Bedienungsanleitung CFM Corporation SHR48

24 Seiten 1.66 mb
Download

Zur Seite of 24

Summary
  • CFM Corporation SHR48 - page 1

    1384 SHR cov er 5/27/99 djt SHR Series W oodburning Fireplace For Models: SHR36 SHR42A SHR48 SHR52 Underwriter's Laboratories Report No. MH6018 DO NOT DISCARD THIS MANUAL: Retain for future use. 20001384 4/07 Rev . 19 Homeowner's Installation and Operating Manual ...

  • CFM Corporation SHR48 - page 2

    2 SHR Series W oodbur ning Fireplace 20001384 Safety Information PLEASE READ THIS MANUAL BEFORE INST ALLING AND USING FIREPLACE. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty . Description The SHR Series ? ...

  • CFM Corporation SHR48 - page 3

    3 SH R Series W oodb urning Fireplaces 20001384 Rough Opening Height 42" (1067mm) 52  " (1327mm) 48  " (1222mm)  "  " 28  " (724mm)  " (189mm) 13  " Dia. (340mm) Rough Opening Width 53  " Rough Opening Depth 65  " ...

  • CFM Corporation SHR48 - page 4

    4 SHR Series W oodbur ning Fireplace 20001384  " (724mm) 7  " (197mm ) 48" (1219mm) 58  " (1480mm) 48  " (1232mm)  "  "  " (189mm) 13  " Dia. (340mm) Rough Opening Width 59  " Rough Opening Height Rough Open ...

  • CFM Corporation SHR48 - page 5

    5 SH R Series W oodb urning Fireplaces 20001384 FP554A SH Series  1/28/99 djt Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation. FP554A Fig. 5 Fireplace and chase parts identification. (SHR48 shown) T ermination Cap Storm Collar Pan Flashing Batt Insulation (cut out around firest ...

  • CFM Corporation SHR48 - page 6

    6 SHR Series W oodbur ning Fireplace 20001384 Chimney Requirements - Offset Installations 0 0 0 0 0 3" 1 1" 1 0 0 0 0 8 ¹⁄₄ " 20" 0 1 0 0 0 1 1 ¹⁄₄ " 25 ¹⁄₄ " 2 0 0 0 0 13 ¹⁄₂ " 29 ¹⁄₄ " 1 1 0 0 0 16 ¹⁄₂ " 34 ¹⁄₄ " 0 0 1 0 0 20 ¹⁄₄ " 40 ³⁄₄ " 2 ...

  • CFM Corporation SHR48 - page 7

    7 SH R Series W oodb urning Fireplaces 20001384 Planning Information The T en Foot Rule Major U.S. building codes specify a minimum chimney height above the roof top. The “T en Foot Rule” is a fire safety rule and not a draft rule. T o ensure proper draft, it is recommended that you always meet or exceed the “T en Foot Rule,” especially wh ...

  • CFM Corporation SHR48 - page 8

    8 SHR Series W oodbur ning Fireplace 20001384 Installation Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30 feet above the hearth. Chimney supports are required if the vertical height exceeds 30 feet with 1 1CF chimneys. Locate chimney supports at ceiling holes or other structural framing ...

  • CFM Corporation SHR48 - page 9

    9 SH R Series W oodb urning Fireplaces 20001384 Framing Framing can be constructed before or after the fireplace is set in place, however , most installers build the frame before setting the fireplace. Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figures 1 - 4 for basic fireplace specifications. NOTE: ...

  • CFM Corporation SHR48 - page 10

    10 SHR Series W oodbur ning Fireplace 20001384 FP556SHR Fig. 13 Locate centerline of chimney with plumb line. FP556SHR SHR LOCA TE CENTER LINE 5/11/99 djt Chimney Centerline Actual Centerpoint Plumb Line Plumb Bob Imaginary Centerpoint 1 1 ¹⁄₈ " (283 mm) FP 548b SHR 5/1 1/99 djt Angle of Chimney at Ceiling Size of Chimney V ertic ...

  • CFM Corporation SHR48 - page 11

    1 1 SH R Series W oodb urning Fireplaces 20001384 The inside dimension of the frame must be the same as the hole size selected from Figure 1 1 in order to provide the required 2 inches of air space between the outside diameter of the chimney and the edges of the framed ceiling hole. Positioning, Safety Strips, Securing the Fireplace Slide fireplac ...

  • CFM Corporation SHR48 - page 12

    12 SHR Series W oodbur ning Fireplace 20001384 Installing the Chimney System Start by attaching the first chimney section to the collar on top of the fireplace. Install the pipe as pictured in Figure 19. When you get a good lock, you will hear the pipe clearly snap together . Once sections are snap-locked in place, it is extremely difficult to g ...

  • CFM Corporation SHR48 - page 13

    13 SH R Series W oodb urning Fireplaces 20001384 Attic Installation Ceiling Installation Fig. 21 Installing firestop spacer . FP285 IWF285 mbuf 5/25/96   Nails (4) Firestop Spacer Joist Joist Firestop Spacer Nails (4) Flange Down Into Hole Flange Up Into Hole NOTE: If the attic insulation shield is used, the firestop is not required i ...

