Bedienungsanleitung Remington 476

20 Seiten 0.7 mb
Download

Zur Seite of 20

Summary
  • Remington 476 - page 1

    REMINGT ON ® POWERHAMMER Model 476 Operating Instructions The Remington Powerhammer is de- signed for use with Remington Powder 22 caliber, Type A crimped loads and Remington Power Fasteners which are no longer than 63.5mm (2 1/2”). Remington Power Fasteners are manu- factured from special steel and heat treated to produce a very hard, yet duc- ...

  • Remington 476 - page 2

    2 W ARNING: Safety Precautions BEFORE USING 1. ALWAYS handle the tool as if it were loaded. Before starting work, check that the tool is unloaded and the muzzle is clear. NEVER load a tool unless it is going to be used. 2. ALWAYS inspect to make sure the tool is working properly. If the tool does not work properly or is dam- aged remove from servic ...

  • Remington 476 - page 3

    3 Safety Precautions DEFECTIVE WARNING POWDER ACTUATED TOOLS IN USE! G 018 G 018 ...

  • Remington 476 - page 4

    4 Safety Precautions HANDLING THE TOOL 1. NEVER place your hand over the muzzle. Accidental discharge can cause serious injury. 2. ALWAYS store UNLOADED pow- der actuated tool and loads in a locked container. Keep powder loads of different power levels in separate containers. 3. NEVER carry or pass a loaded pow- der actuated tool. NEVER point a pow ...

  • Remington 476 - page 5

    5 Safety Precautions PO W D ER LO A DS PO W D LO AD G 018 G 018 G 018 G 018 G 018 ...

  • Remington 476 - page 6

    6 3 . NEVER make fastenings in spalled or cracked areas. Safety Precautions KNOW YOUR FASTENING BASE MATERIAL 1. ALWAYS know the thickness and type of base material into which you are fastening. NEVER GUESS . Test the base material by using the Center Punch Test. The Center Punch Test is performed by using a hammer to test drive the particular fast ...

  • Remington 476 - page 7

    7 Safety Precautions ? ? ? ? CENTER PUNCH TEST Sinks in with average hammer blow TOO SOFT TOO HARD Point flattens Surface shatters Start 3 GREEN 2 BROWN 4 YELLOW CAST IRON GLASS TILE BRICK 1 GRAY TOO BRITTLE G 018 G 018 G 018 G 018 G 018 G 018 ...

  • Remington 476 - page 8

    8 Safety Precautions 4. NEVER drive fasteners into thin or easily penetrated materials unless it is backed by concrete or steel. When in doubt, such as when base material is concealed, conduct a Center Punch Test. Check continu- ally to avoid fastening into unsuit- able material, especially in older buildings. 5. DO NOT fasten thru or within 13mm ( ...

  • Remington 476 - page 9

    9 Safety Precautions 1” TOO THIN WELD 1/2” NO YES G 018 G 018 G 018 G 018 76 mm 3" 3X 1X 76mm 3" 76mm 3" 76mm 3" 5 mm MIN 3/16" 25 mm 1" 13 mm 1/2" ...

  • Remington 476 - page 10

    10 OPERATING THE TOOL 1. ALWAYS hold tool perpendicular to work surface. 2. Should the tool fail to fire, hold the muzzle firmly against the work sur- face for 30 seconds. Then remove the tool, eject the load and safely discard the misfired load into water or oil. 3. ALWAYS use the spall shield when driving directly into concrete or steel. ALWAYS w ...

  • Remington 476 - page 11

    11 GAS LINE GASOLINE 482-49 POWDER LOADS 482-51 PO W DER LO ADS Safety Precautions 90 ° 30 WATER Spall Shield G 018 G 018 G 018 G 018 G 018 ...

  • Remington 476 - page 12

    12 6. Fasteners are a permanently in- stalled fixture. An act of demolition is required for their removal. Appro- priate safety precautions must be taken. Safety Precautions 2. Remington Powder Loads are available in four power levels with gray (1) being the lowest power level and yellow (4) being the high- est power level. Always start with the lo ...

  • Remington 476 - page 13

    13 PO W D ER LO A DS 482-54 POWDER LOADS 482-55 YELLOW? BROWN ? GREEN ? GRAY ? NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool. Safety Precautions Start 3 GREEN 2 BROWN 4 YELLOW 1 2 3 4 5 6 7 8 9 10 11 12 1 22 L E K C I N B R A S S 482-53 C A L I B E R 1 GRAY POWER LOADS ONLY! G ...

  • Remington 476 - page 14

    14 Safety Precautions 7. NEVER use fasteners longer than 63.5mm (2 1/2”). NEVER use com- mon nails. Remington Power Fas- teners are manufactured from spe- cial steel and heat treated to pro- duce a very hard, yet ductile fas- tener. 8. NEVER pry a load out of the cham- ber. Prying can discharge the load causing serious injury. 9. ALWAYS insert th ...

  • Remington 476 - page 15

    15 Safety Precautions Overdriven Fasteners An overdriven fastener results when too strong of a powder load is used causing the piston to extend past the muzzle. Move to the next lightest powder load. Repeated overdrive will damage your tool. By avoiding overdrive, you can ex- tend the life of your tool considerably. NOTE: NEVER fire the tool withou ...

  • Remington 476 - page 16

    16 LOADING THE POWERHAMMER 1. Insert the proper fastener into the muzzle, round metal head first. Push fastener until the point is even with the end of the muzzle. 2. Grab the muzzle and pull forward until it stops. This sets the piston and opens the chamber area. 3. Insert the proper Remington Pow- der Load into the chamber, while holding the muzz ...

  • Remington 476 - page 17

    17 Operation Spring Must Be Compressed Firing Pin Line Up Grooves Muzzle Firing Pin Grip Barrel Chamber LOADING FIRING EJECTING Continued ...

  • Remington 476 - page 18

    18 CARE OF YOUR POWERHAMMER Clean your Powerhammer after each day’s use. Clean chamber with acces- sory wire brush, part number 56485. Apply good quality penetrating lubricant spray (such as WD-40) sparingly and wipe dry. NOTE: The labor regulations of many counties require that the operator of this tool on a job site be thoroughly trained and ce ...

  • Remington 476 - page 19

    19 Limited W arranty DESA International warrants this Remington Model 476 POWERHAMMER against defects in materials and workmanship for a period of 30 days from the date of purchase. This warranty extends only to the original purchaser of the POWERHAMMER and only applies if the POWERHAMMER is used for normal household (non-commercial or non-professi ...

  • Remington 476 - page 20

    101915-01 Rev. B 8/96 IMPORTANT This tool is designed to use Remington 22 caliber neck-down crimped loads, power levels 1 (gray) through 4 (yellow). Straight Wadded Power Load Neck-Down Crimped Power Load NOTICE: This is your Owner’s Manual. Read Carefully before operating your Remington POWERHAMMER Accessories Part No. Description 56485 Brush, . ...

Produzent Remington Kategorie Power Hammer

Dokumente, die wir vom Produzenten des Geräts Remington 476 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Remington
- Bedienungsanleitungen 476
- Produktkarten Remington
- Informationsbroschüren
- oder Energieetiketten Remington 476
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Remington 476.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Remington 476, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Remington 476. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Remington 476 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Remington 476, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Remington 476 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Remington 476 verständlich ist.

Eine gänzliche Bedienungsanleitung von Remington sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Remington 476 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Remington 476 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Remington 476, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Remington 476 - die uns die ersten Schritte während der Nutzung von Remington 476 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Remington 476 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Remington 476 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Remington 476?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Remington 476 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Remington 476 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)