Bedienungsanleitung Sigma AS-H60Y

20 Seiten 0.71 mb
Download

Zur Seite of 20

Summary
  • Sigma AS-H60Y - page 1

    AS-H40Y - 12kW AS-H50Y - 15kW AS-H60Y - 18kW AL TO Hea t Pump inst alla tion manu al F1-F7 ...

  • Sigma AS-H60Y - page 2

    1 CUSTOMER NAME........................................................................ POOL DEALER.............................................................................. DA TE INST ALLED.......................................................................... SERIAL NO........................................................................ ...

  • Sigma AS-H60Y - page 3

    HEA T PUMP- AS-H40Y 12kW 2 ...

  • Sigma AS-H60Y - page 4

    3 HEA T PUMP- AS-H50Y (15kW) & AS-H60 (18kW) ...

  • Sigma AS-H60Y - page 5

    INST ALLA TION AND SITING Prior to installing your heat pump:- All heat pumps are factory assembled and tested prior to delivery . Please check for any external damage especially to the evaporator fins, please diagram below . Do not be concerned about minor damage or indent ations to the fins (especially where the fan unit is mounted) as it will no ...

  • Sigma AS-H60Y - page 6

    5 PLUMBING Alto heat pumps are supplied with 1.5" BSP parallel threads, male. We strongly recommend a 1.5" female socket union is applied to inlet/outlets for future draining and servicing of the appliance. Alto heat pumps must be inst alled in the return line after the filter . If an existing heater or back-up heater has been installed t ...

  • Sigma AS-H60Y - page 7

    N L ON OFF CONT A CTOR 12 HEA TER Red Black OUTLET FLOW SWITCH OPERA TION WA TER FLOW FROM PUMP SOCKET UNION TEE INLET OFF ON Alternat ive w irin g route SOCKET UNION RETURN W A TE R FLOW TO POOL 1. Insert reducing bushes (provided) into 1.5” T ee using suitable adhesive. 2. Connect 1.5” T ee to socket union adjacent to Inlet on heat pump. T ee ...

  • Sigma AS-H60Y - page 8

    7 Ball Va l v e BACK WASH FILTER FIL TER Pool Position for option al Erosion Fe eder Non-Retur n V alve Back-Up Heater if required Condensat e W ater to waste PUMP Female/ Threade d Socket Union Drw .1 Recommended plumbing layout for a st andard heat pump installation. Drw .2 Recommended plumbing layout when incorporating Solar Heating. If an incre ...

  • Sigma AS-H60Y - page 9

    Ball Va l v e BACKW ASH FIL TER FIL TER Pool Non-R etu rn Valve Back-Up Heater if required Condensate W ater to waste PUMP Female/ Threaded Socket Union to be applied on all inlet/outlets Position for optional Erosion Feeder Ball Va l v e Ball Va l v e Condensate W ater to waste required or Erro sion Feede r if instal led Drw .4 Recommended plumbin ...

  • Sigma AS-H60Y - page 10

    9 ELECTRICAL CONNECTION & CIRCUIT DIAGRAM IMPORT ANT . It is recommended that all electrical supplies and connections are carried out by a qualified electrician , in accordance with I.E.E. standards, latest issue, or local codes of practice as applicable. Also recommended is a protected supply to incorporate fuses or motor type circuit breaker ...

  • Sigma AS-H60Y - page 11

    1. When electric supply is connected the ‘Run’ power light will be on and the display panel will display the current water temperature. ie.10 H = 10°C. 2. On/OFF button to turn heater on and off. 3. The ‘set’ button is used to set the F1-6 functions ie.water temperature, defrosting cycle and defrosting time etc. see pages 1 1-12 PLEASE REA ...

  • Sigma AS-H60Y - page 12

    11 When the ON/OFF buttons is pressed for the first time, the display panel will display the current water temperature and the desired pool temperature. eg. the display may read 10 40 ----- 10 is the current water temperature 10°C and 40 is the desired water temperature 40°C. ADJUSTING THE POOL W A TER TEMPERA TURE Using the up and down buttons, ...

