Bedienungsanleitung Country Home Products TLC18-CHP

36 Seiten 2.54 mb
Download

Zur Seite of 36

Summary
  • Country Home Products TLC18-CHP - page 1

    DR CHIPPER Operating & Assembly Instruction Manual Model: 18.0 HP TLC18-CHP This manual contains informati on concerning pr oper and improper operating procedures, warnings, maintenance, troubleshooting, assembly, and tips. Everyone who operates this machine should read these instructions and be thoroughly familiar with them. P/N 913-0268 12/31 ...

  • Country Home Products TLC18-CHP - page 2

    SECTION I - SAFETY This symbol points out impor tant safety instructions , which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper. Failure to comply with these instructions may result in personal injury. When you see ...

  • Country Home Products TLC18-CHP - page 3

    WARNING California to cause cancer, birth def : The Engine Exhaust from this product contai ns chemicals known to the state of ects or other reproductive harm. MAKE CERTAIN THAT ALL SAFETY LABELS ON THIS EQUIPMENT ARE KEPT CLEAN AND IN GOOD CONDITION. IF YOU NEED REPLACEMENT LABELS, ORDER BY PART NUMBER. 080-0967 080-0970 091-0055 3 ...

  • Country Home Products TLC18-CHP - page 4

    091-0057 091-0059 091-0062 091-0088 091-0093 4 ...

  • Country Home Products TLC18-CHP - page 5

    091-0256 091-0378 091-0379 091-0380 091-0381 5 ...

  • Country Home Products TLC18-CHP - page 6

    091-0384 913-0265 6 ...

  • Country Home Products TLC18-CHP - page 7

    SAFE OPERATION PRACTICES TRAINING • Read this owner’s manual carefully in its entirety bef ore attempting to assemble this machine. Read, understand, and follow all instructions on the machine bef ore operation. Be completely familiar with the controls and the proper use of the machine before operating it. Keep this manual in a safe place for f ...

  • Country Home Products TLC18-CHP - page 8

    OPERATION • Never place your hands, feet, or any part of your body in the chipper chute, discharge opening, or near or under any moving part while the engine is running. Keep clear of the discharge opening at all times. If it becomes necessary to push material into the chipper chute, use a small diameter stick, NOT YOUR HANDS. • Keep your face ...

  • Country Home Products TLC18-CHP - page 9

    • Do not allow an accumulation of processed material to build up in the discharge area as this will prevent proper discharge and can result in kick-back from the chipper chute. • Do not allow any part of the engine, especially around the cooling fans and muffler, to become clogged with processed material, leaves, oil, greas e or any other combu ...

  • Country Home Products TLC18-CHP - page 10

    • Only operate your chipper from the operator zone. • Know how to turn your unit off. • Never move your chipper or leave it unattended with the engine running. • Do not operate your chipper on concrete or blacktop. • Follow engine owner’s manual for engine maintenance and repair. YOUR RESPONSIBILITY • Restrict the use of this power ma ...

  • Country Home Products TLC18-CHP - page 11

    SECTION II - ASSEMBLY INSTRUCTIONS PACKAGE CONTENTS SKID PARTS BO X BOLT BA G CHIPPER CHIPPER HOPPER 7 EA – 5/16-18 X ¾” CARRIAGE BOLTS DISCHARGE CHUTE SWIVEL TOP 8 EA – 5/16-18 NYLOCK NUT HITCH ARMS DEFLECTOR 4 EA – 5/16 USS FLATWASHER HITCH ASSEMBLY STAND ASSEMBLY 2 EA – ½-13 X 3” HHCS PARTS BOX WIRE HARNESS 4 EA – ½-13 X 1 ¼” ...

  • Country Home Products TLC18-CHP - page 12

    STEP III – ATTACHING THE HITCH ARMS AND TRAILER HITCH ASSEMBLY 1. Attach the hitch arms (item #39, pg. 29) to the traile r frame using the two hitch arm mounting plates (item #52, pg. 29) and four 1/2”-13 x 1-1/4” HHCS (ite m #38, pg. 29) from the bolt bag. Do not tighten hardware at this time. 2. Attach the trailer hitch assembly (item #45 & ...

  • Country Home Products TLC18-CHP - page 13

    STEP V – ATTACHING THE SWIVEL TOP AND DEFLECTOR 1. Get three 5/16-18 X ¾” carriage bolts (item #2, pg. 29) , two 5/16-18 nylock nuts (item #5, pg. 29), three 3/8” flat-washers(item #60, pg. 30), and the locki ng knob (item #12, pg 29) from the bolt bag. 2. Hold the Swivel Top (item #10, pg. 29) in place and insert two of the 5/16-18 x ¾” ...

  • Country Home Products TLC18-CHP - page 14

    STEP VI – ATTACHING THE WIRE HARNESS Identify the “road side” and “curb side” of your trailer per the picture below. The mounting brackets have an access hole in them so the wire harness can be attached to the light. On the wire harness the yellow/brown wire is for the road side light and the green/brown wire is for the cu rb side light. ...

