Bedienungsanleitung Husqvarna K750

24 Seiten 2.44 mb
Download

Zur Seite of 24

Summary
  • Husqvarna K750 - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h K750 Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna K750 - page 2

    2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Protective he ...

  • Husqvarna K750 - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the po wer cutter? ............................... 4 SAFETY INSTR UCTIONS Steps bef ore using a new ...

  • Husqvarna K750 - page 4

    4 – English WHA T IS WHA T? What is what on the po wer cutter? 13 8 6 7 25 12 11 1 5 24 2 22 10 9 16 15 17 20 21 26 23 14 19 3 4 18 1 F ront handle 2 W ater tap 3 W arning decal 4 Air filter cov er 5 Cylinder cov er 6 Choke 7 Throttle lock out 8 Throttle control 9 Star t throttle lock 10 Stop s witch 11 Star ter handle 12 Star ter 13 Muffler 14 ...

  • Husqvarna K750 - page 5

    English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new po wer cutter . • Please read the operator’ s manual carefully . • Check the cutting b lade’ s mounting, see the chapter ”Assembly”. • Star t the engine and check the idling setting, see instructions under the heading Maintenance. When the carburettor is set correctly the cu ...

  • Husqvarna K750 - page 6

    6 – English SAFETY INSTR UCTIONS Mac hine ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . Vibration dampin ...

  • Husqvarna K750 - page 7

    English – 7 SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′ s safety equipment Vibration damping system Regularly check the vibration damping units f or cracks or def or mation. Make sure the vibr ation damping units are securely attached to the engine unit and handle unit. K eep the handles clean and dry . Stop switc h ...

  • Husqvarna K750 - page 8

    8 – English SAFETY INSTR UCTIONS General safety precautions • A power cutter is designed to cut hard materials, such as masonr y . Obser ve the increased risk of kic kback when cutting soft materials. See instructions under the heading How to a void kic kback. • Do not use the power cutter until y ou have read the entire contents of this Oper ...

  • Husqvarna K750 - page 9

    English – 9 SAFETY INSTR UCTIONS General w orking instructions Basic safety rules • Look around you: - T o ensure that people, animals or other things cannot aff ect your control of the machine . - T o make sure that none of the abo ve come into contact with the cutting blade . • Do not use the machine in bad weather , such as dense f og, rai ...

  • Husqvarna K750 - page 10

    10 – English SAFETY INSTR UCTIONS • Mov e the blade slo wly f orwards and bac kwards to achie v e a small contact area between the b lade and the material to be cut. This reduces the temperature of the b lade and ensures eff ective cutting. • F eed down the machine in line with the b lade. Pressure from the side can damage the blade and is v ...

  • Husqvarna K750 - page 11

    English – 11 SAFETY INSTR UCTIONS Pinching/r otation If the cut is pressed together this can lead to jamming. The machine can be pulled down suddenly with a v ery powerful jerk. How to a v oid pinching Suppor t the work piece in such a wa y that the cut remains open during the cutting operation and when the cut is finished. Cutting blades Genera ...

  • Husqvarna K750 - page 12

    12 – English SAFETY INSTR UCTIONS Ensure the blade it not cr ack ed or damaged in any other w ay . T est the abr asive disc b y hanging it on your finger and tapping it lightly with a screwdriv er or the like . If the disc does not produce a resonant, ringing sound it is damaged. Diamond blades Diamond blades consist of a steel body pro vided wi ...

  • Husqvarna K750 - page 13

    English – 13 ASSEMBL Y Chec king the drive axle and flange washers Check that the threads on the driv e shaft are undamaged. Check that the contact surf aces on the blade and the flange washers are undamaged, of the correct dimension, clean, and that they run properly on the drive axle. Do not use warped, notched, indented or dir ty flange was ...

  • Husqvarna K750 - page 14

    14 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-stroke engine and must alwa ys been r un using a mixture of petrol and two- stroke engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, ev en small inaccuracie ...

  • Husqvarna K750 - page 15

    English – 15 ST AR TING AND ST OPPING Starting and stopping Starting a cold engine Ignition: Slide the ignition s witch to the left. Choke: Pull the choke control fully out. Start throttle lock: Press in the throttle trigger lock, throttle control and then the star t throttle lock (A). Release the throttle control and it is lock ed in the half th ...

  • Husqvarna K750 - page 16

    16 – English MAINTENANCE T ensioning the drive belt • The drive belt is fully enclosed and well protected from dust and dir t. • When the drive belt is to be tensioned, release the bolts holding the cutting arm. • Screw the adjuster scre w so that the square headed nut comes opposite the marking on the cover . This automatically ensures tha ...

  • Husqvarna K750 - page 17

    English – 17 MAINTENANCE Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by b lockage of the fuel filter located inside the tank. • The filter cannot be cleaned but m ust be replaced with a new filter when ...

  • Husqvarna K750 - page 18

    18 – English MAINTENANCE • Pull the cord out about 30 cm and lift it into the cut-out in the peripher y of the star ter pulley . When the cord is intact: Release the spring tension by letting the pulley rotate slowly bac kwards . Remov e any remnants of the old starter cord and check that the return spr ing works. Inser t the new star ter cord ...

  • Husqvarna K750 - page 19

    English – 19 MAINTENANCE Fitting the starter • T o fit the star ter, first pull out the starter cord and place the star ter in position against the crankcase. Then slowly release the star ter cord so that the pulley engages with the pawls . • Tighten the screws . Spark plug The spark plug condition is influenced by: • Wrong fuel mixture ...

  • Husqvarna K750 - page 20

    20 – English MAINTENANCE General maintenance instructions Below y ou will find some general maintenance instructions. If you ha v e more questions, contact your service agent. Daily maintenance 1 Check that the components of the throttle control w ork smoothly (throttle control and throttle tr igger lock). 2 Check the tension of the driv e belt. ...

  • Husqvarna K750 - page 21

    English – 21 TECHNICAL D A T A Note 1: Noise emissions in the environment measured as sound power (L W A ) in conf ormity with EC directive 2000/14/EC . Note 2: Equivalent sound pressure le vel is calculated as the time-w eighted energy total for sound pressure le vels under v arious working conditions with the follo wing time distribution: 1/2 i ...

  • Husqvarna K750 - page 22

    22 – English TECHNICAL D A T A ´®z+R<h¶6(¨ ´®z+R<h¶6(¨ EC-dec laration of conf ormity (Applies to Eur ope only) Husqv arna Construction Pr oducts , SE-433 81 P ar tille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter K750 from year 2006 serial numbers and onward (the y ear is clear ly stated in ...

  • Husqvarna K750 - page 23

    ...

  • Husqvarna K750 - page 24

    ´®z+R<h¶6(¨ 2006-11-23 ´®z+R<h¶6(¨ 1150287-26 ...

Produzent Husqvarna Kategorie Cordless Saw

Dokumente, die wir vom Produzenten des Geräts Husqvarna K750 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen K750
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna K750
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna K750.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna K750, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna K750. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna K750 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna K750, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna K750 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna K750 verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna K750 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna K750 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna K750, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna K750 - die uns die ersten Schritte während der Nutzung von Husqvarna K750 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna K750 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna K750 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna K750?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna K750 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna K750 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)