  • CFM Corporation SHR48 - page 14

    14 SHR Series W oodbur ning Fireplace 20001384 Cut and Frame Roof Hole Size of roof hole varies with the type of chimney termi- nation installed. Refer to installation instructions pro- vided with the chimney termination to find correct size roof hole. There must be a 2" (51 mm) air space between out- ermost portion of chimney sections and an ...

  • CFM Corporation SHR48 - page 15

    15 SH R Series W oodb urning Fireplaces 20001384 FP1166 surround flush with finished wall 12/20/01 djt Stud 2 x 4 Header Ledge Bracket Surround Must be Sealed with Noncombustible Material Noncombus- tible Decorative Facing Finished W all FP1 166 Fig. 26 Fireplace surround flush with finished wall. FP1277 SHR52 drywall finish 1/30/03 djt Finish ...

  • CFM Corporation SHR48 - page 16

    16 SHR Series W oodbur ning Fireplace 20001384 FP1167 facing flush with finished wall 12/20/01 djt Finished W all Stud Noncombustible Decorative Fac- ing Must be Sealed with Noncombustible Material Surround 2 x 4 Finished Header Covered W all Ledge Bracket FP1 167 Fig. 27 Facing on fireplace surround flush with finished wall. FP1168 finishing fr ...

  • CFM Corporation SHR48 - page 17

    17 SH R Series W oodb urning Fireplaces 20001384 Side W all Protection Adjacent combustible side walls that are within dimen- sions shown in Figure 30 of fireplace opening must be protected with W all Shield Model SP40 or a specifically built wall shield described in Figure 29. The special wall shield design described in Figure 27 is an alternate ...

  • CFM Corporation SHR48 - page 18

    18 SHR Series W oodbur ning Fireplace 20001384 FP532SHR Fig. 32 Combustible side wall protection and hearth extension dimensions. Minimum W all Clearances WITH Noncombustible Surround Facing WITHOUT Noncombustible Surround Facing Minimum Hearth Extension Dimensions (for On-Site Construction) G H G J Seal cracks between the fireplace and hearth exte ...

  • CFM Corporation SHR48 - page 19

    19 SH R Series W oodb urning Fireplaces 20001384 removed from gas line tube to repack space around the pipe. Material should be inserted from outside of the fireplace and packed tightly to totally seal between the pipe and tube. NOTE: Gas pipe should not come in contact with any wood structures until it has reached a point at least one (1) inch aw ...

  • CFM Corporation SHR48 - page 20

    20 SHR Series W oodbur ning Fireplace 20001384 1384 pts replacement parts 5/27/99 djt 7/14/99 removed clips,added push nut 1 2 3 4 5 6 7 8 a b c 9 10 1 1 d 12 13 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. SHR36/42A/48/52 W oodburni ...

  • CFM Corporation SHR48 - page 21

    21 SH R Series W oodb urning Fireplaces 20001384 Description Designed to enclose the fireplace opening with glass doors allowing the fire to remain visible. Available in Polished, Brushed Brass, Black and Pewter Provides outside air for fuel conbustion in the firebox. This accessory must be installed before fireplace is installed. Located on th ...

  • CFM Corporation SHR48 - page 22

    22 SHR Series W oodbur ning Fireplace 20001384 Accessory Description Model No. Contemporary Flashing Contemporary Chase T op T ermina- tion Contemporary Round T op T ermina - tion Extended Round T op Chimney Sections Chimney Elbows T op Housing with Upper Baffle Attic Insulation Shield Required for contemporary top termination on the roof to preve ...

  • CFM Corporation SHR48 - page 23

    23 SH R Series W oodb urning Fireplaces 20001384 LIMITED W ARRANTY & 30 YEAR PROTECTION PLAN For MAJESTIC FIREPLACES ® PRE-ENGINEERED Fireplace Systems CFM Corporation warrants its MAJESTIC FIREPLACES® Pre- Engineered Fireplace (“Fireplace”) and the CFM Corporation supplied firegrate, glass doors, outside air system, fan motor , and line ...

  • CFM Corporation SHR48 - page 24

    © CFM Corporation 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Produzent CFM Corporation Kategorie Outdoor Fireplace

Dokumente, die wir vom Produzenten des Geräts CFM Corporation SHR48 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen CFM Corporation
- Bedienungsanleitungen SHR48
- Produktkarten CFM Corporation
- Informationsbroschüren
- oder Energieetiketten CFM Corporation SHR48
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung CFM Corporation SHR48.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen CFM Corporation SHR48, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen CFM Corporation SHR48. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts CFM Corporation SHR48 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts CFM Corporation SHR48, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von CFM Corporation SHR48 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von CFM Corporation SHR48 verständlich ist.

Eine gänzliche Bedienungsanleitung von CFM Corporation sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von CFM Corporation SHR48 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von CFM Corporation SHR48 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich CFM Corporation SHR48, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts CFM Corporation SHR48 - die uns die ersten Schritte während der Nutzung von CFM Corporation SHR48 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit CFM Corporation SHR48 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von CFM Corporation SHR48 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich CFM Corporation SHR48?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit CFM Corporation SHR48 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit CFM Corporation SHR48 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)