  • Country Home Products TLC18-CHP - page 15

    SECTION III - OPERATION BEFORE STARTING ENGINE, ALWAYS CHECK OIL LEVEL! Refer to the engine owner’s manual for further details regarding OPERATION AND MAINTENANCE OF the engine. NOTE: ENGINE IS SHIPPED WITHOUT OIL! FILL CRANKCASE WITH OIL BEFORE STARTING ENGINE. BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR ...

  • Country Home Products TLC18-CHP - page 16

    CHECKING AND ADDING OIL • Check oil level before starting the engine. • Check level daily, or after every eight hours. • Keep oil level at FULL. • Do not overfill. Oil filling procedure: first add 1 quart. Start and run engine at idle for 30 seconds. Shut engine off and wait 30 seconds. Then add more oil slowly to bring level to Full mark o ...

  • Country Home Products TLC18-CHP - page 17

    STARTING AND STOPPING STARTING AND OPERATING TIPS • Store and fuel equipment in level position. • Use fresh fuel. • Use correct type of oil. • Remove external equipment/engine loads. • Periodically remove any debris buildup from the machine. • After engine has started, let it warm up seve ral seconds to several minutes, depending on out ...

  • Country Home Products TLC18-CHP - page 18

    SECTION IV - CHIPPING THIS CHIPPER WAS DESIGNED FOR CHIPPING LIMBS OR BRANCHES. NEVER USE THIS MACHINE FOR ANY OTHER PURPOSE AS IT COULD CAUSE SERIOUS INJURY. SAFETY FIRST • Always wear protective gloves and safety glasses during operation of the chipper. • Never allow your hands or any part of your body or clothing inside the chipper hopper or ...

  • Country Home Products TLC18-CHP - page 19

    • USE COMMON SENSE WHEN USING YOUR CHIPPER. • LEARN TO RECOGNIZE THE CHANGE IN THE SOUND OF YOUR MACHINE WHEN IT IS OVERLOADED. • BECOME FAMILIAR WITH SUCCESSFUL OPERATING CONDITIONS AND AVOID THOSE THAT CAN OVER LOAD AND DAMAGE THE MACHINE. • IF THE MACHINE BECOMES JAMMED BY OVERLOADING OR ANY OTHER CAUSE, STOP THE MACHINE IMMEDIATELY. • ...

  • Country Home Products TLC18-CHP - page 20

    TO FREE A JAMMED FLYWHEEL • Stop the engine. • Remove both spark plug wires and keep away from spark plugs. • Disconnect battery at negative terminal. • Remove any material left in the chipper hopper. • Remove discharge chute weldment. NOTE: Never pry against the scroll weldment when removing the discharge chute or at any other time. This ...

  • Country Home Products TLC18-CHP - page 21

    SECTION V - MAINTENANCE AND STORAGE IMPORTANT: The knife should be checked for sharpness and the nuts and bolts attaching it to the flywheel for tightness every 8-10 hours of operation. IMPORTANT: Every time you perform maintenance or any kind of service or check on the knife, be sure to check the gap betw een the knife and w ear plate for proper s ...

  • Country Home Products TLC18-CHP - page 22

    REMOVAL, SHARPENING AND RE-INSTALLATION OF CHIPPER KNIFE HOW TO REMOVE THE KNIFE • Stop the engine. • Remove both spark plug wires and keep away from spark plugs. • Disconnect battery at negative terminal. • Remove both access covers from the chipper basic machine. • Rotate the chipper disk until the three count ersunk screws and nylock n ...

  • Country Home Products TLC18-CHP - page 23

    • The knife should never be sharpened to the extent that more than 3/32” is taken off this measurement. • Once this measurement is below 7/32” (s ee figure 3) the knife should be replaced. • If you are unable to remove dents or gouges wit h these guidelines, replace the knife. Figure 3 KNIFE INSTALLATION • Clean chipper disk where knife ...

  • Country Home Products TLC18-CHP - page 24

    AFTER ANY BLADE OR WEAR PLATE MAINTENANCE OR ADJUSTMENT, ROTATE THE CHIPPER DISK BY HAND. WATCH AND LISTEN CAREFULLY FOR ANY UNUSUAL NOISES, CLICKING OR VIBRATION. IF ANY OF THESE ARE DETECTED, INSPECT THE MACHINE FOR DAMAGE, REPAIR OR REPLACE ANY DAMAGED PARTS AND CHECK FOR ANY LOOSE PARTS AND RETIGHTEN. KNIVES MUST BE CHECKED AND MAINTAINED! KNIV ...

  • Country Home Products TLC18-CHP - page 25

    INSTRUCTIONS FOR ADJUSTING OR REPLACING BELT BELT ADJUSTMENT The belt on your chipper should deflect 3/8” under three pounds of pressure as shown in figure 1 below. If it doesn’t, adjust per the following directions. Figure 1 • Remove belt guard. • Loosen engine bolts. • Tighten or loosen the nut on the belt tensioner until you have the c ...

