Bedienungsanleitung QSC DCA Series

16 Seiten 0.84 mb
Download

Zur Seite of 16

Summary
  • QSC DCA Series - page 1

    1 Cinema Accessories for DCA Series amplifiers USER MANUAL ▼ ▼ ▼ ▼ ▼ XC-3 Two-way crossover with delay ▼ ▼ ▼ ▼ ▼ LF-3 Low-frequency filter with delay ▼ ▼ ▼ ▼ ▼ SF-3 Subwoofer filter *TD-000079-00* TD-000079-00 rev. B ...

  • QSC DCA Series - page 2

    2 ©Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC , ” “DCA , ” “DataPort , ” and the QSC logo are registered trademarks of QSC Audio Products, Inc. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsul ...

  • QSC DCA Series - page 3

    3 TABLE OF CONTENTS INTRODUCTION Introduction and d escription of e ach m odel.................................4 CONFIGURING THE ACCESSORIES General c onfiguration i nformation, all m odels...............................5 XC-3 Setting u p the XC-3....................................................................6 Factory -i nstalled SIPs......... ...

  • QSC DCA Series - page 4

    4 INTRODUCTION & DESCRIPTION OF EACH MODEL XC-3 This accessory is a two-way crossover, with the low frequency band fed to channel 1 of the amplifier and the high frequencies t o channel 2. An all-pass filter on the low frequency band delays the audio signal, permitting time alignment of a cone driver with a high-frequency horn. A selectable hig ...

  • QSC DCA Series - page 5

    5 CONFIGURING THE ACCESSORIES Configurable functions of the three accessory models Configure each accessory before you mount it to the ampli- fier. If an accessory is already mounted to an amplifier, always turn the amplifier off before changing switch set- tings, changing input or output connections, or detaching the accessory. Use the tables on t ...

  • QSC DCA Series - page 6

    6 XC-3 Setting u p the XC-3 Setting up the XC-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2, #9, and #10 must be set to the ON position (default settings for the XC-3). The flowchart below takes you through all the steps necessary before mounting the accessory to the amp. The ...

  • QSC DCA Series - page 7

    7 Use these tables to determine the correct resistor values for the crossover frequencies and delays you need. The shaded values are for the high-pass frequency (f HP ) of the XC-3. XC-3 Setting u p the XC-3 Effects of high frequency boost on frequency response (crossover frequency = 500 Hz). A boost of +10 dB is most common for compensating for sc ...

  • QSC DCA Series - page 8

    8 Setup flowchart for the LF-3 Setting up the LF-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2 and #4 through #9 must be set to OFF, and switch #3 set to ON (factory default for proper operation). The flowchart , right, takes you through the steps necessary before mounting th ...

  • QSC DCA Series - page 9

    9 LF-3 Setting Up the LF-3 LF-3 Factory-installed SIPs LF-3 Factory Switch Settings LF-3 Recommended Amplifier Settings f xo 350 Hz, both channels (18 k Ω SIP resistor installed in J6 and J8) Delay 1.4 milliseconds, both channels (22 k Ω SIP resistor installed in J1 and J2) Switch 1 and Switch 10 ON: Delay active (both channels) Switch 2 and Sw ...

  • QSC DCA Series - page 10

    10 Setting up the SF-3 SF-3 Setting u p the SF-3 Setting up the SF-3 requires setting the DIP switches, and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #1 through #6 and #10 must be set to OFF (factory default for proper operation). The flowchart, right, takes you through all the steps necessary before mounting the ...

  • QSC DCA Series - page 11

    11 SF-3 Factory-installed SIPs fHP= 30 Hz (27 k Ω SIP resistor in J2) fLP= 250 Hz (22 k Ω SIP resistor in J6) SF-3 Factory Switch Settings Switches 1 through 6 and Switch 10 OFF: Default setting for SF-3 Switches 7 & 8 ON: Low-pass filter off (“cinema” setting) Switch 9 OFF: LF flat When shipped from the factory, the DIP switch settings ...

  • QSC DCA Series - page 12

    12 An accessory may be mounted with the amplifier either in or out of the rack, even if the amp is installed with rear rack ears. MOUNTING- All Models Mounting the Accessories 1. Turn off the amplifier before installing the accessory. 2. Make sure the SIP resistor networks are installed properly and no SIP sockets are empty. 3. Line up the HD-15 co ...

  • QSC DCA Series - page 13

    13 Setting up the DCA Accessories in the Cinema Sound System If you are unable to obtain a satisfactory frequency response or SPL on a channel, carefully check the wiring and connections. Some likely causes are reversed speaker polarity on one or more drivers, loose or broken wiring or connections, or blown or damaged speaker drivers. 1. Set up the ...

  • QSC DCA Series - page 14

    14 Cleaning The faceplate and chassis can be cleaned with a soft cloth and nonabrasive, noncorrosive, mild cleaning solution. Products like Simple Green and Windex work well. Do not use powders or scrubbing pads of any type as they are usually abrasive and will permanently damage the finish of your cinema accessory. Dampen a soft, lint-free cloth w ...

  • QSC DCA Series - page 15

    15 WORLD WIDE WEB: http://www.qscaudio.com FACSIMILE (FAX) NUMBERS: Sales & Marketing FAX +1 (714) 754-6174 Technical Services FAX +1 (714) 754-6173 TELEPHONE NUMBERS: Main Number +1 (714) 754-6175 Sales Direct Line +1 (714) 957-7100 or (800) 854-4079 toll free (U.S.A. only) Technical Services (714) 957-7150 or (800) 772-2834 toll free (U.S.A. ...

  • QSC DCA Series - page 16

    16 © Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. QSC Audio Products, Inc., 1675 MacArthur Boulevard Costa Mesa, California 92626 USA PH: (714) 754-6175 FAX: (714) 754-6174 ...

Produzent QSC Kategorie Stereo Amplifier

Dokumente, die wir vom Produzenten des Geräts QSC DCA Series erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen QSC
- Bedienungsanleitungen DCA Series
- Produktkarten QSC
- Informationsbroschüren
- oder Energieetiketten QSC DCA Series
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung QSC DCA Series.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen QSC DCA Series, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen QSC DCA Series. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts QSC DCA Series ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts QSC DCA Series, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von QSC DCA Series hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von QSC DCA Series verständlich ist.

Eine gänzliche Bedienungsanleitung von QSC sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von QSC DCA Series bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von QSC DCA Series befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich QSC DCA Series, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts QSC DCA Series - die uns die ersten Schritte während der Nutzung von QSC DCA Series erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit QSC DCA Series hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von QSC DCA Series im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich QSC DCA Series?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit QSC DCA Series nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit QSC DCA Series hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)