T urn “OFF” the water supply to the water heater at the water shut-off valve or water meter . FIGURE 3. 3. Attach a hose to the water heater drain valve and put the other end in a oor drain or outdoors. Open the water heater drai ...

  • Kenmore 153.31604 - page 8

    8 W ater heater life depends upon water quality , water pressure and the environment in which the water heater is installed. W ater heaters are sometimes installed in locations where leakage may result in property damage, even with the use of a drain pan piped to a drain. However, unanticipated damage can be reduced or prevented by a leak detector ...

  • Kenmore 153.31604 - page 9

    9 W ater Piping HOTTER WA TER CAN SCALD: Water heaters are intended to produce hot water . Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the eld ...

  • Kenmore 153.31604 - page 10

    10 Optional Installation Instructions Some compact models have optional plumbing connections. On these units, if top connection is preferred over the side connection, use the f ollowing instructions as they apply to your connection: T o change T emperature and Pressure (T&P) valve location: Remove 3/4” plug from opening in jacke t top. Replac ...

  • Kenmore 153.31604 - page 11

    1 1 prescribed temperature-pressure relief valve installed in the designated opening in the water heater in place of the factory furnished valve. For safe operation of the water heater , the relief valve must not be removed from its designated opening nor plugged. The temperature-pressure relief valve must be installed directly into the tting of ...

  • Kenmore 153.31604 - page 12

    12 Wiring Y ou must provide all wiring of the proper size outside of the water heater . Y ou must obey local codes and electric company requirements when you install this wiring. If you are not familiar with electric codes and practices, or if you have any doubt, even the slightest doubt, in your ability to connect the wiring to this water heater , ...

  • Kenmore 153.31604 - page 13

    13 TEMPERA TURE SETTINGS It i s re co mm end ed th at th e di al b e se t lo wer w he ne ve r po ss ib le. T emperature Time to Produce 2nd & 3rd Setting Degree Burns on Adult Skin VER Y HOT = approx. 160°F (71°C) About 1/2 second C = approx. 150°F (66°C) About 1-1/2 seconds B = approx. 140°F (60°C) Less than 5 seconds A = approx. 130°F ...

  • Kenmore 153.31604 - page 14

    14 1. T urn “OFF” the electric power to the water heater at the junction box. 2. T ake off the access panel and remove the insulation cap with handle. 3 . Th e sl ot te d ad ju st me nt ( us in g a s cr ew dr iv er ) ca n be t ur ne d clockwise ( ) to increase the temperature setting or counter clockwise ( ) to decrease the temperature setting. ...

  • Kenmore 153.31604 - page 15

    15 Thermostat Removal/Replacement 1. Turn “OFF” the electrical power to the water heater at the junction box. HAZARD OF ELECTRICAL SHOCK! Before removing any access panels or servicing the water heater , make sure the electrical supply to the water heater is turned “OFF”. Failure to do this could result in DEA TH, SERIOUS BODIL Y INJURY OR ...

  • Kenmore 153.31604 - page 16

    16 FIGURE 19. 5. Remove insulation to expose the terminal cover . FIGURE 20. 6. Lif t out the tab as shown to uncl ip the termin al cover from the thermostat. The terminal cover can now be removed from the thermostat. FIGURE 21. 7. Disconnect the two wires on the element and unscrew the old element from the tank. FIGURE 22. 8. Clean the area around ...

  • Kenmore 153.31604 - page 17

    17 FIGURE 24. 16. Replace terminal cover on thermostat making sure that the locking tabs on the terminal cover are in place. FIGURE 25. 1 7 . Replace the insulation to cover the thermostat and the element. FIGURE 26. 18. Replace access panel. 19. T urn “ON” electric power to water heater . FIGURE 27. Drain V alve W asher Replacement. NOTE: For ...

  • Kenmore 153.31604 - page 18

    18 TROUBLESHOOTING Start Up Conditions THERMAL EXP ANSION W ater supply systems may , because of such events as high line pressure, frequent cut-offs, the effects of water hammer among others, have install ed devices such as pressu re reducing valves, chec k valve s, back ow prevente rs, et c...to contro l these types of problems. When these dev ...

  • Kenmore 153.31604 - page 19

    19 Smelly water may be eliminated or reduced in some water heater models by replacing the anode rod(s) with one of less active material, and the chlorinating the water heater tank and all water lines. Contact the local Sears Service Center for further information concerning an Anode Replacement Kit #9001453 and this Chlorination T reatment. Anode r ...

  • Kenmore 153.31604 - page 20

    20 NOT ENOUGH OR NO HOT W A TER 1. In a n ew in sta lla ti on , t he wa te r h ea te r m ay no t b e p ro pe rl y c o n n e c t e d . Ma k e su r e th e co l d wa t e r su pp l y va l ve i s op e n. R e vi e w a nd c he ck pi p in g in st a ll at io n. Ma ke su re t h at t he c ol d wa te r li ne i s c on ne ct ed to t he co ld wa te r in le t to t ...

  • Kenmore 153.31604 - page 21

    21 FIGURE 32. Use th is guid e to ch eck a “Lea king ” wate r he ate r . Ma ny susp ect ed “Leakers” are not leaking tanks. Often the source of the water can be found and corrected. If you are not thoroughly familiar with electric codes, the water heater , and safety practices, contact your local Sears Service Center to check the water heat ...

  • Kenmore 153.31604 - page 22

    22 Now that you have purchased this water heater , should a need ever exist for repair parts or service, simply contact any Sears Service Center or call 1-800-4-MY -HOME (1-800-469-4663). Be sure to provide all pertinent facts when you call or visit. All Parts listed may be ordered from any Sears Service Center and by calling 1-800-366-P ART (1-800 ...

  • Kenmore 153.31604 - page 23

    23 Key Model Numbers No. Part Description 153.316331 153.326331 1 Access Panel 9003900 9003900 2 Anode Rod 9003944 9003944 3 Drain V alve 9000058 9000058 4 Drain V alve W asher (17/32” x 13/64” x 1/8” Thick)** 9001584 9001584 5 Element 9000139 9000133 6 Element Gasket 9000308 9000308 7 Element Insulation Cap 9003723 9003723 8 Inlet W ater Nip ...

  • Kenmore 153.31604 - page 24

    24 6 YEAR LIMITED W ARRANTY ON W A TER HEA TER For six years from the date of purchase, if this water heater is installed and operate d in a single-fami ly home in accorda nce with the owner ’s manual instructions and all local applicable plumbing codes, Sears will supply a free water heater for one that develops a leak. For the second through si ...

Produzent Kenmore Kategorie Water Heater

Dokumente, die wir vom Produzenten des Geräts Kenmore 153.31604 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Kenmore
- Bedienungsanleitungen 153.31604
- Produktkarten Kenmore
- Informationsbroschüren
- oder Energieetiketten Kenmore 153.31604
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Kenmore 153.31604.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Kenmore 153.31604, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Kenmore 153.31604. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Kenmore 153.31604 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Kenmore 153.31604, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Kenmore 153.31604 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Kenmore 153.31604 verständlich ist.

Eine gänzliche Bedienungsanleitung von Kenmore sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Kenmore 153.31604 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Kenmore 153.31604 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Kenmore 153.31604, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Kenmore 153.31604 - die uns die ersten Schritte während der Nutzung von Kenmore 153.31604 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Kenmore 153.31604 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Kenmore 153.31604 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Kenmore 153.31604?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Kenmore 153.31604 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Kenmore 153.31604 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)