  • Country Home Products TLC18-CHP - page 26

    TROUBLESHOOTING SYMPTOM PROBLEM CORRECTION Clutch overheats. Belt burns. Flywheel won’t turn. Clutch is slipping or flywheel is jammed or stopped. • Immediately stop engine. • Remove spark plug wires. • Turn flywheel by hand to be sure it turns freely. • Check belt tension. • Clear chipper chamber. Chipping action seems too slow or flyw ...

  • Country Home Products TLC18-CHP - page 27

    LUBRICATION AND MAINTENANCE OPERATION TIME PROCEDURE COMMENTS BREAK IN • Change engine oil and filter after first five hours. • Check belt tension. • Check all nuts and bolts for tightness. • Follow oil recommendations per the engine & owner’s manual. • Adjust per directions. • Tighten if necessary. 8 HOURS • Check engine oil. ? ...

  • Country Home Products TLC18-CHP - page 28

    CENTRIFUGAL CLUTCH INSTALLATION AND SERVICING INSTRUCTIONS FOR CLUTCH 911-0236 REMOVAL 1. Remove clutch from shaft by removing bolt and washers. 2. Slide clutch off shaft. 3. Remove key from keyway. INSTALLATION 1. Clean the shaft and remove any burrs. 2. Install spacer onto shaft. 3. Apply anti-seize compound to shaft. 4. Place key in keyway in sh ...

  • Country Home Products TLC18-CHP - page 29

    SECTION VI – PARTS LIST & ASSEMBLY DRAWINGS TLC18-CHP PARTS LIST ITEM # PART # QTY DESCRIPTION 1 030-0325 1 18HP B&S VANGUARD ENGINE 2 090-0462 10 5/16-18 X 3/4" CARRIAGE BOLT 3 913-0375 1 CHIPPER HOPPER 4 090-0233 25 5/16 USS FLATWASHER 5 090-0460 37 5/16-18 NYLOCK NUT 6 913-0232 1 CHIPPER BASIC MACHINE 7 913-0284 1 DISCHARGE CHUTE ...

  • Country Home Products TLC18-CHP - page 30

    TLC18-CHP PARTS LIST ITEM # PART # QTY DESCRIPTION 43 090-0234 3 3/8 USS FLATWASHER 44 408-0078 2 SAFETY CHAIN 45 911-0220 1 HITCH TUBE WELDMENT 46 913-0218 1 TRAILER HITCH 47 090-0370 4 1/2-13 X 3" HHCS 48 090-0123 1 3/8-16 X 3 1/2" HHCS 49 913-0223 1 NEGATIVE BATTERY CABLE 50 500-0039 1 3/16" COTTER PIN 51 911-0035 1 STAND 52 911-0 ...

  • Country Home Products TLC18-CHP - page 31

    31 ...

  • Country Home Products TLC18-CHP - page 32

    32 ...

  • Country Home Products TLC18-CHP - page 33

    913-0232 CHIPPER BASIC MACHINE ITEM # PART # QTY DESCRIPTION 1 090-0048 9 5/16-18 GRIPCO LOCKNUT 2 030-0115 2 BEARING 3 090-0233 8 5/16 USS FLATWASHER 4 090-0049 4 3/8-16 GRIPCO LOCKNUT 5 030-0117 1 RETAINING RING 6 090-0024-3 2 SHIM 7 090-0162 8 10-32 X 3/8” SCREW 8 913-0210 2 ACCESS COVER 9 913-0034 1 DRIVE SIDE PLATE WELDMENT 10 090-0460 7 5/1 ...

  • Country Home Products TLC18-CHP - page 34

    34 ...

  • Country Home Products TLC18-CHP - page 35

    NOTES 35 ...

  • Country Home Products TLC18-CHP - page 36

    NOTES COUNTRY HOME PRODUCTS Meigs Road, P.O. Box 25, Vergennes, Vermont 05491 1(800) DR-OWNER (376-9637) 12/31/03 36 ...

Produzent Country Home Products Kategorie Chipper

Dokumente, die wir vom Produzenten des Geräts Country Home Products TLC18-CHP erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Country Home Products
- Bedienungsanleitungen TLC18-CHP
- Produktkarten Country Home Products
- Informationsbroschüren
- oder Energieetiketten Country Home Products TLC18-CHP
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Country Home Products TLC18-CHP.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Country Home Products TLC18-CHP, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Country Home Products TLC18-CHP. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Country Home Products TLC18-CHP ansehen.

Die komplette Bedienungsanleitung des Geräts Country Home Products TLC18-CHP, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Country Home Products TLC18-CHP hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Country Home Products TLC18-CHP verständlich ist.

Eine gänzliche Bedienungsanleitung von Country Home Products sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Country Home Products TLC18-CHP bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Country Home Products TLC18-CHP befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Country Home Products TLC18-CHP, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Country Home Products TLC18-CHP - die uns die ersten Schritte während der Nutzung von Country Home Products TLC18-CHP erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Country Home Products TLC18-CHP hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Country Home Products TLC18-CHP im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Country Home Products TLC18-CHP?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Country Home Products TLC18-CHP nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Country Home Products TLC18-CHP hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)