  • Sigma AS-H60Y - page 13

    When the SET button is pressed for the fourth time, the display p anel will display:- F4 : Operation Mode. F4 C : Cooling Mode. F4 H : Heating Mode When the SET button is pressed for the fif th time, the display panel will display:- F5 : The defrosting temperature of the evaporator pipe . The recommended temperature setting for the UK should be set ...

  • Sigma AS-H60Y - page 14

    13 RED area RED area area RED area RED area area RED area RED area area After the water heater has been running for more than 24 hrs, it should be running at full capacity . The PSI reading should be in the region 150 -200. If you want to make the heat pump run more efficiently the water flow should be adjusted by checking the pressure meter displa ...

  • Sigma AS-H60Y - page 15

    E1 : the water temperature sensor is not working correctly . E2 : the tube sensor is not working correctly . Please contact your dealer . E3 : Pool filtration is running but water flow is not sensed. ‘Flow Switch’ may not be working properly or there is a lack of water flow . Backwash filter and check suction lines (Skimmer(s) & Main Drain( ...

  • Sigma AS-H60Y - page 16

    15 AUT O REST ART AND DEFROSTING FUNCTION AUTO REST ART FUNCTION The Alto water heat pump has an auto rest art function. When the power supply is switched off accidentally , it will automatically save the operation mode. When the power supply is restored, the unit will automatically restart af ter five minutes and operate in the same working mode. ...

  • Sigma AS-H60Y - page 17

    WINTERISING / ST ART -UP procedure - ALL MODELS W A TER CHEMISTR Y The following water quality must be maintained at all times to prevent premature corrosion. It is recommended that your water balance is checked and balanced by a pool professional. Y our warranty does not cover for damaged caused by poor water chemistry and neglect. pH: 7.2 -7.6 T ...

  • Sigma AS-H60Y - page 18

    17 AL T O W ARRANTY POLICY This voluntary policy is supplement al to and in no way affects any st atutory rights which the customer may have. 1 W arranties 1.1 Paramount Pools warrants the Alto Heat Pump for a period of one (1) year from the date installed for both part s and labour . 1.2 At the end of the first year the following warranties apply ...

  • Sigma AS-H60Y - page 19

    HEA T PUMP SER VICE An Alto heat pump should give you many years trouble free service. However , to obtain the maximum efficiency from your heater Alto recommend that your heater is checked and serviced every 12 months. Service & extended warranty packages are available from a UK Service Agent (see contact det ail below). HEA T PUMP BREAKDOWN I ...

  • Sigma AS-H60Y - page 20

    Model No. AS-H40Y AS-H50Y AS-H60Y 12kW 15kW 18kW Heating Capacity (Btu) 40000 50000 60000 Cooling Capacity (Btu) 35000 42000 55000 Rated Input (W) Heating 2540 3185 3790 Cooling 2465 3020 3900 PTC Power (W) -------- -------- -------- COP for Heating (w/w) 4.42 4.40 4.44 (at 20 °C ambient air temperature) Refrigerant R407C R407C R407C Power Supply ...

Produzent Sigma Kategorie Heat Pump

Dokumente, die wir vom Produzenten des Geräts Sigma AS-H60Y erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Sigma
- Bedienungsanleitungen AS-H60Y
- Produktkarten Sigma
- Informationsbroschüren
- oder Energieetiketten Sigma AS-H60Y
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Sigma AS-H60Y.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Sigma AS-H60Y, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Sigma AS-H60Y. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Sigma AS-H60Y ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Sigma AS-H60Y, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Sigma AS-H60Y hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Sigma AS-H60Y verständlich ist.

Eine gänzliche Bedienungsanleitung von Sigma sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Sigma AS-H60Y bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Sigma AS-H60Y befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Sigma AS-H60Y, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Sigma AS-H60Y - die uns die ersten Schritte während der Nutzung von Sigma AS-H60Y erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Sigma AS-H60Y hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Sigma AS-H60Y im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Sigma AS-H60Y?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sigma AS-H60Y nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sigma AS-H60Y hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)