Bedienungsanleitung Jonsered GT2125L

28 Seiten 1.07 mb
Download

Zur Seite of 28

Summary
  • Jonsered GT2125L - page 1

    Operator´s manual (EP A) Please read these instructions carefully and make sure you understand them before using the machine. ...

  • Jonsered GT2125L - page 2

    2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. Always use • A protective helmet where ther ...

  • Jonsered GT2125L - page 3

    English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The ...

  • Jonsered GT2125L - page 4

    4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) P ersonal pr otective equipment SAFETY INS ...

  • Jonsered GT2125L - page 5

    English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration. The machine ’ s vibration damping system reduces the ...

  • Jonsered GT2125L - page 6

    6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . SAFETY INSTR UCTIONS Contr ol, maintenance and service of the machine ‘ ...

  • Jonsered GT2125L - page 7

    English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment. T wo basic rules: 1) Only use the cutting and guard equipment we recommend! See ch ...

  • Jonsered GT2125L - page 8

    8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and tra ...

  • Jonsered GT2125L - page 9

    English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the engine (that is without resistance, which the engine feels from the cutting equipment when trimming) can lead to serious engine damage. ...

  • Jonsered GT2125L - page 10

    10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord. • The cord wears quicker and must be fed forward ...

  • Jonsered GT2125L - page 11

    English – 11 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. C ylinder cover 11. S tarter handle 12. F uel tank 13. Choke 14. Air purge 15. Air filter cover 16. Clutch cov er 17. Handlebar adjustment ...

  • Jonsered GT2125L - page 12

    12 – English ASSEMBL Y Assembling the loop handlebar (GT2125L) Assembl y of the trimmer head I t is extremely important that the disc drive ’ s/support flange ’ s guide engages correctly in the cutting equipment ’ s centre hole when assembling the cutting equipment. C utting equipment assembled incorrectly can r esult in serious and/or fata ...

  • Jonsered GT2125L - page 13

    English – 13 ASSEMBL Y • Fit the guard (A) intended for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive ’ s holes aligns with the corresponding hole in the gear housing. • Insert the locking pi ...

  • Jonsered GT2125L - page 14

    14 – English FUEL HANDLING Fuel mixture NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of petrol and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensur e the correct mixtur e ratio. Small discr epancies in the amount of oil have a great bearing on the pr oportions of th ...

  • Jonsered GT2125L - page 15

    English – 15 ST AR T AND ST OP Contr ol before starting F or reasons of safety follo w these recommendations! • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force. The nut lock should have a locking ...

  • Jonsered GT2125L - page 16

    16 – English Basic setting • The carburettor is set to its basic setting when test run at the factory. The basic setting is richer than the optimal setting and should be kept during the machine ‘ s first working hours. Thereafter the carburettor should be finely adjusted. Fine adjustment should be carried out by a skilled technician. NO TE! I ...

  • Jonsered GT2125L - page 17

    English – 17 MAINTENANCE H needle. The high speed needle is adjusted corr ectly when the machine ‘ splatters ’ a little . If the machine smokes heavily at the same time as it ‘ splatters ’ heavily the adjustment is too rich. The high speed needle affects the machine ’ s power , speed, temperature and fuel consumption. A too lean adjustm ...

  • Jonsered GT2125L - page 18

    18 – Française ENTRETIEN Circuit de refroidissement P our obtenir une température de service aussi basse que possible, le moteur est muni d’un circuit de refroidissement. Le système de refroidissement se compose de: 1. Prise d’air au niveau du démarreur. 2. Ailettes de ventilation sur la roue volante. 3. Ailettes de refroidissement sur le ...

  • Jonsered GT2125L - page 19

    English – 19 MAINTENANCE The angle gear is filled with a sufficient quantity of grease at the factory . However , before using the machine you should check that the angle gear is filled to 3/4 with grease. U se JONSERED special grease. N ormally , the grease does not need to be changed except when repairs ar e carried out. Air filter The air filt ...

  • Jonsered GT2125L - page 20

    20 – English TECHNICAL D A T A T echnical data Engine Displacement, cu. in/cm 3 Cylinder bor e, inch/mm S troke length, inch/mm Recommended max. speed, rpm I dling speed, rpm S peed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/rpm Catalytic converter muffler S peed-regulated ignition system Ignition system Manufactur er/type of i ...

  • Jonsered GT2125L - page 21

    English – 21 EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (U.S. Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. In U.S. and Canada, new small off-road engines must be designed, bui ...

  • Jonsered GT2125L - page 22

    22 – English 1 Poly T rim 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10 ...

  • Jonsered GT2125L - page 23

    English – 23 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...

  • Jonsered GT2125L - page 24

    24 – English 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6" ...

  • Jonsered GT2125L - page 25

    English – 25 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 12 3 4 56 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 1 1" T rimmy VII ...

  • Jonsered GT2125L - page 26

    26 – English 1 T ap-N-Go Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6" ´*xty¶5s¨ ...

  • Jonsered GT2125L - page 27

    ...

  • Jonsered GT2125L - page 28

    2002W11 ´*xty¶5s¨ 108 88 48-95 ...

Produzent Jonsered Kategorie Brush Cutter

Dokumente, die wir vom Produzenten des Geräts Jonsered GT2125L erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Jonsered
- Bedienungsanleitungen GT2125L
- Produktkarten Jonsered
- Informationsbroschüren
- oder Energieetiketten Jonsered GT2125L
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Jonsered GT2125L.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Jonsered GT2125L, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Jonsered GT2125L. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Jonsered GT2125L ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Jonsered GT2125L, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Jonsered GT2125L hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Jonsered GT2125L verständlich ist.

Eine gänzliche Bedienungsanleitung von Jonsered sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Jonsered GT2125L bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Jonsered GT2125L befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Jonsered GT2125L, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Jonsered GT2125L - die uns die ersten Schritte während der Nutzung von Jonsered GT2125L erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Jonsered GT2125L hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Jonsered GT2125L im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Jonsered GT2125L?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Jonsered GT2125L nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Jonsered GT2125L hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)